Return the actual error code from comedi_pci_enable instead of
assuming -EIO on failure. Also, shorten the local variable name 'retval'
to 'ret'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor pci6208_pci_setup() into the attach function. This
function simply enables the pci device and gets the PCI iobase
address used by the driver. There's no need for a separate
function to handle this.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The "local configuration register" stuff is not required. The
io base/range are only queried for use in a kernel message
that it just added noise. Similar with the io range for the
actual io base used by the driver.

Remove both printk's and all the unnecessary code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add defines for the register map of the device. These will be
used to clarify the code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All the boards supported by this driver have 16-bit DACs. The
ao_bits variable in the boardinfo is commented out anyway.
Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the "find pci device" functions consistent in the comedi
drivers. Hopefully well be able to move it into the core...

Refactor the "find pci device" function to return a pointer to
the found struct pci_dev instead of an error code. Also, change
some of the tests to reduce the indent level of the code. Pass
the struct comedi_devconfig pointer to the function instead of
the bus/slot numbers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'thisboard' and 'devpriv' macros rely on a local variable having
a specific name and yield pointers derived from that local variable.
Replace the macros with local variables where used. Use the
comedi_board() helper to get the 'thisboard' pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As pointed out by Ian Abbott, the comedi INSN_WRITE instructions
are meant to iterate over, and write, all the data[] passed from
the comedi core. Modify dac08_write_insn() to work as intended.

Since doc08_write_insn() now returns the proper response to the
core, make the dac08_write() helper return void.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reverse the logic of the test against the cached value so that
the function only has one exit point.

Make the logic of the dac write a bit clearer by create a local
variable for the address used in the outw() calls and masking the
value to write and setting the enable bits before doing the outw()
calls. Add a comment just to make sure it's clear.

Also, add a comment about the 'return 1;'.  This should be
insn->n which is the number of data parameters used to do the
dac08_write_insn() but the insn is not a parameter to this
function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Create local variables for the channel, range, and aref in order
to make the remaining code a bit cleaner.

Remove the extra space in all the comments.

Remove the 'static const int timeout' and just use the open
coded value in the loop.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Create local variables for the channel and range in order to
cleanup to mask/set of the ao_control_bits.

Remove the extra space in all the comments.

Return the number of data parameters used (insn->n) to indicate
success instead of the open coded '1'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Create local variables for the channel and range in order to
cleanup to mask/set of the ao_control_bits.

Remove the extra space in all the comments.

Return the number of data parameters used (insn->n) to indicate
success instead of the open coded '1'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the remaining three "WARNING: line over 80 characters" issues
reported by checkpatch.pl.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add whitespace to all the #define's in the driver in order to
improve the readability. Fix all the comments that are, or
already were, > 80 characters.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'bits' for the DAC_CSR register are currently defined as
enums. All the other registers use defines for the bit definitions.
Change the dac bit enums to defines to follow the other registers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A number of the comments in the private data struct definition
are causing checkpatch.pl to complain about "WARNING: line over
80 characters". Fix the comments.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As indicated by checkpatch.pl, "WARNING: Use of volatile is usually
wrong: ...". The variables in the private data that are marked
volatile don't need to be. Remove the volatile.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove some cut-and-paste comments from the skel driver in the
*_cmdtest functions. Shorten some others to fix the checkpatch.pl
complaints about WARNING: line over 80 characters.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix some of the comments that cause checkpatch.pl to complain
about WARNING: line over 80 characters.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As reported by checkpatch.pl, spaces should not be used before
tabs.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's possible for subdev_8255_init() to fail due to its kzalloc().
Make sure to check for this failure and pass on the error code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the dev->driver->driver_name for the resource name passed
to pci_request_regions(), by way of comedi_pci_enable(), and
to request_irq() instead of the open coded "cb_pcidas".
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the dev_printk messages associated with the "find pci device"
from the *attach function into the *find_pci_device function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Absorb the helper function ai_config_calibration_source() into
ai_config_insn() and remove the static const variable that
was in the helper function.

Return an error code (-EINVAL) when appropriate and the number
of data values used (insn->n) for success.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, rename the ai_se_chans variable to
ai_nchan. It's a bit shorter and provides the necessary
information about the variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the ai_diff_chans variable. This option is not used in
the driver. If it is used later, the value can be easily found
by using ai_se_chans/2.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove all the boardinfo values that are = 0. They will
default to that value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, add whitespace to the boardinfo to
improve readability.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The boardinfo values 'has_ai_trig_gated' and 'has_ai_trig_invert'
are both only set for the "1602" versions of the boards supported
by this driver.

Simplify the boardinfo, and the code, by replacing these two
variables with one "is_1602" variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The defines for the size of the io regions are not used in the
driver. Also, this information can be found using the pci helper
pci_resource_len(). Remove the defines.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This define enables some debug code that output a number
of dev_dbg() messages. These might be useful for development
but should not be in the final driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The defines for the "indices of the base address regions" don't
add much to the readability of the code. They are only used in
the pci_resource_start() calls to get the base address for
the various io regions and the names of the variables provide
adequate documentation.

Remove the defines and just use the open-coded values for the
BARs. Also, remove the incomplete comment above the initialization
of the variables.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These comments are unnecessary.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor the "find pci device" code out of the attach function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'thisboard' and 'devpriv' macros rely on a local variable having
a specific name and yield pointers derived from that local variable.
Replace the macros with local variables where used. use the
comedi_board() helper to get the 'thisboard' pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the nvram_read function, and its helper, to remove the need
for the last of the forward declarations.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the trimpot_{7376,8402}_write functions to remove the need
for the forward declarations.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the caldac_8800_write function, and it's helper, to remove
the need for the forward declaration.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the cb_pcidas_load_counters function to remove the need for
the forward declaration.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the cb_pcida_ao_cancel function to remove the need for
the forward declaration.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>