- 10 Mar, 2011 40 commits
-
-
Lars Ellenberg authored
The "lazy writeout" of cleared bitmap pages happens during resync, and should happen again once the resync finishes cleanly, or is aborted. If resync finished cleanly, or was aborted because of peer disk failure, we trigger the writeout from worker context in the after state change work. If resync was aborted because of connection failure, we should not immediately trigger bitmap writeout, but rather postpone the writeout to after the connection cleanup happened. We now do it in the receiver context from drbd_disconnect(). If resync was aborted because of local disk failure, well, there is nothing to write to anymore. Signed-off-by:
Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by:
Lars Ellenberg <lars.ellenberg@linbit.com>
-
Lars Ellenberg authored
This is a minor optimization and cleanup, and also considerably reduces some harmless (but noisy) race with the connection cleanup code. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Philipp Reisner authored
Signed-off-by:
-
Philipp Reisner authored
The assert in drbd_req.c:755 forces us to have only requests of one kind in an epoch. The two kinds we distinguish here are: local-only or mirrored. Signed-off-by:
-
Philipp Reisner authored
Protocol A has no P_WRITE_ACKs, but has P_NEG_ACKs. The master bio might already be completed, therefore the request is no longer in the collision hash. => Do not try to validate block_id as request In Protocol B we might already have got a P_RECV_ACK but then get a P_NEG_ACK after wards. Signed-off-by:
-
Philipp Reisner authored
The point is that drbd_disconnect() can be called with a cstate of WFConnection. That happens if the user issues "drbdsetup disconnect" while the drbd_connect() function executes. Then drbdd_init() will call drbdd(), which in turn will return without receiving any packets. Then drbdd_init() will end up calling drbd_disconnect() with a cstate of WFConnection. Bottom line: This assertion is wrong as it is, and we do not see value in fixing it. => Removing it. Signed-off-by:
-
Philipp Reisner authored
Signed-off-by:
-
Philipp Reisner authored
The test if rs_pending_cnt == 0 was too weak. Using Test for unacked_cnt == 0 instead. Moved that into the worker. Since unacked_cnt gets already increased when an P_RS_DATA_REQ comes in. Also using a timer to make Ahead -> SyncSource -> Ahead cycles slower... Signed-off-by:
-
Philipp Reisner authored
Signed-off-by:
-
Philipp Reisner authored
See also commit from 2009-08-15 "drbd_uuid_compare(): Do not full sync in case a P_SYNC_UUID packet gets lost." We saw cases where the History UUIDs where not as expected. So the detection of the special case did not trigger. With the sync UUID no longer being a random number, but deducible from the previous bitmap UUID, the detection of this special case becomes more reliable. The SyncUUID now is the previous bitmap UUID + 0x1000000000000. Rule 5a: Cs = H1p & H1p + Offset = Bp Connection was lost before SyncUUID Packet came through. Corrent (peer) UUIDs: Bp = H1p H1p = H2p H2p = 0 Become Sync target. Rule 7a: Cp = H1s & H1s + Offset = Bs Connection was lost before SyncUUID Packet came through. Correct (own) UUIDs: Bs = H1s H1s = H2s H2s = 0 Become Sync source. Signed-off-by:
-
Philipp Reisner authored
Signed-off-by:
-
Andreas Gruenbacher authored
Signed-off-by:
-
Philipp Reisner authored
Besides removed a few lines of code, this moves the inspection of the state from before the queuing process to after the queuing. I.e. more closely to the actual invocation of the work. Signed-off-by:
-
Philipp Reisner authored
We may not get from SyncSource to Ahead if we have sent some P_RS_DATA_REPLY packets to the peer and are waiting for P_WRITE_ACK. Again, this is not relevant for proper tuned systems, but makes sure that the not-tuned system does not get diverging bitmaps. Signed-off-by:
-
Philipp Reisner authored
When the sync source node replies to a P_RS_DATA_REQUEST packet when it is already in ahead mode. I.e. those two packets crossed each other on the wire, that may lead to diverging bitmaps. This never happens in a well-tuned-system. In a well-tuned- system the resync controller has reduced the resync speed to zero long before we got into ahead-mode. But we have to be prepared for the not-well-tuned-system of course as well. Because -> diverging bitmaps = non terminating resync. Signed-off-by:
-
Philipp Reisner authored
Create a new barrier when leaving the AHEAD mode. Otherwise we trigger the assertion in req_mod(, barrier_acked) D_ASSERT(req->rq_state & RQ_NET_SENT); The new barrier is created by recycling the newest existing one. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Philipp Reisner authored
When on-no-data-accessible is set to suspend-io, also consider that a Primary, SyncTarget node losses its connection. Signed-off-by:
-
Lars Ellenberg authored
I run into something declaring itself as "spinlock deadlock", BUG: spinlock lockup on CPU#1, kjournald/27816, ffff88000ad6bca0 Pid: 27816, comm: kjournald Tainted: G W 2.6.34.6 #2 Call Trace: <IRQ> [<ffffffff811ba0aa>] do_raw_spin_lock+0x11e/0x14d [<ffffffff81340fde>] _raw_spin_lock_irqsave+0x6a/0x81 [<ffffffff8103b694>] ? __wake_up+0x22/0x50 [<ffffffff8103b694>] __wake_up+0x22/0x50 [<ffffffffa07ff661>] bm_async_io_complete+0x258/0x299 [drbd] but the call traces do not fit at all, all other cpus are cpu_idle. I think it may be this race: drbd_bm_write_page wait_queue_head_t io_wait; atomic_t in_flight; bm_async_io submit_bio bm_async_io_complete if (atomic_dec_and_test(in_flight)) wait_event(io_wait, atomic_read(in_flight) == 0) return wake_up(io_wait) The wake_up now accesses the wait_queue_head_t spinlock, which is no longer valid, since the stack frame of drbd_bm_write_page has been clobbered now. Fix this by using struct completion, which does both the condition test as well as the wake_up inside its spinlock, so this race cannot happen. Signed-off-by:
-
Lars Ellenberg authored
Even though we now track the need for bitmap writeout per bitmap page, there is no need to trigger the writeout while a resync is going on. Once the resync is finished (or aborted), we trigger bitmap writeout anyways. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Lars Ellenberg authored
We expect changes to a bitmap page in drbd_bm_write_page, that's why we submit a copy page. If a page changes during global writeout, that would be unexpected, and reason to warn, though. Also, often page writeout can be skipped (on activity log transactions during normal operation, for example), no need to log that everytime. Signed-off-by:
-
Lars Ellenberg authored
To improve the latency of IO requests during bitmap exchange, we recently allowed writes while waiting for the bitmap, sending "set out-of-sync" information packets for any newly dirtied bits. We have to make sure that the new resync-uuid does not overtake these "set oos" packets. Once the resync-uuid is received, the sync target starts the resync process, and expects the bitmap to only be cleared, not re-set. If we use this protocol extension, we queue the generation and sending of the resync-uuid on the worker, which naturally serializes with all previously queued packets. Signed-off-by:
-
Lars Ellenberg authored
We expect to only receive the recently introduced "set out of sync" packets in specific states. If we receive them in different states, that may confuse the resync process to the point where it won't terminate, or think it made negative progress. Signed-off-by:
-
Philipp Reisner authored
Signed-off-by:
-
Lars Ellenberg authored
If drbd used to have crypto digest algorithms configured, then is being unconfigured (but not unloaded), it frees the algorithms, but does not reset the config. If it then is reconfigured to use the very same algorithm, it "forgot" to re-allocate the algorithms, thinking that the config has not changed in that aspect. It will then Oops on the first attempt to actually use those algorithms. Fix this by resetting the config to defaults after cleanup. Signed-off-by:
-
Lars Ellenberg authored
We must not call it directly from resync_finished, as we may be in either receiver or worker context there. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Lars Ellenberg authored
Long time ago, we had paranoia code in the bitmap that allocated one extra word, assigned a magic value, and checked on every occasion that the magic value was still unchanged. That debug code is unused, the extra long word complicates code a bit. Get rid of it. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Lars Ellenberg authored
When we set or clear bits in a bitmap page, also set a flag in the page->private pointer. This allows us to skip writes of unchanged pages. Signed-off-by:
-
Lars Ellenberg authored
Our on-disk bitmap is a little endian bitstream. Up to now, we have stored the in-core copy of that in native endian, applying byte order conversion when necessary. Instead, keep the bitmap pages little endian, as they are read from disk, and use the generic_*_le_bit family of functions. Signed-off-by:
-
Lars Ellenberg authored
We trusted the on-disk bitmap to have unused bits cleared. In case that is not true for whatever reason, and we take a code path where the unused bits don't get cleared elsewhere (bm_clear_surplus is not called), we may miscount the bits, and get confused during resync, waiting for bits to get cleared that we don't even use: the resync process would not terminate. Fix this by masking out unused bits in __bm_count_bits. Signed-off-by:
-
Andreas Gruenbacher authored
The old name is confusing: the function does not increment anything. Also rename _inc_ap_bio_cond to inc_ap_bio_cond: there is no need for an underscore. Finally, make it clear that these functions return boolean values. Signed-off-by:
-
Andreas Gruenbacher authored
I guess bitmap I/O errors are supposed to cause drbd_determin_dev_size to return dev_size_error. Signed-off-by:
-
Andreas Gruenbacher authored
Signed-off-by:
-
Andreas Gruenbacher authored
Signed-off-by:
-
Andreas Gruenbacher authored
Signed-off-by:
-
