Define sam9n12 clocks and make use of them in peripheral definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This patch encloses sam9n12 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This patch removes the selection of AT91_USE_OLD_CLK when selecting
sam9x5 SoCs support. This will automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define sam9x5ek's main and slow crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This patch encloses sam9x5 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The tsadcc node is useless as it doesn't refer to anything and the touchscreen
is handled by the adc0 node.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel_tsadcc has been removed, stop selecting it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9rl and at91sam9rl based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

atmel_tsadcc is not allowing to use the remaining ADC channels while at91_adc
does. Completely switch to at91_adc and remove the tsadcc platform_data for
at91sam9g45 and at91sam9g45 based boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ADC clock needs to be defined to enable the at91_adc driver. It is defined
to the same speed that is used for atmel_tsadcc.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

That include file is now only used by the at91_adc driver, remove it from
include/mach for better driver separation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

at91_adc now supports reading a touchscreen for ADCs without a TSMR register.
Enable touchscreen support through at91_adc. This allows to use both a
touchscreen and the remaining ADC channel at the same time.

Also, lower the clock for the ADC as it allows to have more stable reads and
this is the speed used by atmel_tsadcc.
It lowers the maximum throughput rate from 440000 samples per second to 12958
samples per second. It shouldn't be an issue as the CPU is not able to keep up
reading samples at that frequency.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

num_channels and registers are not used anymore since they are defined inside
the driver and assigned by matching the id_table.

Also, struct at91_adc_reg_desc is now only used inside the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.

Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

num_channels and registers are not used anymore since they are defined inside
the at91_adc driver and assigned by matching the id_table.

Also, remove the mach/at91_adc.h include that is not necessary anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define at91sam9rlek crystal frequencies.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Move at91sam9rl SoC to the new main/slow clock model.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define at91sam9261ek main crystal frequency.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Jean-Jacques HIBLOT <jjhiblot@traphandler.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define crystal properties of sama5d3 xplained board.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define crystal frequencies of sama5d3xcm boards.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Replace the old main and clk definitions (fixed rate clk) by the new main and
slow clk subtree definition (ck = mux(rc_osc, osc)).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add slow clk, and slow oscillators documentation.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

AT91 slow clk is a clk multiplexer.

In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an oscillator
using an external crystal.

In other Socs (sam9260 family) the multiplexer source is hardcoded with
the OSCSEL signal.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Update main clk documentation to match main clk implementation rework.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

AT91 main clk is a clk multiplexer and not a simple fixed rate clk as
currently implemented.

In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an
oscillator using an external crystal.

In other Socs (sam9260, rm9200 families) the multiplexer source is
hardcoded to the external crystal oscillator.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This moves the <mach/gpio.h> header in the AT91 platform down
into the machine directory and removes the reliance on
MACH_NEED_GPIO_H from the AT91.

This does not move the platform to GENERIC_GPIO but localize
the remaining work to be done for this to the mach-at91
folder.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: adapt to newer kernel, add rsi-ews board]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This include file is about to disapear. In addition it is
useless for this code. So it is time to remove it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Brown <broonie@linaro.org>

Pull file locking change from Jeff Layton:
 "Only an email address change to the MAINTAINERS file"

* tag 'locks-v3.15-3' of git://git.samba.org/jlayton/linux:
  MAINTAINERS: email address change for Jeff Layton

Pull arm64 fixes from Catalin Marinas:
 "These are mostly arm64 fixes with an additional arm(64) platform fix
  for the initialisation of vexpress clocks (the latter only affecting
  arm64; the arch/arm64 code is SoC agnostic and does not rely on early
  SoC-specific calls)

   - vexpress platform clocks initialisation moved earlier following the
     arm64 move of of_clk_init() call in a previous commit
   - Default DMA ops changed to non-coherent to preserve compatibility
     with 32-bit ARM DT files.  The "dma-coherent" property can be used
     to explicitly mark a device coherent.  The Applied Micro DT file
     has been updated to avoid DMA cache maintenance for the X-Gene SATA
     controller (the only arm64 related driver with such assumption in
     -rc mainline)
   - Fixmap correction for earlyprintk
   - kern_addr_valid() fix for huge pages"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  vexpress: Initialise the sysregs before setting up the clocks
  arm64: Mark the Applied Micro X-Gene SATA controller as DMA coherent
  arm64: Use bus notifiers to set per-device coherent DMA ops
  arm64: Make default dma_ops to be noncoherent
  arm64: fixmap: fix missing sub-page offset for earlyprintk
  arm64: Fix for the arm64 kern_addr_valid() function

Pull SCSI fixes from James Bottomley:
 "This is two patches both fixing bugs in drivers (virtio-scsi and
  mpt2sas) causing an oops in certain circumstances"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] virtio-scsi: Skip setting affinity on uninitialized vq
  [SCSI] mpt2sas: Don't disable device twice at suspend.