- 10 Mar, 2011 8 commits
-
-
Matt Carlson authored
In the near future, the VAux switching decision process is going to get more complicated. This patch refines and consolidates the existing algorithm in anticipation of the new scheme. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Commit 895950c2, entitled "tg3: Use DEFINE_PCI_DEVICE_TABLE" moved two pci device tables into the global address space, but didn't declare them static and didn't prefix them with "tg3_". This patch fixes those problems. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch adds code to verify the checksum stored in the "RV" info keyword of the RODATA VPD section. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
The tg3 NVRAM selftest actually fails when validating the checksum of the legacy NVRAM format. However, the test still reported success because the last update of the return code was a success from the NVRAM reads. This patch fixes the code so that the error return code defaults to a failure status. Then the patch fixes the reason why the checsum validation failed. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Commit 2866d956, entitled "tg3: Expand 5719 workaround" extended a 5719 A0 workaround to all revisions of the chip. There was a change that should have been a part of that patch that was missed. This patch adds the missing piece. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Like in commit 44713b67 ("ipv4: Optimize flow initialization in output route lookup." we can optimize the on-stack flow setup to only initialize the members which are actually used. Otherwise we bzero the entire structure, then initialize explicitly the first half of it. Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Like in commit 44713b67 ("ipv4: Optimize flow initialization in output route lookup." we can optimize the on-stack flow setup to only initialize the members which are actually used. Otherwise we bzero the entire structure, then initialize explicitly the first half of it. Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 09 Mar, 2011 11 commits
-
-
Mario Schuknecht authored
In contrast to SIOCOUTQ which returns the amount of data sent but not yet acknowledged plus data not yet sent this patch only returns the data not sent. For various methods of live streaming bitrate control it may be helpful to know how much data are in the tcp outqueue are not sent yet. Signed-off-by: Mario Schuknecht <m.schuknecht@dresearch.de> Signed-off-by: Steffen Sledz <sledz@dresearch.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Create a common helper for this operation, since we do it identically in three spots. Suggested by Eric Dumazet. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amerigo Wang authored
V2: Move #ifdef CONFIG_PROC_FS into bonding.h, as suggested by David. bond_main.c is bloating, separate the procfs code out, move them to bond_procfs.c Signed-off-by: WANG Cong <amwang@redhat.com> Reviewed-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
This is now a run-time choice so that a single kernel can support both old and new generation ISI modems. Support for manually enabling the pipe flow is removed as it did not work properly, does not fit well with the socket API, and I am not aware of any use at the moment. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
This provides support for newer ISI modems with no need for the earlier experimental compile-time alternative choice. With this, we can now use the same kernel and userspace with both types of modems. This also avoids confusing two different and incompatible state machines, actively connected vs accepted sockets, and adds connection response error handling (processing "SYN/RST" of sorts). Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
User-space sometimes needs this information. In particular, the GPRS context or the AT commands pipe setups may use the pipe handle as a reference. This removes the settable pipe handle with CONFIG_PHONET_PIPECTRLR. It did not handle error cases correctly. Furthermore, the kernel *could* implement a smart scheme for allocating handles (if ever needed), but userspace really cannot. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
This moves most of the accept logic to process context like other socket stacks do. Then we can use a few more common socket helpers and simplify a bit. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
With the addition of the pipe controller, there is now quite a bit of repetitive code for small signaling messages. Lets factor it. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
In some cases, the Phonet pipe backlog callbacks returned negative errno instead of NET_RX_* values. In other cases, NET_RX_DROP was returned for invalid packets, even though it seems only intended for buffering problems (not for deliberately discarded packets). Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
Phonet assumes that packets are never dropped. We try our best to avoid this situation. But lets return ENOBUFS if queueing to the network device fails so that the caller knows things went wrong. Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rémi Denis-Courmont authored
The previous Phonet patch series introduced per-socket implicit destination (i.e. connect()). In that case, the destination socket address is NULL in the transmit function. However commit a8059512 ("Phonet: implement per-socket destination/peer address") is incomplete and would trigger a NULL dereference. (Fortunately, the code is not in released kernel, and in fact currently not reachable.) Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 08 Mar, 2011 21 commits
-
-
David S. Miller authored
If modifications on other cpus are ok, then modifications to the tree during lookup done by the local cpu are ok too. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Gospodarek authored
This commit: commit d7c8a29f Author: Emil Tantilov <emil.s.tantilov@intel.com> Date: Thu Mar 3 09:25:02 2011 +0000 ixgbe: improve logic in ixgbe_init_mbx_params_pf incorrectly added a line that accessed mbx->udelay. I'm sure the intent was mbx->usec_delay. This patch fixes the compilation error. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Korsgaard authored
The mv88e6060 uses either the lower 16 or upper 16 mii addresses, depending on the value of the EE_CLK/ADDR4 pin. Support both configurations by using the sw_addr setting as base address. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
-
David S. Miller authored
We have to use cfg->fc_scope not the final nh_scope value. Reported-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
When doing output route lookups, we have to select the source address if the user has not specified an explicit one. First, if the route has an explicit preferred source address specified, then we use that. Otherwise we search the route's outgoing interface for a suitable address. This search can be precomputed and cached at route insertion time. The only missing part is that we have to refresh this precomputed value any time addresses are added or removed from the interface, and this is accomplished by fib_update_nh_saddrs(). Signed-off-by: David S. Miller <davem@davemloft.net>
-
Emil Tantilov authored
Add the ability to set 100/F on x540. Fix reporting of advertised modes by adding check for phy.autoneg_advertised Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Use if/then instead of an all-inclusive case statement. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Add description for ixgbe_init_eeprom_params_X540 and whitespace fix. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
This patch enables flow control pause parameters auto-negotiation support to 82599 based 10G Base-T, backplane devices and multi-speed fiber optics modules at 1G speed Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Add defines to accumulate and display x540 PHY statistic counters on transmit/receive. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
The 82599 was not correctly having some of it's counters cleared for flow control. This change corrects that. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
This change cleans up several situations in which we were either stepping over possible errors, or calling initialization routines multiple times. Also includes whitespace fixes where applicable. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Yi Zou authored
Add support to the ndo_fcoe_ddp_target() to allow the Intel 82599 device to also provide DDP offload capability when the upper FCoE protocol stack is operating as a target. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Yi Zou authored
Add the new target ddp offload support ndo_fcoe_ddp_target(). Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Yi Zou authored
The Fiber Channel over Ethernet (FCoE) Direct Data Placement (DDP) can also be used for FCoE target, where the DDP used for read I/O on an initiator can be used on an FCoE target to speed up the write I/O to the target from the initiator. The added ndo_fcoe_ddp_target() works in the similar way as the existing ndo_fcoe_ddp_setup() to allow the underlying hardware set up the DDP context accordingly when it gets called from the FCoE target implementation on top the existing Open-FCoE fcoe/libfc protocol stack so without losing the ability to provide DDP for read I/O as an initiator, it can also provide DDP offload to the write I/O coming from the initiator as a target. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
In the previous commit: commit 5e655105 Author: Don Skidmore <donald.c.skidmore@intel.com> Date: Fri Feb 25 01:58:04 2011 +0000 ixgbe: add function pointer for semaphore function there was one release of the semaphore function call which did not get converted to a function pointer. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Carolyn Wyborny authored
This patch adds statistics output for OS2BMC feature which is configured by eeprom on capable devices. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
kernel build fails with: drivers/built-in.o: In function `e1000_lv_jumbo_workaround_ich8lan': (.text+0x3e7a8): undefined reference to `crc32_le' when CONFIG_CRC32 is not set or does not match the CONFIG_E1000E selection. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-