- 09 Mar, 2015 3 commits
-
-
Valentin Rothberg authored
The IRQF_DISABLED is a NOOP and scheduled to be removed. According to commit e58aa3d2 ("genirq: Run irq handlers with interrupts disabled") running IRQ handlers with interrupts enabled can cause stack overflows when the interrupt line of the issuing device is still active. This patch removes using this deprecated flag and additionally removes redundantly setting IRQF_SHARED for isp1760_udc_register(). Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Arnd Bergmann authored
A recent bug fix I did that was marked for stable backports introduced a slightly wrong dependency on CONFIG_OMAP_CONTROL_PHY. I was missing the fact that the PHY driver already stubs out the omap_control_usb_set_mode, and we only need to add a dependency to prevent the musb-omap2430 driver from being built-in when the phy driver is a loadable module, but we should not prevent it from being built altogether when the phy driver is disabled. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: ca784be3 ("usb: start using the control module driver") Cc: <stable@vger.kernel.org> # v3.9+ Acked-by: Acked-by: Pavel Machek <pavel@ucw.cz> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Sudeep Holla authored
Use spin_{un,}lock_irq{save,restore} in isp1760_udc_{start,stop} to prevent following potentially deadlock scenario between isp1760_udc_{start,stop} and isp1760_udc_irq : ================================= [ INFO: inconsistent lock state ] 4.0.0-rc2-00004-gf7bb2ef60173 #51 Not tainted --------------------------------- inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. in:imklog/2118 [HC1[1]:SC0[0]:HE0:SE1] takes: (&(&udc->lock)->rlock){?.+...}, at: [<c0397a93>] isp1760_udc_irq+0x367/0x9dc {HARDIRQ-ON-W} state was registered at: [<c05135b3>] _raw_spin_lock+0x23/0x30 [<c0396b87>] isp1760_udc_start+0x23/0xf8 [<c039dc21>] udc_bind_to_driver+0x71/0xb0 [<c039de4f>] usb_gadget_probe_driver+0x53/0x9c [<bf80d0df>] usb_composite_probe+0x8a/0xa4 [libcomposite] [<bf8311a7>] 0xbf8311a7 [<c00088c5>] do_one_initcall+0x8d/0x17c [<c050b92d>] do_init_module+0x49/0x148 [<c0087323>] load_module+0xb7f/0xbc4 [<c0087471>] SyS_finit_module+0x51/0x74 [<c000d8c1>] ret_fast_syscall+0x1/0x68 irq event stamp: 4966 hardirqs last enabled at (4965): [<c05137df>] _raw_spin_unlock_irq+0x1f/0x24 hardirqs last disabled at (4966): [<c00110b3>] __irq_svc+0x33/0x64 softirqs last enabled at (4458): [<c0023475>] __do_softirq+0x23d/0x2d0 softirqs last disabled at (4389): [<c002380b>] irq_exit+0xef/0x15c other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&udc->lock)->rlock); <Interrupt> lock(&(&udc->lock)->rlock); *** DEADLOCK *** 1 lock held by in:imklog/2118: #0: (&f->f_pos_lock){+.+.+.}, at: [<c010a101>] __fdget_pos+0x31/0x34 Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
- 08 Mar, 2015 7 commits
-
-
Linus Torvalds authored
-
Al Viro authored
POLL_OUT isn't what callers of ->poll() are expecting to see; it's actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap bit... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@vger.kernel.org Cc: Bruce Fields <bfields@fieldses.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB fixes from Greg KH: "Here's a round of USB fixes for 4.0-rc3. Nothing major, the usual gadget, xhci and usb-serial fixes and a few new device ids as well. All have been in linux-next successfully" * tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits) xhci: Workaround for PME stuck issues in Intel xhci xhci: fix reporting of 0-sized URBs in control endpoint usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards USB: ch341: set tty baud speed according to tty struct USB: serial: cp210x: Adding Seletek device id's USB: pl2303: disable break on shutdown USB: mxuport: fix null deref when used as a console USB: serial: clean up bus probe error handling USB: serial: fix port attribute-creation race USB: serial: fix tty-device error handling at probe USB: serial: fix potential use-after-free after failed probe USB: console: add dummy __module_get USB: ftdi_sio: add PIDs for Actisense USB devices Revert "USB: serial: make bulk_out_size a lower limit" cdc-acm: Add support for Denso cradle CU-321 usb-storage: support for more than 8 LUNs uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539 USB: usbfs: don't leak kernel data in siginfo xhci: Clear the host side toggle manually when endpoint is 'soft reset' xhci: Allocate correct amount of scratchpad buffers ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds authored
Pull tty/serial fixes from Greg KH: "Here are some tty and serial driver fixes for 4.0-rc3. Along with the atime fix that you know about, here are some other serial driver bugfixes as well. Most notable is a wait_until_sent bugfix that was traced back to being around since before 2.6.12 that Johan has fixed up. All have been in linux-next successfully" * tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: TTY: fix tty_wait_until_sent maximum timeout TTY: fix tty_wait_until_sent on 64-bit machines USB: serial: fix infinite wait_until_sent timeout TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation net: irda: fix wait_until_sent poll timeout serial: uapi: Declare all userspace-visible io types serial: core: Fix iotype userspace breakage serial: sprd: Fix missing spin_unlock in sprd_handle_irq() console: Fix console name size mismatch tty: fix up atime/mtime mess, take four serial: 8250_dw: Fix get_mctrl behaviour serial:8250:8250_pci: delete unneeded quirk entries serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S Change email address for 8250_pci serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO" Revert "tty/serial: of_serial: add DT alias ID handling"
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging driver fixes from Greg KH: "Here are some IIO and staging driver fixes for 4.0-rc3. Details are in the shortlog, nothing major, mostly IIO fixes for reported issues. All have been in linux-next successfully" * tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits) staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel staging: comedi: vmk80xx: remove "firmware version" kernel messages staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample() iio: ak8975: fix AK09911 dependencies iio: common: ssp_sensors: Protect PM-only functions to kill warning IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc Revert "iio:humidity:si7020: fix pointer to i2c client" iio: light: gp2ap020a00f: Select REGMAP_I2C iio: light: jsa1212: Select REGMAP_I2C iio: ad5686: fix optional reference voltage declaration iio:adc:mcp3422 Fix incorrect scales table iio: mxs-lradc: fix iio channel map regression iio: imu: adis16400: Fix sign extension staging: iio: ad2s1200: Fix sign extension iio: mxs-lradc: only update the buffer when its conversions have finished iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions iio: mxs-lradc: make ADC reads not disable touchscreen interrupts iio: mxs-lradc: separate touchscreen and buffer virtual channels iio: imu: inv_mpu6050: Prevent dereferencing NULL iio: iadc: wait_for_completion_timeout time in jiffies ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc driver fixes from Greg KH: "Here are two char/misc fixes for 4.0-rc3. One is a reported binder driver fix needed due to a change in the mm core that happened in 4.0-rc1. Another is a mei driver fix that resolves a reported issue in that driver. Both have been in linux-next for a while" * tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: mei: make device disabled on stop unconditionally android: binder: fix binder mmap failures
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull "code of conflict" from Greg KH: "This file tries to set the rational basis for our code reviews, gives some advice on how to conduct them, and provides an excalation channel for any kernel developers if they so desire it" [ Let's see how this works ] * tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Code of Conflict
-
- 07 Mar, 2015 26 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: "A set of updates and bugfixes for the new designware-baytrail driver. And a documentation bugfix" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: imx: add required clocks property to binding i2c: designware-baytrail: baytrail_i2c_acquire() might sleep i2c: designware-baytrail: cross-check lock functions i2c: designware-baytrail: fix sparse warnings i2c: designware-baytrail: fix typo in error path i2c: designware-baytrail: describe magic numbers
-
git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds authored
Pull slave-dmaengine fixes from Vinod Koul: "This contains small fixes spread across the drivers" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dmaengine: mmp_pdma: fix warning about slave caps dmaengine: qcom_bam_dma: fix wrong register offsets dmaengine: bam-dma: fix a warning about missing capabilities dmaengine: ioatdma: workaround for incorrect DMACAP register dmaengine: at_xdmac: fix for chan conf simplification dmaengine: dw: don't handle interrupt when dmaengine is not used dma: mmp-tdma: refine dma disable and dma-pos update dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Catalin Marinas: "arm64 and generic kernel/module.c (acked by Rusty) fixes for CONFIG_DEBUG_SET_MODULE_RONX" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: kernel/module.c: Update debug alignment after symtable generation arm64: Don't use is_module_addr in setting page attributes
-
Johan Hovold authored
Currently tty_wait_until_sent may take up to twice as long as the requested timeout while waiting for driver and hardware buffers to drain. Fix this by taking the remaining number of jiffies after waiting for driver buffers to drain into account so that the timeout actually becomes a maximum timeout as it is documented to be. Note that this specifically implies tighter timings when closing a port as a consequence of actually honouring the port closing-wait setting for drivers relying on tty_wait_until_sent_from_close (e.g. via tty_port_close_start). Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an infinite timeout (0) would be passed to the underlying tty-driver's wait_until_sent-operation as a negative timeout (-1), causing it to return immediately. This manifests itself for example as tcdrain() returning immediately, drivers not honouring the drain flags when setting terminal attributes, or even dropped data on close as a requested infinite closing-wait timeout would be ignored. The first symptom was reported by Asier LLANO who noted that tcdrain() returned prematurely when using the ftdi_sio usb-serial driver. Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the underlying tty driver. Note that the serial-core wait_until_sent-implementation is not affected by this bug due to a lucky chance (comparison to an unsigned maximum timeout), and neither is the cyclades one that had an explicit check for negative timeouts, but all other tty drivers appear to be affected. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> # v2.6.12 Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Make sure to handle an infinite timeout (0). Note that wait_until_sent is currently never called with a 0-timeout argument due to a bug in tty_wait_until_sent. Fixes: dcf01050 ("USB: serial: add generic wait_until_sent implementation") Cc: stable <stable@vger.kernel.org> # v3.10 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Remove incorrect and redundant wait_until_sent operation, which waits for the driver buffer rather than any hardware buffers to drain, something which is already taken care of by the tty layer (and chars_in_buffer). Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
In case an infinite timeout (0) is requested, the irda wait_until_sent implementation would use a zero poll timeout rather than the default 200ms. Note that wait_until_sent is currently never called with a 0-timeout argument due to a bug in tty_wait_until_sent. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> # v2.6.12 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype. UART drivers use the UPIO_* definitions, but the uapi header defines parallel values and userspace uses these parallel values for ioctls; thus the userspace values are definitive. Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*; extend the uapi defines to include all values in use by the serial core. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
commit 3ffb1a81 ("serial: core: Add big-endian iotype") re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can assign the port iotype (which is expected to match the selected i/o accessors), so iotype values must not be changed. Cc: Kevin Cernekee <cernekee@gmail.com> Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Axel Lin authored
Fix return from sprd_handle_irq() with spin_lock held. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Hurley authored
commit 6ae9200f ("enlarge console.name") increased the storage for the console name to 16 bytes, but not the corresponding struct console_cmdline::name storage. Console names longer than 8 bytes cause read beyond end-of-string and failure to match console; I'm not sure if there are other unexpected consequences. Cc: <stable@vger.kernel.org> # 2.6.22+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Slaby authored
This problem was taken care of three times already in * b0de59b5 (TTY: do not update atime/mtime on read/write), * 37b7f3c7 (TTY: fix atime/mtime regression), and * b0b88565 (tty: fix up atime/mtime mess, take three) But it still misses one point. As John Paul correctly points out, we do not care about setting date. If somebody ever changes wall time backwards (by mistake for example), tty timestamps are never updated until the original wall time passes. So check the absolute difference of times and if it large than "8 seconds or so", always update the time. That means we will update immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the check, but it was always that way. Thanks John for serving me this so nicely debugged. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Cc: <stable@vger.kernel.org> # all, as b0b88565 was backported Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Desmond Liu authored
Fixed behaviour of get_mctrl() serial driver function as documented in: https://www.kernel.org/doc/Documentation/serial/driver Added device-tree properties 'dcd-override', 'dsr-override', 'cts-override', and 'ri-override' specific to the Synopsis 8250 DesignWare UART driver. Allows one to force Data Carrier Detect, Clear To Send, and Data Set Ready signals to permanently be reported as active. The Ring indicator can be forced to be reported as inactive. It is possible that if modem control signalling is enabled on a port that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the driver can hang indefinitely waiting for the state to change. The new DT properties allow the driver to ignore the state of these pins on serial ports that don't support them, as recommended in the kernel documentation. Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com> Signed-off-by: Jonathan Richardson <jonathar@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wang YanQing authored
These quirk entries have the same effect as default quirk entry, so we can just delete them. Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wang YanQing authored
Commit 8b5c913f ("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection") trigger one redundant entry report message. This patch fix it. Reported-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
I'm still receiving reports to my email address, so let's point this at the linux-serial mailing list instead. Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sebastian Andrzej Siewior authored
This reverts commit 0aa525d1. The conditional RX-FIFO read seems to cause spurious interrupts and we see just: |serial8250: too much work for irq29 The previous behaviour was "default" for decades and Marvell's 88f6282 SoC might not be the only that relies on it. Therefore the Omap fix is reverted for now. Fixes: 0aa525d1 ("tty: serial: 8250_core: read only RX if there is something in the FIFO") Reported-By: Nicolas Schichan <nschichan@freebox.fr> Debuged-By: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Baruch Siach authored
This reverts commit 6d01bb9d. The exact same code was added in commit 3239fd31 (serial: of-serial: fetch line number from DT) a few lined above. Doing this once should be enough. Cc: Rob Herring <robh@kernel.org> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull drm fixes from Dave Airlie: "Radeon, imx, msm, and i915 fixes. The msm, imx and i915 ones are fairly run of the mill. Radeon had some DP audio and posting reads for irq fixes, along with a fix for 32-bit kernels with new cards, we were using unsigned long to represent GPU side memory space, but since that changed size on 32 vs 64 cards with lots of VRAM failed, so the change has no effect on x86-64, just moves to using uint64_t instead" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits) drm/msm: kexec fixes drm/msm/mdp5: fix cursor blending drm/msm/mdp5: fix cursor ROI drm/msm/atomic: Don't leak atomic commit object when commit fails drm/msm/mdp5: Avoid flushing registers when CRTC is disabled drm/msm: update generated headers (add 6th lm.base entry) drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes" drm/ttm: device address space != CPU address space drm/mm: Support 4 GiB and larger ranges drm/i915: gen4: work around hang during hibernation drm/i915: Check for driver readyness before handling an underrun interrupt drm/radeon: fix interlaced modes on DCE8 drm/radeon: fix DRM_IOCTL_RADEON_CS oops drm/radeon: do a posting read in cik_set_irq drm/radeon: do a posting read in si_set_irq drm/radeon: do a posting read in evergreen_set_irq drm/radeon: do a posting read in r600_set_irq drm/radeon: do a posting read in rs600_set_irq drm/radeon: do a posting read in r100_set_irq radeon/audio: fix DP audio on DCE6 ...
-
Matt Porter authored
A clock specifier is required for i.MX I2C and is provided in all DTS implementations. Add this to the list of required properties in the binding. Signed-off-by: Matt Porter <mporter@konsulko.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
Andy Shevchenko authored
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages while-loop to do-while and, though it is matter of taste, gives a chance to check one more time before report a timeout. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
Andy Shevchenko authored
It seems the idea behind the cross-check is to prevent acquire semaphore when there is no release callback and vice versa. Thus, patch fixes a typo. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
Andy Shevchenko authored
There is no need to export functions that are used as the callbacks in the struct dw_i2c_dev. Otherwise we get the following warnings: drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static? drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static? While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from functions exported to the modules and redundant assignment of local sem variable. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
Andy Shevchenko authored
It seems we have same message for different return values in get_sem() and baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
Andy Shevchenko authored
The patch converts hardcoded numerical constants to a named ones. While here, align the variable name in get_sem() and reset_semaphore(). Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-
- 06 Mar, 2015 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfsLinus Torvalds authored
Pull btrfs fixes from Chris Mason: "Outside of misc fixes, Filipe has a few fsync corners and we're pulling in one more of Josef's fixes from production use here" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref. Btrfs: fix data loss in the fast fsync path Btrfs: remove extra run_delayed_refs in update_cowonly_root Btrfs: incremental send, don't rename a directory too soon btrfs: fix lost return value due to variable shadowing Btrfs: do not ignore errors from btrfs_lookup_xattr in do_setxattr Btrfs: fix off-by-one logic error in btrfs_realloc_node Btrfs: add missing inode update when punching hole Btrfs: abort the transaction if we fail to update the free space cache inode Btrfs: fix fsync race leading to ordered extent memory leaks
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatchingLinus Torvalds authored
Pull livepatching fix from Jiri Kosina: "Fix an RCU unlock misplacement in live patching infrastructure, from Peter Zijlstra" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching: livepatch: fix RCU usage in klp_find_external_symbol()
-
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermalLinus Torvalds authored
Pull thermal management fixes from Eduardo Valentin: "Specifics: - adding Lukasz as maintainer of samsung thermal driver. - driver fixes: exynos and int430x. - one fix in the exynos cpufreq driver related to cpu cooling (acked by cpufreq maintainer). - fix default sysfs attributes of cooling devices Note: I am sending this pull on Rui's behalf while he fixes issues in his Linux box" * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: thermal: Make sysfs attributes of cooling devices default attributes Thermal/int340x: Fix memleak for aux trip MAINTAINERS: Add entry for SAMSUNG THERMAL DRIVER cpufreq: exynos: Use simple approach to asses if cpu cooling can be used thermal: exynos: Fix wrong control of power down detection mode for Exynos7
-
git://anongit.freedesktop.org/drm-intelDave Airlie authored
two fixes, both cc'd stable. * tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel: drm/i915: gen4: work around hang during hibernation drm/i915: Check for driver readyness before handling an underrun interrupt
-