Patch from Tony Lindgren

This patch by Dirk Behme, Todd Poynor et al adds power management
support for OMAP. Suspend works on at least 1510 and 16xx.

Signed-off-by: Tony Lindgren

Patch from Ben Dooks

This patch does the following:

- move the clock initialisation to just after the cpu init
- add the two clocks for the s3c2440
- add dclk0/1 and clkout0/1 definitions
- add list of clocks to the board specific struct
- fix initialisation of the clock control
- update handling of parent clocks for >1 parent

this fixes the following problems:

- serial console with no clock sources
- clocks specific to various boards
- hang if LCD controller enabled at start time

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Allow power managemnet support for the Simtec EB2410ITX (BAST)

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Allow the uncompressing messages to be sent to the UART
specified in the kernel configuration, instead of just
UART 0. This includes the Kconfig update to make this
option available all the time, and to rename it's
description text.

This patch also fixes s3c2440 support for the
uncompressor

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Header file for BAST Power Management unit register
definitions

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Clean warnings about unsigned long / unsigned int printk args
and update comment on debugging

Depends on patch 2134/3

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Updated default configurations for s3c2410 and bast

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Update the following in Documentation/arm/Samsing-S3C24XX/

- mtd merge update
- list of contributors
- change history

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Attached is the fix for the S3C2410_UDC_MAXP_REG
definition.

Signed-off-by: Ben Dooks 
Signed-off-by: Arnaud Patard 

Patch from Ben Dooks

Fix the mis-definition of the following registers / bits
in the s3c2410 LCD controller register header:

- S3C2410_LCDCON1_MMODE
- S3C2410_LCDCON1_ENVID
- S3C2410_LCDCON3_HBPD
- S3C2410_LCDCON3_WDLY

and adds the following missing register definitoons

- S3C2410_LCDBANK
- S3C2410_LCDBASEU
- S3C2410_OFFSIZE
- S3C2410_PAGEWIDTH

thanks to Arnaud Patard for finding these problems

Signed-off-by: Ben Dooks 
Signed-off-by: Arnaud Patard 

Patch from Ben Dooks

fix guard define so it does not clash with another header
file.

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

This patch does the following

 - removes the setup code to change device/host
   behaviour, which does not belong here

 - tidies up the debug output

 - fixes the call to free_irq() to pass the
   right info

 - ensures the usb code is notified when the
   over-current condition is removed

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Attached is the include file for the i2c platform data
for the s3c2410/s3c2440 I2C controller

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

this patch makes the following changes:

 - renames struct s3c2410_board to s3c24xx_board
 - moves board registration into cpu.c

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

fixes the following:

 - no debug output in the head code for either s3c2410 or s3c2440
 - fifo size calculation in the low-level debugging code
 - serial constants for s3c2440 serial fifo sizes
 - added s3c2440 support for uncompress.h

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Documentation for the suspend and resume code in
Documentation/arm/Samsung-S3C24XX/Suspend.txt

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Allow all wake-up capable IRQs to be configured
as such

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Support for restarting the system timer after a suspend-resume
cycle.

Also fixes the following

 - missed partial setup for BAST and VR1000
 - added IPAQ RX3715 timer setup

Signed-off-by: Ben Dooks 

Patch from Ben Dooks

Core support for S3C2410 suspend to SDRAM

Signed-off-by: Ben Dooks 

Patch from Tony Lindgren

This patch syncs the mainline kernel with the linux-omap tree.
The highlights of the patch are:
- Collapse OMAP 1610, 6912 and 1710 into one processor group 16xx
- USB updates by David Brownell
- Pin multiplexing updates by David Brownell
- Board specific low level serial port init

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

Patch by Samuel Ortiz to update OMAP McBSP support

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

This patch by Imre Deak adds support for graphics acceleration
features on the OMAP DMA controller.

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

This patch by Tuukka Tikkanen changes OMAP to use ARM generic
clock framework instead of older OMAP specific clock framework.
Patch replaces old clocks.c with new clock.[ch].

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

This patch replaces old OMAP headers for 1610 and 5912. These
headers are replaced with a common omap16xx.h header file.

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

This patch syncs the mainline kernel with the linux-omap tree.
The highlights of the patch are:
- Collapse OMAP 1610, 6912 and 1710 into one processor group 16xx
- USB updates by David Brownell
- Pin multiplexing updates by David Brownell
- Board specific low level serial port init

Signed-off-by: Tony Lindgren

Patch from Tony Lindgren

This patch improves the OMAP cpu detection during the boot,
and adds board-specific init for the serial ports.

Signed-off-by: Tony Lindgren

fork.c highlighted that we were missing some parens.  Add them.

This marks sets change_bits to all ones when bringing up a hub, since
not all hubs seem to send change events for devices that were plugged in
when the hub was reset. 

David Miller confirms this fixes his boot-time lost keyboard/mouse
problem

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into kroah.com:/home/greg/linux/BK/usb-2.6

This updates debug messages, declaring that labels can be constant strings
and changing some old-school dbg() calls to driver model dev_dbg().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

The recent patch to scrub out ep0 state earlier (to get rid of some of
the enumeration problems that started with about 2.6.6) requires EHCI
to handle endpoint_disable() calls in a slightly different context.

This makes those calls work when an endpoint's QH may still be on the
async schedule, rather than already unlinked.  (The QH stays on the async
schedule for a few milliseconds after it's empty, since it's routine to
issue another request almost immediately.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

This has minor PCI tweaks for the EHCI driver:

  - If the (nonfunctional) AMD 8111 controller shows up, ignore it.
    (Patch from Matt Dharm, with minor coding style tweaks).

  - Delete some code that interprets an EHCI capability code; it
    should be a PCI capability instead.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

New and Improved! "Woozy Numbat!"

Pick up the phone in the next two minutes and phone in your
order, and we'll throw in a second copy of Woozy Numbat,
ABSOLUTELY FREE! You too could start a Numbat farm!

lib/kobject_uevent.c:39: warning: `action_to_string' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

From: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>

Remove cpu_run_sbin_hotplug() - use kobject_hotplug() instead.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Make kobject_hotplug() work even if the kobject's kset doesn't implement any
hotplug_ops.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>