Although this driver gives the framebuffer layer a different
size for the framebuffer it uses the entire aperture PCI BAR
size for the MTRR. Since the framebuffer is included in that
range and MTRR was used on the entire PCI BAR WC will have
been preferred on that range as well. This propagates the
WC preference on the same entire PCI BAR.

Convert the driver from using the x86 specific MTRR code to
the architecture agnostic arch_phys_wc_add(). arch_phys_wc_add()
will avoid MTRR if write-combining is available, in order to
take advantage of that also ensure the ioremap'd area is requested
as write-combining.

There are a few motivations for this:

a) Take advantage of PAT when available

b) Help bury MTRR code away, MTRR is architecture specific and on
   x86 its replaced by PAT

c) Help with the goal of eventually using _PAGE_CACHE_UC over
   _PAGE_CACHE_UC_MINUS on x86 on ioremap_nocache() (see commit
   de33c442 titled "x86 PAT: fix performance drop for glx,
   use UC minus for ioremap(), ioremap_nocache() and
   pci_mmap_page_range()")

The conversion done is expressed by the following Coccinelle
SmPL patch, it additionally required manual intervention to
address all the #ifdery and removal of redundant things which
arch_phys_wc_add() already addresses such as verbose message
about when MTRR fails and doing nothing when we didn't get
an MTRR.

@ mtrr_found @
expression index, base, size;
@@

-index = mtrr_add(base, size, MTRR_TYPE_WRCOMB, 1);
+index = arch_phys_wc_add(base, size);

@ mtrr_rm depends on mtrr_found @
expression mtrr_found.index, mtrr_found.base, mtrr_found.size;
@@

-mtrr_del(index, base, size);
+arch_phys_wc_del(index);

@ mtrr_rm_zero_arg depends on mtrr_found @
expression mtrr_found.index;
@@

-mtrr_del(index, 0, 0);
+arch_phys_wc_del(index);

@ mtrr_rm_fb_info depends on mtrr_found @
struct fb_info *info;
expression mtrr_found.index;
@@

-mtrr_del(index, info->fix.smem_start, info->fix.smem_len);
+arch_phys_wc_del(index);

@ ioremap_replace_nocache depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap_nocache(base, size);
+info->screen_base = ioremap_wc(base, size);

@ ioremap_replace_default depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap(base, size);
+info->screen_base = ioremap_wc(base, size);

Generated-by: Coccinelle SmPL
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Convert the driver from using the x86 specific MTRR code to
the architecture agnostic arch_phys_wc_add(). arch_phys_wc_add()
will avoid MTRR if write-combining is available, in order to
take advantage of that also ensure the ioremap'd area is requested
as write-combining.

There are a few motivations for this:

a) Take advantage of PAT when available

b) Help bury MTRR code away, MTRR is architecture specific and on
   x86 its replaced by PAT

c) Help with the goal of eventually using _PAGE_CACHE_UC over
   _PAGE_CACHE_UC_MINUS on x86 on ioremap_nocache() (see commit
   de33c442 titled "x86 PAT: fix performance drop for glx,
   use UC minus for ioremap(), ioremap_nocache() and
   pci_mmap_page_range()")

The conversion done is expressed by the following Coccinelle
SmPL patch, it additionally required manual intervention to
address all the #ifdery and removal of redundant things which
arch_phys_wc_add() already addresses such as verbose message
about when MTRR fails and doing nothing when we didn't get
an MTRR.

@ mtrr_found @
expression index, base, size;
@@

-index = mtrr_add(base, size, MTRR_TYPE_WRCOMB, 1);
+index = arch_phys_wc_add(base, size);

@ mtrr_rm depends on mtrr_found @
expression mtrr_found.index, mtrr_found.base, mtrr_found.size;
@@

-mtrr_del(index, base, size);
+arch_phys_wc_del(index);

@ mtrr_rm_zero_arg depends on mtrr_found @
expression mtrr_found.index;
@@

-mtrr_del(index, 0, 0);
+arch_phys_wc_del(index);

@ mtrr_rm_fb_info depends on mtrr_found @
struct fb_info *info;
expression mtrr_found.index;
@@

-mtrr_del(index, info->fix.smem_start, info->fix.smem_len);
+arch_phys_wc_del(index);

@ ioremap_replace_nocache depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap_nocache(base, size);
+info->screen_base = ioremap_wc(base, size);

@ ioremap_replace_default depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap(base, size);
+info->screen_base = ioremap_wc(base, size);

Generated-by: Coccinelle SmPL
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This driver never removed the MTRRs. Fix that.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Convert the driver from using the x86 specific MTRR code to
the architecture agnostic arch_phys_wc_add(). arch_phys_wc_add()
will avoid MTRR if write-combining is available, in order to
take advantage of that also ensure the ioremap'd area is requested
as write-combining.

There are a few motivations for this:

a) Take advantage of PAT when available

b) Help bury MTRR code away, MTRR is architecture specific and on
   x86 its replaced by PAT

c) Help with the goal of eventually using _PAGE_CACHE_UC over
   _PAGE_CACHE_UC_MINUS on x86 on ioremap_nocache() (see commit
   de33c442 titled "x86 PAT: fix performance drop for glx,
   use UC minus for ioremap(), ioremap_nocache() and
   pci_mmap_page_range()")

The conversion done is expressed by the following Coccinelle
SmPL patch, it additionally required manual intervention to
address all the #ifdery and removal of redundant things which
arch_phys_wc_add() already addresses such as verbose message
about when MTRR fails and doing nothing when we didn't get
an MTRR.

@ mtrr_found @
expression index, base, size;
@@

-index = mtrr_add(base, size, MTRR_TYPE_WRCOMB, 1);
+index = arch_phys_wc_add(base, size);

@ mtrr_rm depends on mtrr_found @
expression mtrr_found.index, mtrr_found.base, mtrr_found.size;
@@

-mtrr_del(index, base, size);
+arch_phys_wc_del(index);

@ mtrr_rm_zero_arg depends on mtrr_found @
expression mtrr_found.index;
@@

-mtrr_del(index, 0, 0);
+arch_phys_wc_del(index);

@ mtrr_rm_fb_info depends on mtrr_found @
struct fb_info *info;
expression mtrr_found.index;
@@

-mtrr_del(index, info->fix.smem_start, info->fix.smem_len);
+arch_phys_wc_del(index);

@ ioremap_replace_nocache depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap_nocache(base, size);
+info->screen_base = ioremap_wc(base, size);

@ ioremap_replace_default depends on mtrr_found @
struct fb_info *info;
expression base, size;
@@

-info->screen_base = ioremap(base, size);
+info->screen_base = ioremap_wc(base, size);

Generated-by: Coccinelle SmPL
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use kernel.h macro definition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use kernel.h macro definition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use kernel.h macro definition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The logical not needs to be done after the bit masking.

Fixes: a3998fe03e87 ("fbdev: ssd1307fb: Unify init code and obtain
hw specific bits from DT")
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The h3 LCD driver fails to link when tps65010 is configured
as a loadable module:

drivers/built-in.o: In function `h3_panel_disable':
debugfs.c:(.text+0x206ac): undefined reference to `tps65010_set_gpio_out_value'
debugfs.c:(.text+0x206cc): undefined reference to `tps65010_set_gpio_out_value'
drivers/built-in.o: In function `h3_panel_enable':
debugfs.c:(.text+0x206e0): undefined reference to `tps65010_set_gpio_out_value'
debugfs.c:(.text+0x20704): undefined reference to `tps65010_set_gpio_out_value'

This clarifies the dependency so we can only select it if
the dependnecy is built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The error handling got shifted down a few lines from where it was
supposed to be for some reason.

Fixes: a14a7ba8cb0f ('fbdev: ssd1307fb: add backlight controls for setting the contrast')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch adds ssd1307fb_blank() to make the framebuffer capable
of blanking.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The backlight class is used to create userspace handles for
setting the OLED contrast.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch turns off the display when the driver is unloaded.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch adds the module parameter "refreshrate" to set delay for the
deferred io. The refresh rate is given in units of Hertz. The default
refresh rate is 1 Hz. The refresh rate set through the newly introduced
parameter applies to all instances of the driver and for now it is not
possible to change it individually.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch adds support for the SSD1305 OLED controller.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch updates the in tree-users of the SSD1306 controller for using
the newly introduced DT properties.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The 130X controllers are very similar from the configuration point of view.
The configuration registers for the SSD1305/6/7 are bit identical (except the
the VHCOM register and the the default values for clock setup register). This
patch unifies the init code of the controller and adds hardware specific
properties to DT that are needed to correctly initialize the device.

The SSD130X can be wired to the OLED panel in various ways. Even for the
same controller this wiring can differ from one display module to another
and can not be probed by software. The added DT properties reflect these
hardware decisions of the display module manufacturer.
The 'com-sequential', 'com-lrremap' and 'com-invdir' values define different
possibilities for the COM signals pin configuration and readout direction
of the video memory. The 'segment-no-remap' allows the inversion of the
memory-to-pin mapping ultimately inverting the order of the controllers
output pins. The 'prechargepX' values need to be adapted according to the
capacitance of the OLEDs pixel cells.

So far these hardware specific bits are hard coded in the init code, making
the driver usable only for one certain wiring of the controller. This patch
makes the driver usable with all possible hardware setups, given a valid hw
description in DT. If these values are not set in DT the default values,
as they are set in the ssd1307 init code right now, are used. This implies
that without the corresponding DT property "segment-no-remap" the segment
remap of the ssd130X controller gets activated. Even though this is not the
default behaviour according to the datasheet it maintains backward
compatibility with older DTBs.

Note that the SSD1306 does not seem to be using the configuration written to
the registers at all. Therefore this patch does not try to maintain these
values without changes in DT. For reference an example is added to the DT
bindings documentation that reproduces the configuration that is set in the
current init code.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Tested-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch adds the solomon prefix for Solomon Systech Limited.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Currently the videomemory is allocated by kmalloc, making it a memory
region that is not necessarily page aligend. This leads to problems
upon mmap call, where the video memory's address gets aligned to the
next page boundary. The result is that the userspace program that issued
the mmap call is not able to access the video memory from the start to
the next page boundary.

This patch changes the allocation of the video memory to use
__get_free_pages() in order to obtain memory that is aligned
to page boundaries.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

the smem_start pointer of the framebuffer info struct needs to hold the
physical address rather than the logical address. Right now the logical
address returned by kmalloc is stored. This patch converts this address
to a physical address and thus fixes a driver crash on mmaping the
framebuffer memory due to an access to the wrong memory address.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The LCDIF engines embedded in i.MX6sl and i.MX6sx SoCs need the axi clock
as the engine's system clock.  The clock should be enabled when accessing
LCDIF registers, otherwise the kernel would hang up.  We should also keep
the clock enabled when the engine is being active to scan out frames from
memory.  This patch makes sure the axi clock is enabled when accessing
registers so that the kernel hang up issue can be fixed.
Reported-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

CONFIG_FB_DEFERRED_IO is defined as bool while CONFIG_FB is defined as
tristate. Currently fb_defio.o is linked into the kernel image even if
CONFIG_FB=m.

I fix this by updating the Makefile to link fb_defio.o into fb.o and thus
go into one place with the other core framebuffer code.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Pull ext4 fixes from Ted Ts'o:
 "Some miscellaneous bug fixes and some final on-disk and ABI changes
  for ext4 encryption which provide better security and performance"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix growing of tiny filesystems
  ext4: move check under lock scope to close a race.
  ext4: fix data corruption caused by unwritten and delayed extents
  ext4 crypto: remove duplicated encryption mode definitions
  ext4 crypto: do not select from EXT4_FS_ENCRYPTION
  ext4 crypto: add padding to filenames before encrypting
  ext4 crypto: simplify and speed up filename encryption

Pull drm fixes from Dave Airlie:
 "One intel fix, one rockchip fix, and a bunch of radeon fixes for some
  regressions from audio rework and vm stability"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915/chv: Implement WaDisableShadowRegForCpd
  drm/radeon: fix userptr return value checking (v2)
  drm/radeon: check new address before removing old one
  drm/radeon: reset BOs address after clearing it.
  drm/radeon: fix lockup when BOs aren't part of the VM on release
  drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
  drm/radeon: adjust pll when audio is not enabled
  drm/radeon: only enable audio streams if the monitor supports it
  drm/radeon: only mark audio as connected if the monitor supports it (v3)
  drm/radeon/audio: don't enable packets until the end
  drm/radeon: drop dce6_dp_enable
  drm/radeon: fix ordering of AVI packet setup
  drm/radeon: Use drm_calloc_ab for CS relocs
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915/chv: Implement WaDisableShadowRegForCpd

one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
  drm/rockchip: fix error check when getting irq
  MAINTAINERS: add entry for Rockchip drm drivers

Pull SCSI fixes from James Bottomley:
 "This is three logical fixes (as 5 patches).

  The 3ware class of drivers were causing an oops with multiqueue by
  tearing down the command mappings after completing the command (where
  the variables in the command used to tear down the mapping were
  no-longer valid).  There's also a fix for the qnap iscsi target which
  was choking on us sending it commands that were too long and a fix for
  the reworked aha1542 allocating GFP_KERNEL under a lock"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: fix command completion race
  3w-xxxx: fix command completion race
  3w-sas: fix command completion race
  aha1542: Allocate memory before taking a lock
  SCSI: add 1024 max sectors black list flag

Pull slave dmaengine fixes from Vinod Koul:
 "Here are the fixes in dmaengine subsystem for rc2:

   - privatecnt fix for slave dma request API by Christopher

   - warn fix for PM ifdef in usb-dmac by Geert

   - fix hardware dependency for xgene by Jean"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: increment privatecnt when using dma_get_any_slave_channel
  dmaengine: xgene: Set hardware dependency
  dmaengine: usb-dmac: Protect PM-only functions to kill warning

Pull powerpc fixes from Michael Ellerman:
 - build fix for SMP=n in book3s_xics.c
 - fix for Daniel's pci_controller_ops on powernv.
 - revert the TM syscall abort patch for now.
 - CPU affinity fix from Nathan.
 - two EEH fixes from Gavin.
 - fix for CR corruption from Sam.
 - selftest build fix.

* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/powernv: Restore non-volatile CRs after nap
  powerpc/eeh: Delay probing EEH device during hotplug
  powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
  powerpc/pseries: Correct cpu affinity for dlpar added cpus
  selftests/powerpc: Fix the pmu install rule
  Revert "powerpc/tm: Abort syscalls in active transactions"
  powerpc/powernv: Fix early pci_controller_ops loading.
  powerpc/kvm: Fix SMP=n build error in book3s_xics.c

The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.

Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>

fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.

The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.

At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.

When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.

For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.

This problem can be easily reproduced by running the following xfs_io.

xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
          -c "falloc 0 131072" \
          -c "pwrite -S 0xbb 65536 2048" \
          -c "fsync" /mnt/test/fff

echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff

This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit 3edc18d8 and commit f542fb.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...

Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.

This makes it clear that Michael is in charge.  He's good, but having
me watch over his shoulder won't help.

Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull Ceph RBD fix from Sage Weil.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: end I/O the entire obj_request on error

If we don't do that, then the poison value is left in the ->pprev
backlink.

This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>