When cancel_delayed_work() returns, the delayed work may still
be running. This means that the core could potentially free
the private structure (struct xadc) while the delayed work
is still using it. This is a potential use-after-free.

Fix by calling cancel_delayed_work_sync(), which waits for
any residual work to finish before returning.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.

This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

On some laptops, kxcjk1013 is powered off when system enters S3. We need
restore the range regiter during resume. Otherwise, the sensor doesn't
work properly after S3.
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: Chen, Hu <hu1.chen@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The SPI interface implementation was completely broken.

When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.

This fixes that the device wouldn't even probe in SPI mode.

The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.

Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.

The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.

Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd859 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The standard unit for temperature is millidegrees Celcius. Adapt the
driver to report in millidegrees instead of degrees.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd859 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

I clearly messed up applying this patch. Not sure
how but the entire Kconfig block is missing. This
patch puts it back as it was in the original patch.
Reported-by: Andreas Brauchli <a.brauchli@elementarea.net>
Fixes: ce514124 ("iio: chemical: sgp30: Support Sensirion SGP30/SGPC3 sensors")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

According to the datasheet, the last bit of CHIP_ID register controls
I2C bus, and the first one is unused. Handle this correctly.

Note that there are chips out there that have a value such that
the id check currently fails.
Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.

Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit 057ac1ac ("iio: Use kmalloc_array() in iio_scan_mask_set()").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch fixes the differential channels addresses for the ad7193.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Standard unit for temperature is millidegrees Celcius, whereas this driver
was reporting in degrees. Fix the scale factor in the driver.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch fixes an obvious typo, which will cause erroneously returning the Peak
Voltage instead of the Peak Current.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Cc: <Stable@vger.kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Pull io_uring IO interface from Jens Axboe:
 "Second attempt at adding the io_uring interface.

  Since the first one, we've added basic unit testing of the three
  system calls, that resides in liburing like the other unit tests that
  we have so far. It'll take a while to get full coverage of it, but
  we're working towards it. I've also added two basic test programs to
  tools/io_uring. One uses the raw interface and has support for all the
  various features that io_uring supports outside of standard IO, like
  fixed files, fixed IO buffers, and polled IO. The other uses the
  liburing API, and is a simplified version of cp(1).

  This adds support for a new IO interface, io_uring.

  io_uring allows an application to communicate with the kernel through
  two rings, the submission queue (SQ) and completion queue (CQ) ring.
  This allows for very efficient handling of IOs, see the v5 posting for
  some basic numbers:

    https://lore.kernel.org/linux-block/20190116175003.17880-1-axboe@kernel.dk/

  Outside of just efficiency, the interface is also flexible and
  extendable, and allows for future use cases like the upcoming NVMe
  key-value store API, networked IO, and so on. It also supports async
  buffered IO, something that we've always failed to support in the
  kernel.

  Outside of basic IO features, it supports async polled IO as well.
  This particular feature has already been tested at Facebook months ago
  for flash storage boxes, with 25-33% improvements. It makes polled IO
  actually useful for real world use cases, where even basic flash sees
  a nice win in terms of efficiency, latency, and performance. These
  boxes were IOPS bound before, now they are not.

  This series adds three new system calls. One for setting up an
  io_uring instance (io_uring_setup(2)), one for submitting/completing
  IO (io_uring_enter(2)), and one for aux functions like registrating
  file sets, buffers, etc (io_uring_register(2)). Through the help of
  Arnd, I've coordinated the syscall numbers so merge on that front
  should be painless.

  Jon did a writeup of the interface a while back, which (except for
  minor details that have been tweaked) is still accurate. Find that
  here:

    https://lwn.net/Articles/776703/

  Huge thanks to Al Viro for helping getting the reference cycle code
  correct, and to Jann Horn for his extensive reviews focused on both
  security and bugs in general.

  There's a userspace library that provides basic functionality for
  applications that don't need or want to care about how to fiddle with
  the rings directly. It has helpers to allow applications to easily set
  up an io_uring instance, and submit/complete IO through it without
  knowing about the intricacies of the rings. It also includes man pages
  (thanks to Jeff Moyer), and will continue to grow support helper
  functions and features as time progresses. Find it here:

    git://git.kernel.dk/liburing

  Fio has full support for the raw interface, both in the form of an IO
  engine (io_uring), but also with a small test application (t/io_uring)
  that can exercise and benchmark the interface"

* tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block:
  io_uring: add a few test tools
  io_uring: allow workqueue item to handle multiple buffered requests
  io_uring: add support for IORING_OP_POLL
  io_uring: add io_kiocb ref count
  io_uring: add submission polling
  io_uring: add file set registration
  net: split out functions related to registering inflight socket files
  io_uring: add support for pre-mapped user IO buffers
  block: implement bio helper to add iter bvec pages to bio
  io_uring: batch io_kiocb allocation
  io_uring: use fget/fput_many() for file references
  fs: add fget_many() and fput_many()
  io_uring: support for IO polling
  io_uring: add fsync support
  Add io_uring IO interface

Pull block layer updates from Jens Axboe:
 "Not a huge amount of changes in this round, the biggest one is that we
  finally have Mings multi-page bvec support merged. Apart from that,
  this pull request contains:

   - Small series that avoids quiescing the queue for sysfs changes that
     match what we currently have (Aleksei)

   - Series of bcache fixes (via Coly)

   - Series of lightnvm fixes (via Mathias)

   - NVMe pull request from Christoph. Nothing major, just SPDX/license
     cleanups, RR mp policy (Hannes), and little fixes (Bart,
     Chaitanya).

   - BFQ series (Paolo)

   - Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
     for the fast path (Jianchao)

   - fops->iopoll() added for async IO polling, this is a feature that
     the upcoming io_uring interface will use (Christoph, me)

   - Partition scan loop fixes (Dongli)

   - mtip32xx conversion from managed resource API (Christoph)

   - cdrom registration race fix (Guenter)

   - MD pull from Song, two minor fixes.

   - Various documentation fixes (Marcos)

   - Multi-page bvec feature. This brings a lot of nice improvements
     with it, like more efficient splitting, larger IOs can be supported
     without growing the bvec table size, and so on. (Ming)

   - Various little fixes to core and drivers"

* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
  block: fix updating bio's front segment size
  block: Replace function name in string with __func__
  nbd: propagate genlmsg_reply return code
  floppy: remove set but not used variable 'q'
  null_blk: fix checking for REQ_FUA
  block: fix NULL pointer dereference in register_disk
  fs: fix guard_bio_eod to check for real EOD errors
  blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
  block: optimize bvec iteration in bvec_iter_advance
  block: introduce mp_bvec_for_each_page() for iterating over page
  block: optimize blk_bio_segment_split for single-page bvec
  block: optimize __blk_segment_map_sg() for single-page bvec
  block: introduce bvec_nth_page()
  iomap: wire up the iopoll method
  block: add bio_set_polled() helper
  block: wire up block device iopoll method
  fs: add an iopoll method to struct file_operations
  loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
  loop: do not print warn message if partition scan is successful
  block: bounce: make sure that bvec table is updated
  ...

Pull libata updates from Jens Axboe:
 "Pretty quiet round: a few small fixes, comment typo, and most notably
  a low level driver for the PATA Buddha controller"

* tag 'for-5.1/libata-20190301' of git://git.kernel.dk/linux-block:
  ata: libahci: Only warn for AHCI_HFLAG_MULTI_MSI set when genuine custom irq handler implemented
  libata: fix a typo in comment
  ata: macio: Use of_node_name_eq for node name comparisons
  ata: pata_samsung_cf: simplify getting .driver_data
  ata: pata_platform: Add IRQF_SHARED to IRQ flags
  ata: pata_of_platform: Allow to use 16-bit wide data transfer
  ata: add Buddha PATA controller driver

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v5.1 cycle:

  Core changes:

   - The big change this time around is the irqchip handling in the
     qualcomm pin controllers, closely coupled with the gpiochip. This
     rework, in a classic fall-between-the-chairs fashion has been
     sidestepped for too long.

     The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
     have been rewritten to use hierarchical irqchip. This creates the
     base from which I intend to gradually pull support for hierarchical
     irqchips into the gpiolib irqchip helpers to cut down on duplicate
     code.

     We have too many hacks in the kernel because people have been
     working around the missing hierarchical irqchip for years, and once
     it was there, noone understood it for a while. We are now slowly
     adapting to using it.

     This is why this pull requests include changes to MFD, SPMI,
     IRQchip core and some ARM Device Trees pertaining to the Qualcomm
     chip family. Since Qualcomm have so many chips and such large
     deployments it is paramount that this platform gets this right, and
     now it (hopefully) does.

   - Core support for pull-up and pull-down configuration, also from the
     device tree. When a simple GPIO chip supports an "off or on" pull-up
     or pull-down resistor, we provide a way to set this up using
     machine descriptors or device tree.

     If more elaborate control of pull up/down (such as resistance shunt
     setting) is required, drivers should be phased over to use pin
     control. We do not yet provide a userspace ABI for this pull
     up-down setting but I suspect the makers are going to ask for it
     soon enough. PCA953x is the first user of this new API.

   - The GPIO mockup driver has been revamped after some discussion
     improving the IRQ simulator in the process.

     The idea is to make it possible to use the mockup for both testing
     and virtual prototyping, e.g. when you do not yet have a GPIO
     expander to play with but really want to get something to develop
     code around before hardware is available. It's neat. The blackbox
     testing usecase is currently making its way into kernelci.

   - ACPI GPIO core preserves non direction flags when updating flags.

   - A new device core helper for devm_platform_ioremap_resource() is
     funneled through the GPIO tree with Greg's ACK.

  New drivers:

   - TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)

   - Gateworks PLD GPIO driver (vaccumed up from OpenWrt)

   - AMD G-Series PCH (Platform Controller Hub) GPIO driver.

   - Fintek F81804 & F81966 subvariants.

   - PCA953x now supports NXP PCAL6416.

  Driver improvements:

   - IRQ support on the Nintendo Wii (Hollywood) GPIO.

   - get_direction() support for the MVEBU driver.

   - Set the right output level on SAMA5D2.

   - Drop the unused irq trigger setting on the Spreadtrum driver.

   - Wakeup support for PCA953x.

   - A slew of cleanups in the various Intel drivers"

* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
  gpio: gpio-omap: fix level interrupt idling
  gpio: amd-fch: Set proper output level for direction_output
  x86: apuv2: remove unused variable
  gpio: pca953x: Use PCA_LATCH_INT
  platform/x86: fix PCENGINES_APU2 Kconfig warning
  gpio: pca953x: Fix dereference of irq data in shutdown
  gpio: amd-fch: Fix type error found by sparse
  gpio: amd-fch: Drop const from resource
  gpio: mxc: add check to return defer probe if clock tree NOT ready
  gpio: ftgpio: Register per-instance irqchip
  gpio: ixp4xx: Add DT bindings
  x86: pcengines apuv2 gpio/leds/keys platform driver
  gpio: AMD G-Series PCH gpio driver
  drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
  gpio: tqmx86: Set proper output level for direction_output
  gpio: sprd: Change to use SoC compatible string
  gpio: sprd: Use SoC compatible string instead of wildcard string
  gpio: of: Handle both enable-gpio{,s}
  gpio: of: Restrict enable-gpio quirk to regulator-gpio
  gpio: davinci: use devm_platform_ioremap_resource()
  ...

Pull MFD updates from Lee Jones:
 "New Drivers:
   - Add STMPE ADC Input driver
   - Add STMicroelectronics STPMIC1 Parent driver
   - Add STMicroelectronics STPMIC1 OnKey Misc driver
   - Add STMicroelectronics STPMIC1 Watchdog driver
   - Add Cirrus Logic Lochnagar Parent driver
   - Add TQ-Systems TQMX86 Parent driver

  New Device Support:
   - Add support for ADC to STMPE

  New (or moved) Functionality:
   - Move Lightbar functionality to its own driver; cros_ec_lightbar
   - Move VBC functionality to its own driver; cros_ec_vbc
   - Move VBC functionality to its own driver; cros_ec_vbc
   - Move DebugFS functionality to its own driver; cros_ec_debugfs
   - Move SYSFS functionality to its own driver; cros_ec_sysfs
   - Add support for input voltage options; tps65218

  Fixes:
   - Use devm_* managed resources; cros_ec
   - Device Tree documentation; stmpe, aspeed-lpc, lochnagar
   - Trivial Clean-ups; stmpe
   - Rip out broken modular code; aat2870-core, adp5520, as3711,
         db8500-prcmu, htc-i2cpld, max8925-core, rc5t583, sta2x11-mfd,
	 syscon, tps65090, tps65910, tps68470 tps80031, wm831x-spi,
	 wm831x-i2c, wm831x-core, wm8350-i2c, wm8350-core, wm8400-core
   - Kconfig fixups; INTEL_SOC_PMIC
   - Improve error path; sm501, sec-core
   - Use struct_size() helper; sm501
   - Constify; at91-usart
   - Use pointers instead of copying data; at91-usart
   - Deliver proper return value; cros_ec_dev
   - Trivial formatting/whitespace; sec-core"

* tag 'mfd-next-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
  mfd: mxs-lradc: Mark expected switch fall-through
  mfd: sec-core: Cleanup formatting to a consistent style
  mfd: tqmx86: IO controller with I2C, Wachdog and GPIO
  mfd: intel-lpss: Move linux/pm.h to the local header
  mfd: cros_ec_dev: Return number of bytes read with CROS_EC_DEV_IOCRDMEM
  mfd: tps68470: Drop unused MODULE_DEVICE_TABLE
  mfd: at91-usart: No need to copy mfd_cell in probe
  mfd: at91-usart: Constify at91_usart_spi_subdev and at91_usart_serial_subdev
  mfd: lochnagar: Add support for the Cirrus Logic Lochnagar
  mfd: lochnagar: Add initial binding documentation
  dt-bindings: mfd: aspeed-lpc: Make parameter optional
  mfd: sec-core: Return gracefully instead of BUG() if device cannot match
  mfd: sm501: Use struct_size() in devm_kzalloc()
  mfd: sm501: Fix potential NULL pointer dereference
  mfd: Kconfig: Fix I2C_DESIGNWARE_PLATFORM dependencies
  mfd: tps65218.c: Add input voltage options
  mfd: wm8400-core: Make it explicitly non-modular
  mfd: wm8350-core: Drop unused module infrastructure from non-modular code
  mfd: wm8350-i2c: Make it explicitly non-modular
  mfd: wm831x-core: Drop unused module infrastructure from non-modular code
  ...

Pull backlight fixlet from Lee Jones:
 "Allow GPIO call to sleep in pwm_bl driver"

* tag 'backlight-next-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: pwm_bl: Use gpiod_get_value_cansleep() to get initial state

Pull RTC updates from Alexandre Belloni:
 "There is an unusual amount of new drivers this cycle, and this
  explains the number of insertions.

  Other than that, the changes are the usual fixes and feature addition.

  Subsystem updates:
   - new quartz-load-femtofarads DT property for quartz load capacitance
   - remove rtc_class_ops.read_callback

  New drivers:
   - Abracon AB-RTCMC-32.768kHz-EOZ9
   - Amlogic Meson RTC
   - Cadence RTC IP
   - Microcrystal RV3028
   - Whwave sd3078

  Driver updates:
   - cmos: ignore bogus century byte
   - ds1307: rework rx8130 support
   - isl1208: add isl1209 support, nvmem support
   - rs5C372: report invalid time when the oscillator stopped
   - rx8581: add rx8571 support"

* tag 'rtc-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (66 commits)
  rtc: pic32: convert to SPDX identifier
  rtc: pic32: let the core handle range
  rtc: pic32: convert to devm_rtc_allocate_device
  rtc: update my email address
  rtc: rv8803: convert to SPDX identifier
  rtc: rv8803: let the core handle range
  rtc: tx4939: convert to SPDX identifier
  rtc: tx4939: use .set_time
  rtc: tx4939: switch to rtc_time64_to_tm/rtc_tm_to_time64
  rtc: tx4939: set range
  rtc: tx4939: remove useless test
  rtc: zynqmp: let the core handle range
  rtc: zynqmp: fix possible race condition
  rtc: imx-sc: use rtc_time64_to_tm
  rtc: rx8581: Add support for Epson rx8571 RTC
  dt-bindings: rtc: add rx8571 compatible
  rtc: pcf85063: remove dead code
  rtc: remove rtc_class_ops.read_callback
  rtc: add AB-RTCMC-32.768kHz-EOZ9 RTC support
  dt-bindings: rtc: add ABEOZ9
  ...

Pull thermal soc updates from Eduardo Valentin:
 "Specifics:

   - mediatek thermal now supports MT8183

   - broadcom thermal now supports Stingray

   - qoirq now supports multiple sensors

   - fixes on different drivers: rcar, tsens, tegra

  Some new drivers are still pending further review and I chose to leave
  them for the next merge window while still sending this material"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: rcar_gen3_thermal: Register hwmon sysfs interface
  thermal/qcom/tsens-common : fix possible object reference leak
  thermal: tegra: add get_trend ops
  thermal: tegra: fix memory allocation
  thermal: tegra: remove unnecessary warnings
  thermal: mediatek: add support for MT8183
  dt-bindings: thermal: add binding document for mt8183 thermal controller
  thermal: mediatek: add flag for bank selection
  thermal: mediatek: add thermal controller offset
  thermal: mediatek: add calibration item
  thermal: mediatek: add common index of vts settings.
  thermal: mediatek: fix register index error
  thermal: qoriq: add multiple sensors support
  thermal: broadcom: Add Stingray thermal driver
  dt-bindings: thermal: Add binding document for SR thermal

Pull ibft updates from Konrad Rzeszutek Wilk:
 "Two tiny fixes - a missing break, and upgrading the subsystem to use
  modern macros"

* 'stable/for-linus-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
  iscsi_ibft: use virt_to_phys instead of isa_virt_to_bus
  iscsi_ibft: Fix missing break in switch statement

Pull swiotlb updates from Konrad Rzeszutek Wilk:
 "Expands the SWIOTLB to have debugfs support (along with bug-fixes),
  and a tiny fix"

* 'stable/for-linus-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: drop pointless static qualifier in swiotlb_create_debugfs()
  swiotlb: checking whether swiotlb buffer is full with io_tlb_used
  swiotlb: add debugfs to track swiotlb buffer usage
  swiotlb: fix comment on swiotlb_bounce()

Pull i2c updates from Wolfram Sang:

 - the I2C core gained helpers to assist drivers in handling their
   suspended state, and drivers were converted to use it

 - two new fault-injectors for stress-testing

 - bigger refactoring and feature improvements for the ocores,
   sh_mobile, and tegra drivers

 - platform_data removal for the at24 EEPROM driver

 - ... and various improvements and bugfixes all over the subsystem

* 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits)
  i2c: Allow recovery of the initial IRQ by an I2C client device.
  i2c: ocores: turn incomplete kdoc into a comment
  i2c: designware: Do not allow i2c_dw_xfer() calls while suspended
  i2c: tegra: Only display error messages if DMA setup fails
  i2c: gpio: fault-injector: add 'inject_panic' injector
  i2c: gpio: fault-injector: add 'lose_arbitration' injector
  i2c: tegra: remove multi-master support
  i2c: tegra: remove master fifo support on tegra186
  i2c: tegra: change phrasing, "fallbacking" to "falling back"
  i2c: expand minor range when registering chrdev region
  i2c: aspeed: Add multi-master use case support
  i2c: core-smbus: don't trace smbus_reply data on errors
  i2c: ocores: Add support for bus clock via platform data
  i2c: ocores: Add support for IO mapper registers.
  i2c: ocores: checkpatch fixes
  i2c: ocores: add SPDX tag
  i2c: ocores: add polling interface
  i2c: ocores: do not handle IRQ if IF is not set
  i2c: ocores: stop transfer on timeout
  i2c: tegra: add i2c interface timing support
  ...

Pull power supply and reset updates from Sebastian Reichel:
 "Nothing too fancy in the power-supply subsystem this time. There are
  less patches than usual, since I did not have enough time to review
  them in time. The good news is, that all patches have been in
  linux-next for more than two weeks and there are no complicated
  cross-subsystem patchsets this time!

  Summary:

   - at91-reset: add sam9x60 support

   - sc27xx: improve capacity logic

   - goldfish_battery: enhance driver by adding many new properties

   - isp1704: drop platform data and migrate to gpiod

   - misc small fixes and improvements"

* tag 'for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (25 commits)
  power: reset: at91-reset: add support for sam9x60 SoC
  dt-bindings: arm: atmel: add new sam9x60 reset controller binding
  dt-bindings: arm: atmel: add missing samx7 to reset controller
  max17042_battery: fix potential use-after-free on device remove
  power: supply: core: Add a field to support battery max voltage
  dt-bindings: power: supply: Add voltage-max-design-microvolt property
  bq27x00: use cached flags
  power: supply: ds2782: fix possible use-after-free on remove
  power: supply: bq25890: show max charge current/voltage as configured
  power: supply: sc27xx: Fix capacity saving function
  power: supply: sc27xx: Fix the incorrect formula when converting capacity to coulomb counter
  power: supply: sc27xx: Add one property to read charge voltage
  dt-bindings: power: sc27xx: Add one IIO channel to read charge voltage
  drivers: power: supply: goldfish_battery: Add support for reading more properties
  power: supply: charger-manager: Fix trivial language typos
  cpcap-charger: generate events for userspace
  power: supply: remove some duplicated includes
  power: twl4030: fix a missing check of return value
  drivers: power: supply: goldfish_battery: Use tabs for alignment
  drivers: power: supply: goldfish_battery: Fix alignment
  ...

Pull HIS update from Sebastian Reichel:
 "Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE"

* tag 'hsi-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  HSI: omap_ssi_port: fix debugfs_simple_attr.cocci warnings

Pull IPMI updates from Corey Minyard:
 "A couple of bug fixes and a bunch of code cleanup:

   - Fix a use after free error in a certain error situation.

   - Fix some flag handling issues in the SSIF (I2C) IPMI driver.

   - A bunch of cleanups, spacing issues, converting pr_xxx to dev_xxx,
     use standard UUID handling, and some other minor stuff.

   - The IPMI code was creating a platform device if none was supplied.
     Instead of doing that, have every source that creates an IPMI
     device supply a device struct. This fixes several issues,including
     a crash in one situation, and cleans things up a bit"

* tag 'for-linus-5.1' of git://github.com/cminyard/linux-ipmi:
  ipmi_si: Potential array underflow in hotmod_handler()
  ipmi_si: Remove hacks for adding a dummy platform devices
  ipmi_si: Consolidate scanning the platform bus
  ipmi_si: Remove hotmod devices on removal and exit
  ipmi_si: Remove hardcode IPMI devices by scanning the platform bus
  ipmi_si: Switch hotmod to use a platform device
  ipmi: Consolidate the adding of platform devices
  ipmi_si: Rename addr_type to addr_space to match what it does
  ipmi_si: Convert some types into unsigned
  ipmi_si: Fix crash when using hard-coded device
  ipmi: Use dedicated API for copying a UUID
  ipmi: Use defined constant for UUID representation
  ipmi:ssif: Change some pr_xxx to dev_xxx calls
  ipmi: kcs_bmc: handle devm_kasprintf() failure case
  ipmi: Fix return value when a message is truncated
  ipmi: clean an indentation issue, remove extraneous space
  ipmi: Make the smi watcher be disabled immediately when not needed
  ipmi: Fix how the lower layers are told to watch for messages
  ipmi: Fix SSIF flag requests
  ipmi_si: fix use-after-free of resource->name

Pull RAS updates from Borislav Petkov:
 "This time around we have in store:

   - Disable MC4_MISC thresholding banks on all AMD family 0x15 models
     (Shirish S)

   - AMD MCE error descriptions update and error decode improvements
     (Yazen Ghannam)

   - The usual smaller conversions and fixes"

* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Improve error message when kernel cannot recover, p2
  EDAC/mce_amd: Decode MCA_STATUS in bit definition order
  EDAC/mce_amd: Decode MCA_STATUS[Scrub] bit
  EDAC, mce_amd: Print ExtErrorCode and description on a single line
  EDAC, mce_amd: Match error descriptions to latest documentation
  x86/MCE/AMD, EDAC/mce_amd: Add new error descriptions for some SMCA bank types
  x86/MCE/AMD, EDAC/mce_amd: Add new McaTypes for CS, PSP, and SMU units
  x86/MCE/AMD, EDAC/mce_amd: Add new MP5, NBIO, and PCIE SMCA bank types
  RAS: Add a MAINTAINERS entry
  RAS: Use consistent types for UUIDs
  x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk
  x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models
  x86/MCE: Switch to use the new generic UUID API

Pull EDAC updates from Borislav Petkov:

 - A new EDAC AST 2500 SoC driver (Stefan M Schaeckeler)

 - New i10nm EDAC driver for Intel 10nm CPUs (Qiuxu Zhuo and Tony Luck)

 - Altera SDRAM functionality carveout for separate enablement of RAS
   and SDRAM capabilities on some Altera chips. (Thor Thayer)

 - The usual round of cleanups and fixes

And last but not least: recruit James Morse as a reviewer for the ARM
side.

* tag 'edac_for_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC/altera: Add separate SDRAM EDAC config
  EDAC, altera: Add missing of_node_put()
  EDAC, skx_common: Add code to recognise new compound error code
  EDAC, i10nm: Fix randconfig builds
  EDAC, i10nm: Add a driver for Intel 10nm server processors
  EDAC, skx_edac: Delete duplicated code
  EDAC, skx_common: Separate common code out from skx_edac
  EDAC: Do not check return value of debugfs_create() functions
  EDAC: Add James Morse as a reviewer
  dt-bindings, EDAC: Add Aspeed AST2500
  EDAC, aspeed: Add an Aspeed AST2500 EDAC driver

Pull HID updates from Jiri Kosina:

 - support for Pro Pen slim, from Jason Gerecke

 - power management improvements to Intel-ISH driver, from Song Hongyan

 - UCLogic driver revamp in order to be able to support wider range of
   Huion tablets, from Nikolai Kondrashov

 - Asus Transbook support, from NOGUCHI Hiroshi

 - other assorted small bugfixes / cleanups and device ID additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (46 commits)
  HID: Remove Waltop tablets from hid_have_special_driver
  HID: Remove KYE tablets from hid_have_special_driver
  HID: Remove hid-uclogic entries from hid_have_special_driver
  HID: uclogic: Do not initialize non-USB devices
  HID: uclogic: Add support for Ugee G5
  HID: uclogic: Support Gray-coded rotary encoders
  HID: uclogic: Support faking Wacom pad device ID
  HID: uclogic: Add support for XP-Pen Deco 01
  HID: uclogic: Add support for XP-Pen Star G640
  HID: uclogic: Add support for XP-Pen Star G540
  HID: uclogic: Add support for Ugee EX07S frame controls
  HID: uclogic: Add support for Ugee M540
  HID: uclogic: Add support for Ugee 2150
  HID: uclogic: Support v2 protocol
  HID: uclogic: Support fragmented high-res reports
  HID: uclogic: Support in-range reporting emulation
  HID: uclogic: Designate current protocol v1
  HID: uclogic: Re-initialize tablets on resume
  HID: uclogic: Extract tablet parameter discovery into a module
  HID: uclogic: Extract report descriptors to a module
  ...

Pull livepatching updates from Jiri Kosina:

 - support for something we call 'atomic replace', and allows for much
   better handling of cumulative patches (which is something very useful
   for distros), from Jason Baron with help of Petr Mladek and Joe
   Lawrence

 - improvement of handling of tasks blocking finalization, from Miroslav
   Benes

 - update of MAINTAINERS file to reflect move towards group
   maintainership

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching: (22 commits)
  livepatch/selftests: use "$@" to preserve argument list
  livepatch: Module coming and going callbacks can proceed with all listed patches
  livepatch: Proper error handling in the shadow variables selftest
  livepatch: return -ENOMEM on ptr_id() allocation failure
  livepatch: Introduce klp_for_each_patch macro
  livepatch: core: Return EOPNOTSUPP instead of ENOSYS
  selftests/livepatch: add DYNAMIC_DEBUG config dependency
  livepatch: samples: non static warnings fix
  livepatch: update MAINTAINERS
  livepatch: Remove signal sysfs attribute
  livepatch: Send a fake signal periodically
  selftests/livepatch: introduce tests
  livepatch: Remove ordering (stacking) of the livepatches
  livepatch: Atomic replace and cumulative patches documentation
  livepatch: Remove Nop structures when unused
  livepatch: Add atomic replace
  livepatch: Use lists to manage patches, objects and functions
  livepatch: Simplify API by removing registration step
  livepatch: Don't block the removal of patches loaded after a forced transition
  livepatch: Consolidate klp_free functions
  ...

Pull drm updates from Dave Airlie:
 "This is the main drm pull request for the 5.1 merge window.

  The big changes I'd highlight are:
   - nouveau has HMM support now, there is finally an in-tree user so we
     can quieten down the rip it out people.
   - i915 now enables fastboot by default on Skylake+
   - Displayport Multistream support has been refactored and should
     hopefully be more reliable.

  Core:
   - header cleanups aiming towards removing drmP.h
   - dma-buf fence seqnos to 64-bits
   - common helper for DP mst hotplug for radeon,i915,amdgpu + new
     refcounting scheme
   - MST i2c improvements
   - drm_syncobj_cb removal
   - ARM FB compression fourcc
   - P010 + P016 fourcc
   - allwinner tiled format modifier
   - i2c over aux I2C_M_STOP support
   - DRM_AUTH handling fixes

  TTM:
   - ref/unref renaming

  New driver:
   - ARM komeda display driver

  scheduler:
   - refactor mirror list handling
   - rework hw fence processing
   - 0 run queue entity fix

  bridge:
   - TI DS90C185 LVDS bridge
   - thc631lvdm83d bridge improvements
   - cadence + allwinner DSI ported to generic phy

  panels:
   - Sitronix ST7701 panel
   - Kingdisplay KD097D04
   - LeMaker BL035-RGB-002
   - PDA 91-00156-A0
   - Innolux EE101IA-01D

  i915:
   - Enable fastboot by default on SKL+/VLV/CHV
   - Export RPCS configuration for ICL media driver
   - Coffelake PCI ID
   - CNL clocks setup fixes
   - ACPI/PMIC support for MIPI/DSI
   - Per-engine WA init for all engines
   - Shrinker locking fixes
   - Kerneldoc updates
   - Lots of ring improvements and reset fixes
   - Coffeelake GVT Support
   - VFIO GVT EDID Region support
   - runtime PM wakeref tracking
   - ILK->IVB primary plane enable delays
   - userptr mutex locking fixes
   - DSI fixes
   - LVDS/TV cleanups
   - HW readout fixes
   - LUT robustness fixes
   - ICL display and watermark fixes
   - gem mmap race fix

  amdgpu:
   - add scheduled dependencies interface
   - DCC on scanout surfaces
   - vega10/20 BACO support
   - Multiple IH rings on soc15
   - XGMI locking fixes
   - DC i2c/aux cleanups
   - runtime SMU debug interface
   - Kexec improvmeents
   - SR-IOV fixes
   - DC freesync + ABM fixes
   - GDS fixes
   - GPUVM fixes
   - vega20 PCIE DPM switching fixes
   - Context priority handling fixes

  radeon:
   - fix missing break in evergreen parser

  nouveau:
   - SVM support via HMM

  msm:
   - QCOM Compressed modifier support

  exynos:
   - s5pv210 rotator support

  imx:
   - zpos property support
   - pending update fixes

  v3d:
   - cache flush improvments

  vc4:
   - reflection support
   - HDMI overscan support

  tegra:
   - CEC refactoring
   - HDMI audio fixes
   - Tegra186 prep work
   - SOR crossbar device tree fixes

  sun4i:
   - implicit fencing support
   - YUV and scalar support improvements
   - A23 support
   - tiling fixes

  atmel-hlcdc:
   - clipping and rotation property fixes

  qxl:
   - BO and PRIME improvements
   - generic fbdev emulation

  dw-hdmi:
   - HDMI 2.0 2160p
   - YUV420 ouput

  rockchip:
   - implicit fencing support
   - reflection proerties

  virtio-gpu:
   - use generic fbdev emulation

  tilcdc:
   - cpufreq vs crtc init fix

  rcar-du:
   - R8A774C0 support
   - D3/E3 RGB output routing fixes and DPAD0 support
   - RA87744 LVDS support

  bochs:
   - atomic and generic fbdev emulation
   - ID mismatch error on bochs load

  meson:
   - remove firmware fbs"

* tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits)
  drm/amd/display: Use vrr friendly pageflip throttling in DC.
  drm/imx: only send commit done event when all state has been applied
  drm/imx: allow building under COMPILE_TEST
  drm/imx: imx-tve: depend on COMMON_CLK
  drm/imx: ipuv3-plane: add zpos property
  drm/imx: ipuv3-plane: add function to query atomic update status
  gpu: ipu-v3: prg: add function to get channel configure status
  gpu: ipu-v3: pre: add double buffer status readback
  drm/amdgpu: Bump amdgpu version for context priority override.
  drm/amdgpu/powerplay: fix typo in BACO header guards
  drm/amdgpu/powerplay: fix return codes in BACO code
  drm/amdgpu: add missing license on baco files
  drm/bochs: Fix the ID mismatch error
  drm/nouveau/dmem: use dma addresses during migration copies
  drm/nouveau/dmem: use physical vram addresses during migration copies
  drm/nouveau/dmem: extend copy function to allow direct use of physical addresses
  drm/nouveau/svm: new ioctl to migrate process memory to GPU memory
  drm/nouveau/dmem: device memory helpers for SVM
  drm/nouveau/svm: initial support for shared virtual memory
  drm/nouveau: prepare for enabling svm with existing userspace interfaces
  ...

Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.

After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.

It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:

CAUTION
  After servicing the interrupt, the status bit in the interrupt status
  register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
  reset and the interrupt line released (by setting the corresponding
  bit of the interrupt status register to 1) before enabling an
  interrupt for the GPIO channel in the interrupt-enable register
  (GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
  the occurrence of unexpected interrupts when enabling an interrupt
  for the GPIO channel.

However, this does not appear to be a practical problem.

Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:

 if the status is cleared after disabling the IRQ then sWAKEUP will not
 be cleared and gates the module transition

When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.

Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Current amd_fch_gpio_direction_output implementation ignores the value
argument, fix it so direction_output will set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver was newly introduced but the version that got merged
produces a harmless compiler warning:

drivers/platform/x86/pcengines-apuv2.c: In function 'apu_board_init':
drivers/platform/x86/pcengines-apuv2.c:211:6: error: unused variable 'rc' [-Werror=unused-variable]

Remove the evidently useless variable.

Fixes: f8eb0235 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-By: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The commit 0cdf21b3

  ("gpio: pca953x: set the PCA_PCAL flag also when matching by DT")

introduces a helper macro which tells that chip supports latched interrupts,
but the macro was never used for ACPI or legacy enumeration.

So, make use of it for legacy and ACPI enumeration.

Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix Kconfig warning for PCENGINES_APU2 symbol:

WARNING: unmet direct dependencies detected for KEYBOARD_GPIO_POLLED
  Depends on [n]: !UML && INPUT [=y] && INPUT_KEYBOARD [=n] && GPIOLIB [=y]
  Selected by [y]:
  - PCENGINES_APU2 [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y]

Add INPUT_KEYBOARD dependency for KEYBOARD_GPIO_POLLED.
Add LEDS_CLASS dependency for LEDS_GPIO.

Fixes: f8eb0235 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge more updates from Andrew Morton:

 - some of the rest of MM

 - various misc things

 - dynamic-debug updates

 - checkpatch

 - some epoll speedups

 - autofs

 - rapidio

 - lib/, lib/lzo/ updates

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
  samples/mic/mpssd/mpssd.h: remove duplicate header
  kernel/fork.c: remove duplicated include
  include/linux/relay.h: fix percpu annotation in struct rchan
  arch/nios2/mm/fault.c: remove duplicate include
  unicore32: stop printing the virtual memory layout
  MAINTAINERS: fix GTA02 entry and mark as orphan
  mm: create the new vm_fault_t type
  arm, s390, unicore32: remove oneliner wrappers for memblock_alloc()
  arch: simplify several early memory allocations
  openrisc: simplify pte_alloc_one_kernel()
  sh: prefer memblock APIs returning virtual address
  microblaze: prefer memblock API returning virtual address
  powerpc: prefer memblock APIs returning virtual address
  lib/lzo: separate lzo-rle from lzo
  lib/lzo: implement run-length encoding
  lib/lzo: fast 8-byte copy on arm64
  lib/lzo: 64-bit CTZ on arm64
  lib/lzo: tidy-up ifdefs
  ipc/sem.c: replace kvmalloc/memset with kvzalloc and use struct_size
  ipc: annotate implicit fall through
  ...

Remove duplicate headers which are included more than once

Link: http://lkml.kernel.org/r/20190114170033.GA3674@hp-pavilion-15-notebook-pc-brajeswarSigned-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove duplicated include.

Link: http://lkml.kernel.org/r/20181209062952.17736-1-yuehaibing@huawei.comSigned-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The percpu member of this structure is declared as:
	struct ... ** __percpu member;
So its type is:
	__percpu pointer to pointer to struct ...

But looking at how it's used, its type should be:
	pointer to __percpu pointer to struct ...
and it should thus be declared as:
	struct ... * __percpu *member;

So fix the placement of '__percpu' in the definition of this
structures.

This silents a few Sparse's warnings like:
	warning: incorrect type in initializer (different address spaces)
	  expected void const [noderef] <asn:3> *__vpp_verify
	  got struct sched_domain **

Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com
Fixes: 017c59c0 ("relay: Use per CPU constructs for the relay channel buffer pointers")
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>