There is frequent downlink throughput drop to 0 when operating
at the signal level between -42dBm to -53dBm. This has been root
caused to the delay in releasing pending a-mpdu subframes in
reorder buffer. Right now the timeout value is 400ms, there
is also a race condition where timeout handler can be delayed
to run at an extra timeout interval. This patch reduces the
timout interval to reasonable 100ms and makes sure releasing
pending frames are not skipped in the timeout handler by removing
the flag (rxtid->progress) which can delay the timeout logic.
Reported-by: Yu Yanzhi <yanzhiy@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There are many places where tid data are accessed without
the lock (rxtid->lock), this can lead to a race condition
when the timeout handler for aggregatin reorder and the
receive function are getting executed at the same time.
Fix this race, but still there are races which can not
be fixed without rewriting the whole aggregation reorder
logic, for now fix the obvious ones.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch adds support for dtim_period configuration in beacon.

kvalo: add a comment about ignoring the error, use vif_idx,
add \n to the warning message
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Messages without newlines can be interleaved.
Avoid this by adding terminations.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In virtual interface structure, for each band separate ht cap
is needed. so that one can disable or enable ht capability band
wise.
This will fix the following issue:

1) Disable 11n from supplicant and start a P2P GO.
2) In beacon frames no HT-CAP IE is seen which is expected.
3) Now remove the P2P GO and kill the supplicant.
4) Beacon stops
5) Now using iw  associate to an external AP in 5 GHZ
6) In 5 GHZ no HT IE going in assoc request but
when  associated in 2.4 GHZ can see HT IES over the air
in assoc request.

In the code for del_beacon in cfg80211.c,set_ht_cap is being
called first for 2.4 GHZ and then for 5 GHZ. When  called
for the first time for 2.4 GHZ the enable flag will be set to true
and so when called for the second time for 5 GHZ it just returns
after checking the flag.

Also using this one can have different HT capabilities
per band (for example one may decide not to use 20/40 in 2.4 GHZ
but use it in 5 GHZ). So maintaining a single context is not ok.
it is true for even the enable/disable flag and other HT
capabilities as well
Signed-off-by: Kiran Reddy <c_lreddy@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add missing ZERO (x%x to 0x%x) in the format specifier
while printing hex value in htc module.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

No need to clear requested memory after allocating new SKB
with help of ath6kl_wmi_get_new_buf(). This clear part is
already taken care in ath6kl_wmi_get_new_buf().

Found this on code review.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Tx legacy and mcs rateset can configured using iw for
2.4 and 5 bands.  Add support for the same in driver.

kvalo: add an enum for the hw flags and rename the flag accordingly,
rename ath6kl_cfg80211_set_bitrate_mask() to a shorter version to make
it easier to indent
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

GPIO pin 9 also needs to be configured along with other gpio
pins to avoid sdio crc errors. I've not experienced any issue
with missing this particular gpio pin configuration, found dunring
code review. This can potentially improve rx performance.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl would issue a wmi disconnect command in response to a remote
disconnect and return early without notifying cfg80211, only sending a
cfg80211_disconnected (with reason code always 3) in response to the
second disconnect firmware event.

Pass the right reason code to cfg80211 on the first disconnect instead.

This fixes at least one bug where a p2p client would stop trying to
connect after receiving a stale RSN deauth which was reported to
cfg80211 as GO leaving BSS.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Scheduled scan implementation was only taking probed list into
consideration. The matched list was dropped. This would cause
FW not to report the AP as the list never had that AP's SSID
populated. This was causing long connection time when supplicant
would just issue a wild card SSID in probed list. As a part of
this implementation, ath6kl driver would create a complete list
by taking both probed and matched list and pass it to FW. FW would
probe for the SSID that it needs to and would match against the
relevant SSIDS that is been configured.

kvalo: whitespace changes, less indentation in the for loop, use ++
Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Enable enhanced bmiss detection if the firmware supports it. This
feature is only enabled on some firmwares since it comes with a power
cost.

Also add a few missing command ids to keep the enums straight.

kvalo: fix a compiler with ath6kl_err(), add few empty lines
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Infrastructure to enable Multicast WOW support based on
firmware capability added to the driver.This enables
different customers or chips to control this feature based
on firmware capability.

kvalo: Firmware capability infrastructure for multicast wow feature,
indetation fixes.
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The currently used firmware images support 16 SSIDs in the scan
request (indexes 0..15), so update the host driver to use the same
limit to allow some more SSIDs to be scanned per request. In addition,
change the max-index to max-SSIDs to make it easier to understand the
implementation and fix couple of off-by-one checks that could limit
the maximum number of entries too strictly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Send the EAPOL and management frames in the same AC_VO queue. The issue
happens when the AP supports QOS, the management frames are sent to AC_VO
queue and EAP frame goes to AC_BE queue. Even though the EAP frame is
queued before the DEAUTH management frame, as they are queued on different
h/w queues, order of delivery between these frames cannot be controlled.

This fixes the connection failure seen in P2P case.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Return status of ath6kl_htc_tx_issue() is ignored in
ath6kl_htc_tx_from_queue(), but failed tx packet is
is not cleaned up. To fix memory leak in this case, call
completion with error. Also, throw an error debug message
when tx fails in ath6kl_sdio_write_async() due to shortage
in bus request buffer.

kvalo: change the error message to WARN_ON_ONCE()
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There are few cases where the tx skb is dropped but netstats is
not updated, fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

On the htc mbox layer, it will assign each endpoint (AC) with a
different Tx-packet-drop threshold, so lower priority AC is more
likely to drop packets and the cookies become more available to higher
priority AC.

On the htc pipe layer, assign the tx packet drop threshold as well, it
will let AC to drop packets when cookies below the tx packet drop
threshold.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When a STA sends huge BK QoS data frame first and then sends BE/VI/VO
QoS data frame, the corresponding throughput becomes much lower than
that without sends BK QoS data frame before.

The root cause is that when station send BK stream, the tx credits of
BK stream don't return back to higher priority QoS stream such as BE,
VI, and VO stream. This patch will handle BK stream properly, when
there is higher priority QoS stream, it will seek tx credits from BK
stream properly.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

bss filter is configured to allow the frames from all the bss other
than the currenly connected one, this is done when a scan is requested
in connected state. There is no reason to filter out the currently
connected bss, configure the filter to allow all the bss. This would
fix the reporting of stale rssi of the current bss while scanning.
Reported-by: Naveen singh <navesing@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

With firmwares which do not support rsn capability override
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) from host would
cause 4-way handshake failure when HT cap is advertised.
To fix this, do not advertise HT cap with cfg80211 for
those fw.

kvalo: fix a checkpatch warning
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.

Multicast requirements
 - Enable forward all multicast packets(no filtering) in
      non suspend mode.
 - Enable multicast filtering in wow suspend mode for both
      AP and CLIENT.

kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The patch "ath6kl: support fw reporting phy capabilities" gave the
firmware the ability to disable certain wiphy supported bands. Check if
this is the case in ath6kl_wmi_beginscan_cmd to avoid dereferencing a
NULL pointer.

kvalo: change the patch so that there's no code between declarations
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Do not assume anyone before us includes it for us.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Complete the waiting fwlog_block_read on debugfs cleanup, otherwise
userspace and module unload might softlock.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is supposed to be pushed in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The original conditions are always true.  I think && was intended here,
but I don't have the hardware to test.  Could you take a look?

kvalo: Chilam confirmed that the fix is valid
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: If wow deepsleep pno suspend failure driver will choose cutpower.
in this scenario MMC_PM_KEEP_POWER should be cleared so that mmc will power
off the ar6000

kvalo: remove extra parenthesis
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.

Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.

In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.

kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

We can remove the NULL check here.  It triggers a Smatch warning because
list_first_entry() never is NULL and people who check for it normally
intend to check for list_empty() instead.  In these cases however,
we've already verified that the lists are not empty.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

kvalo: do the same changes for ar6004 hw1.2 as well

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.

kvalo: fix commit log
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

System crash because of NULL pointer reference due to
cleanup_scatter is not implemented for USB.
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>