When perf is used in non-system mode, i.e. without specifying CPUs to
count on, check_and_calc_range falls into the case when it sets
M_TC_EN_ALL in the counter config_base. This has the impact of always
counting for all of the threads in a core, even when the user has not
requested it. For example this can be seen with a test program which
executes 30002 instructions and 10000 branches running on one VPE and a
busy load on the other VPE in the core. Without this commit, the
expected count is not returned:

taskset 4 dd if=/dev/zero of=/dev/null count=100000 & taskset 8 perf
stat -e instructions:u,branches:u ./test_prog

 Performance counter stats for './test_prog':

            103235      instructions:u
             17015      branches:u

In order to fix this, remove check_and_calc_range entirely and perform
all of the logic in mipsxx_pmu_enable_event. Since
mipsxx_pmu_enable_event now requires the range of the event, ensure that
it is set by mipspmu_perf_event_encode in the same circumstances as
before (i.e. #ifdef CONFIG_MIPS_MT_SMP && num_possible_cpus() > 1).

The logic of mipsxx_pmu_enable_event now becomes:
If the CPU is a BMIPS5000, then use the special vpe_id() implementation
to select which VPE to count.
If the counter has a range greater than a single VPE, i.e. it is a
core-wide counter, then ensure that the counter is set up to count
events from all TCs (though, since this is true by definition, is this
necessary? Just enabling a core-wide counter in the per-VPE case appears
experimentally to return the same counts. This is left in for now as the
logic was present before).
If the event is set up to count a particular CPU (i.e. system mode),
then the VPE ID of that CPU is used for the counter.
Otherwise, the event should be counted on the CPU scheduling this thread
(this was the critical bit missing from the previous implementation) so
the VPE ID of this CPU is used for the counter.

With this commit, the same test as before returns the counts expected:

taskset 4 dd if=/dev/zero of=/dev/null count=100000 & taskset 8 perf
stat -e instructions:u,branches:u ./test_prog

 Performance counter stats for './test_prog':

             30002      instructions:u
             10000      branches:u
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19138/Signed-off-by: James Hogan <jhogan@kernel.org>

There are a couple of FIXME's in the perf code which state that
cpu_data[event->cpu].vpe_id reports 0 for both CPUs. This is no longer
the case, since the vpe_id is used extensively by SMP CPS.

VPE local counting gets around this by using smp_processor_id() instead.
As it happens this does work correctly to count events on the right VPE,
but relies on 2 assumptions:
a) Always having 2 VPEs / core.
b) The hardware only paying attention to the least significant bit of
the PERFCTL.VPEID field.
If either of these assumptions change then the incorrect VPEs events
will be counted.

Fix this by replacing smp_processor_id() with
cpu_vpe_id(&current_cpu_data), in the vpe_id() macro, and pass vpe_id()
to M_PERFCTL_VPEID() when setting up PERFCTL.VPEID. The FIXME's can also
be removed since they no longer apply.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19137/Signed-off-by: James Hogan <jhogan@kernel.org>

The presence of per TC performance counters is now detected by
cpu-probe.c and indicated by MIPS_CPU_MT_PER_TC_PERF_COUNTERS in
cpu_data. Switch detection of the feature to use this new flag rather
than blindly testing the implementation specific config7 register with a
magic number.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/19142/Signed-off-by: James Hogan <jhogan@kernel.org>

Processors implementing the MIPS MT ASE may have performance counters
implemented per core or per TC. Processors implemented by MIPS
Technologies signify presence per TC through a bit in the implementation
specific Config7 register. Currently the code which probes for their
presence blindly reads a magic number corresponding to this bit, despite
it potentially having a different meaning in the CPU implementation.

Since CPU features are generally detected by cpu-probe.c, perform the
detection here instead. Introduce cpu_set_mt_per_tc_perf which checks
the bit in config7 and call it from MIPS CPUs known to implement this
bit and the MT ASE, specifically, the 34K, 1004K and interAptiv.

Once the presence of the per-tc counter is indicated in cpu_data, tests
for it can be updated to use this flag.
Suggested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/19136/Signed-off-by: James Hogan <jhogan@kernel.org>

Add phy to switch port connections for PCB123 for internal PHYs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Ocelot has an integrated switch, add support for it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

This work is now performed by the watchdog driver directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

The watchdog is an useful piece of hardware, so there's no reason not to
enable it.

Besides, this is important for restart to work after the change in the
next commit.

This commit enables the Kconfig option in the qi_lb60 defconfig.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

- The previous node requested a memory area of 0x100 bytes, while the
  driver only manipulates four registers present in the first 0x10 bytes.

- The driver requests for the "rtc" clock, but the previous node did not
  provide any.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Also remove the watchdog platform_device from platform.c, since it
wasn't used anywhere anyway.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
[jhogan@kernel.org: Drop jz4740_wdt_device declaration from header]
Signed-off-by: James Hogan <jhogan@kernel.org>

When the watchdog was configured for nowayout, and after the
userspace watchdog daemon closed the dev node without sending the
magic character, unloading this module stopped the watchdog
hardware, which was clearly a problem.

Besides, unloading the module is not possible when the userspace
watchdog daemon is running, so it's safe to assume that we don't
need to stop the watchdog hardware in the jz4740_wdt_remove()
function.

For this reason, the jz4740_wdt_remove() function can then be
dropped alltogether.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

The watchdog driver can restart the system by simply configuring the
hardware for a timeout of 0 seconds.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

- Use devm_clk_get instead of clk_get
- Use devm_watchdog_register_device instead of watchdog_register_device
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Previously, the clock was disabled first, which makes the watchdog
component insensitive to register writes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Trivial fix to spelling mistake in pr_warn message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Re-use kstrtobool_from_user() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Since struct timespec is not y2038 safe on 32bit machines, this patch
converts update_persistent_clock() to update_persistent_clock64() using
struct timespec64.

The rtc_mips_set_time() and rtc_mips_set_mmss() interfaces were using
'unsigned long' type that is not y2038 safe on 32bit machines, moreover
there is only one platform implementing rtc_mips_set_time() and two
platforms implementing rtc_mips_set_mmss(), so we can just make them each
implement update_persistent_clock64() directly, to get that helper out
of the common mips code by removing rtc_mips_set_time() and
rtc_mips_set_mmss() interfaces.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

Since struct timespec is not y2038 safe on 32bit machines, this patch
converts read_persistent_clock() to read_persistent_clock64() using
struct timespec64, as well as converting mktime() to mktime64().
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>

The dummy read_persistent_clock() uses a timespec, which is not year
2038 safe on 32bit systems. Thus remove this obsolete interface.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19114/Signed-off-by: James Hogan <jhogan@kernel.org>

This struct variable is used during init only. It gets passed to the
gpio_led_register_device() which creates its own data copy. That allows
using __initdata and saving some minimal amount of memory.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18928/Signed-off-by: James Hogan <jhogan@kernel.org>

The commit b35cd988 ("lib: Add shared copies of some GCC library
routines") makes it possible to share generic GCC library routines by
several architectures.

This commit removes several generic GCC library routines from
arch/mips/lib/ in favour of similar routines from lib/.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
[Matt Redfearn] Use GENERIC_LIB_* named Kconfig entries
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19051/Signed-off-by: James Hogan <jhogan@kernel.org>

In preparation for removing some of the MIPS compiler intrinsics from
arch/mips/lib, first update the build of vmlinuz to use the generic
ashldi3 from lib.

Both ashldi3 and bswapsi objects need to be built with different CFLAGS
for inclusion to vmlinuz rather than simply including the object built
for the main kernel image. The objects cannot be built directly from
source, since CONFIG_MODVERSIONS changes cmd_cc_o_c to prevent this.

Split the rule to ship ashldi3 and bswapsi from the relevant source
locations.

These files make no reference to other files in their directory, so the
additional CFLAGS are apparently unnecessary - remove them as well.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19050/
[jhogan@kernel.org: Add if_changed and FORCE to fix build failure when
 arch/mips/boot/compressed/ashldi3.c is already generated but there is
 no .ashldi3.c.cmd file yet]
Signed-off-by: James Hogan <jhogan@kernel.org>

When these are included into arch Kconfig files, maintaining
alphabetical ordering of the selects means these get split up. To allow
for keeping things tidier and alphabetical, rename the selects to
GENERIC_LIB_*
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-riscv@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19049/Signed-off-by: James Hogan <jhogan@kernel.org>

As part of the MIPS conversion to use the generic GCC library routines,
Matt Redfearn discovered that I'd missed a notrace on __ucmpdi2().  This
patch rectifies the problem.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19048/Signed-off-by: James Hogan <jhogan@kernel.org>

Some old devices with 4 MiB flashes were using 0x1000 block size and
could use smaller (0x6000 bytes) flash partition for storing NVRAM
content. This adds support for reading NVRAM on Netgear WNR1000 V3.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19005/Signed-off-by: James Hogan <jhogan@kernel.org>

This adds support for detecting this model board and registers some LEDs
and buttons.

There are two uncommon things regarding this device:
1) It can use two different "board_id" ID values.
   Unit I have uses "U12H139T00_NETGEAR" value. This magic is also used
   in firmware file header. There are two reports (one from an OpenWrt
   user) of a different "U12H139T50_NETGEAR" magic though.
2) Power LEDs share GPIOs with buttons.
   Amber one seems to share GPIO 2 with WPS button and green one seems
   to share GPIO 3 with reset button. It remains unknown how to support
   them and handle buttons at the same time. For that reason they aren't
   added to the list of supported LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19004/Signed-off-by: James Hogan <jhogan@kernel.org>

arch/mips/boot/dts/Makefile collects objects from sub-directories into
built-in.a only when CONFIG_BUILTIN_DTB is enabled. Reflect it also to
the sub-directory Makefiles. This suppresses unneeded built-in.a
creation in arch/mips/boot/dts/*/ directories.

While I am here, I replaced $(patsubst %.dtb, %.dtb.o, $(dtb-y)) with
$(addsuffix .o, $(dtb-y)) to simplify the code a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19099/Signed-off-by: James Hogan <jhogan@kernel.org>

Pull drm fixes from Dave Airlie:
 "Exynos, i915, vc4, amdgpu fixes.

  i915:
   - an oops fix
   - two race fixes
   - some gvt fixes

  amdgpu:
   - dark screen fix
   - clk/voltage fix
   - vega12 smu fix

  vc4:
   - memory leak fix

  exynos just drops some code"

* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
  drm/amd/powerplay: header file interface to SMU update
  drm/amd/pp: Fix bug voltage can't be OD separately on VI
  drm/amd/display: Don't program bypass on linear regamma LUT
  drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
  drm/i915/audio: Fix audio detection issue on GLK
  drm/i915: Call i915_perf_fini() on init_hw error unwind
  drm/i915/bios: filter out invalid DDC pins from VBT child devices
  drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
  drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
  drm/exynos: exynos_drm_fb -> drm_framebuffer
  drm/exynos: Move dma_addr out of exynos_drm_fb
  drm/exynos: Move GEM BOs to drm_framebuffer
  drm: Fix HDCP downstream dev count read
  drm/vc4: Fix memory leak during BO teardown
  drm/i915/execlists: Clear user-active flag on preemption completion
  drm/i915/gvt: Add drm_format_mod update
  drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
  drm/i915/gvt: Delete redundant error message in fb_decode.c
  drm/i915/gvt: Cancel dma map when resetting ggtt entries
  drm/i915/gvt: Missed to cancel dma map for ggtt entries
  ...

- Fix a dark screen issue in DC
- Fix clk/voltage dependency tracking for wattman
- Update SMU interface for vega12

* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/amd/powerplay: header file interface to SMU update
  drm/amd/pp: Fix bug voltage can't be OD separately on VI
  drm/amd/display: Don't program bypass on linear regamma LUT

Merge tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

Remove Exynos specific framebuffer structure and
relevant functions.
- it removes exynos_drm_fb structure which is a wrapper of
  drm_framebuffer and unnecessary two exynos specific callback
  functions, exynos_drm_destory() and exynos_drm_fb_create_handle()
  because we can reuse existing drm common callback ones instead.

* tag 'exynos-drm-fixes-for-v4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: exynos_drm_fb -> drm_framebuffer
  drm/exynos: Move dma_addr out of exynos_drm_fb
  drm/exynos: Move GEM BOs to drm_framebuffer
  drm/amdkfd: Deallocate SDMA queues correctly
  drm/amdkfd: Fix scratch memory with HWS enabled

Merge tag 'drm-intel-next-fixes-2018-04-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Fix for FDO #105549: Avoid OOPS on bad VBT (Jani)
- Fix rare pre-emption race (Chris)
- Fix RC6 race against PM transitions (Tvrtko)

* tag 'drm-intel-next-fixes-2018-04-19' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/audio: Fix audio detection issue on GLK
  drm/i915: Call i915_perf_fini() on init_hw error unwind
  drm/i915/bios: filter out invalid DDC pins from VBT child devices
  drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
  drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
  drm/i915/execlists: Clear user-active flag on preemption completion
  drm/i915/gvt: Add drm_format_mod update
  drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
  drm/i915/gvt: Delete redundant error message in fb_decode.c
  drm/i915/gvt: Cancel dma map when resetting ggtt entries
  drm/i915/gvt: Missed to cancel dma map for ggtt entries
  drm/i915/gvt: Make MI_USER_INTERRUPT nop in cmd parser
  drm/i915/gvt: Mark expected switch fall-through in handle_g2v_notification
  drm/i915/gvt: throw error on unhandled vfio ioctls

drm-misc-fixes:

stable: vc4: Fix memory leak during BO teardown (Daniel)
dp: Add i2c retry for LSPCON adapters (Imre)
hdcp: Fix device count mask (Ramalingam)

Cc: Daniel J Blueman <daniel@quora.org
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>

* tag 'drm-misc-fixes-2018-04-18-1' of git://anongit.freedesktop.org/drm/drm-misc:
  drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
  drm: Fix HDCP downstream dev count read
  drm/vc4: Fix memory leak during BO teardown

Pull cifs fixes from Steve French:
 "Various SMB3/CIFS fixes.

  There are three more security related fixes in progress that are not
  included in this set but they are still being tested and reviewed, so
  sending this unrelated set of smaller fixes now"

* tag '4.17-rc1-SMB3-CIFS' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: fix typo in cifs_dbg
  cifs: do not allow creating sockets except with SMB1 posix exensions
  cifs: smbd: Dump SMB packet when configured
  cifs: smbd: Check for iov length on sending the last iov
  fs: cifs: Adding new return type vm_fault_t
  cifs: smb2ops: Fix NULL check in smb2_query_symlink

Pull btrfs fixes from David Sterba:
 "This contains a few fixups to the qgroup patches that were merged this
  dev cycle, unaligned access fix, blockgroup removal corner case fix
  and a small debugging output tweak"

* tag 'for-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: print-tree: debugging output enhancement
  btrfs: Fix race condition between delayed refs and blockgroup removal
  btrfs: fix unaligned access in readdir
  btrfs: Fix wrong btrfs_delalloc_release_extents parameter
  btrfs: delayed-inode: Remove wrong qgroup meta reservation calls
  btrfs: qgroup: Use independent and accurate per inode qgroup rsv
  btrfs: qgroup: Commit transaction in advance to reduce early EDQUOT

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes for x86:

   - Prevent X2APIC ID 0xFFFFFFFF from being treated as valid, which
     causes the possible CPU count to be wrong.

   - Prevent 32bit truncation in calc_hpet_ref() which causes the TSC
     calibration to fail

   - Fix the page table setup for temporary text mappings in the resume
     code which causes resume failures

   - Make the page table dump code handle HIGHPTE correctly instead of
     oopsing

   - Support for topologies where NUMA nodes share an LLC to prevent a
     invalid topology warning and further malfunction on such systems.

   - Remove the now unused pci-nommu code

   - Remove stale function declarations"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/power/64: Fix page-table setup for temporary text mapping
  x86/mm: Prevent kernel Oops in PTDUMP code with HIGHPTE=y
  x86,sched: Allow topologies where NUMA nodes share an LLC
  x86/processor: Remove two unused function declarations
  x86/acpi: Prevent X2APIC id 0xffffffff from being accounted
  x86/tsc: Prevent 32bit truncation in calc_hpet_ref()
  x86: Remove pci-nommu.c

Pull timer fixes from Thomas Gleixner:
 "A small set of timer fixes:

   - Evaluate the -ETIME condition correctly in the imx tpm driver

   - Fix the evaluation order of a condition in posix cpu timers

   - Use pr_cont() in the clockevents code to prevent ugly message
     splitting

   - Remove __current_kernel_time() which is now unused to prevent that
     new users show up.

   - Remove a stale forward declaration"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/imx-tpm: Correct -ETIME return condition check
  posix-cpu-timers: Ensure set_process_cpu_timer is always evaluated
  timekeeping: Remove __current_kernel_time()
  timers: Remove stale struct tvec_base forward declaration
  clockevents: Fix kernel messages split across multiple lines

Pull perf fixes from Thomas Gleixner:
 "A larger set of updates for perf.

  Kernel:

   - Handle the SBOX uncore monitoring correctly on Broadwell CPUs which
     do not have SBOX.

   - Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]. The
     percentage of preempting and non-preempting context switches help
     understanding the nature of workloads (CPU or IO bound) that are
     running on a machine. This adds the kernel facility and userspace
     changes needed to show this information in 'perf script' and 'perf
     report -D' (Alexey Budankov)

   - Remove a WARN_ON() in the trace/kprobes code which is pointless
     because the return error code is already telling the caller what's
     wrong.

   - Revert a fugly workaround for clang BPF targets.

   - Fix sample_max_stack maximum check and do not proceed when an error
     has been detect, return them to avoid misidentifying errors (Jiri
     Olsa)

   - Add SPDX idenitifiers and get rid of GPL boilderplate.

  Tools:

   - Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)

   - Support MAP_FIXED_NOREPLACE, noticed when updating the
     tools/include/ copies (Arnaldo Carvalho de Melo)

   - Add '\n' at the end of parse-options error messages (Ravi Bangoria)

   - Add s390 support for detailed/verbose PMU event description (Thomas
     Richter)

   - perf annotate fixes and improvements:

      * Allow showing offsets in more than just jump targets, use the
        new 'O' hotkey in the TUI, config ~/.perfconfig
        annotate.offset_level for it and for --stdio2 (Arnaldo Carvalho
        de Melo)

      * Use the resolved variable names from objdump disassembled lines
        to make them more compact, just like was already done for some
        instructions, like "mov", this eventually will be done more
        generally, but lets now add some more to the existing mechanism
        (Arnaldo Carvalho de Melo)

   - perf record fixes:

      * Change warning for missing topology sysfs entry to debug, as not
        all architectures have those files, s390 being one of those
        (Thomas Richter)

      * Remove old error messages about things that unlikely to be the
        root cause in modern systems (Andi Kleen)

   - perf sched fixes:

      * Fix -g/--call-graph documentation (Takuya Yamamoto)

   - perf stat:

      * Enable 1ms interval for printing event counters values in
        (Alexey Budankov)

   - perf test fixes:

      * Run dwarf unwind on arm32 (Kim Phillips)

      * Remove unused ptrace.h include from LLVM test, sidesteping older
        clang's lack of support for some asm constructs (Arnaldo
        Carvalho de Melo)

      * Fixup BPF test using epoll_pwait syscall function probe, to cope
        with the syscall routines renames performed in this development
        cycle (Arnaldo Carvalho de Melo)

   - perf version fixes:

      * Do not print info about HAVE_LIBAUDIT_SUPPORT in 'perf version
        --build-options' when HAVE_SYSCALL_TABLE_SUPPORT is true, as
        libaudit won't be used in that case, print info about
        syscall_table support instead (Jin Yao)

   - Build system fixes:

      * Use HAVE_..._SUPPORT used consistently (Jin Yao)

      * Restore READ_ONCE() C++ compatibility in tools/include (Mark
        Rutland)

      * Give hints about package names needed to build jvmti (Arnaldo
        Carvalho de Melo)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
  perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs
  perf/x86/intel/uncore: Revert "Remove SBOX support for Broadwell server"
  coresight: Move to SPDX identifier
  perf test BPF: Fixup BPF test using epoll_pwait syscall function probe
  perf tests mmap: Show which tracepoint is failing
  perf tools: Add '\n' at the end of parse-options error messages
  perf record: Remove suggestion to enable APIC
  perf record: Remove misleading error suggestion
  perf hists browser: Clarify top/report browser help
  perf mem: Allow all record/report options
  perf trace: Support MAP_FIXED_NOREPLACE
  perf: Remove superfluous allocation error check
  perf: Fix sample_max_stack maximum check
  perf: Return proper values for user stack errors
  perf list: Add s390 support for detailed/verbose PMU event description
  perf script: Extend misc field decoding with switch out event type
  perf report: Extend raw dump (-D) out with switch out event type
  perf/core: Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE]
  tools/headers: Synchronize kernel ABI headers, v4.17-rc1
  trace_kprobe: Remove warning message "Could not insert probe at..."
  ...

Pull objtool fix from Thomas Gleixner:
 "A single fix for objtool so it uses the host C and LD flags and not
  the target ones"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Support HOSTCFLAGS and HOSTLDFLAGS

Pull /dev/random fixes from Ted Ts'o:
 "Fix some bugs in the /dev/random driver which causes getrandom(2) to
  unblock earlier than designed.

  Thanks to Jann Horn from Google's Project Zero for pointing this out
  to me"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: add new ioctl RNDRESEEDCRNG
  random: crng_reseed() should lock the crng instance that it is modifying
  random: set up the NUMA crng instances after the CRNG is fully initialized
  random: use a different mixing algorithm for add_device_randomness()
  random: fix crng_ready() test