Change to use SPI_CS_HIGH to support spi CS polarity setting
for chips support enhance_timing.
Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1574053037-26721-2-git-send-email-luhua.xu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20191113094256.1108-8-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113094256.1108-6-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
	dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit d948e6ca ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.

This causes SPI devices to return errors for cases where they do:

ret = spi_setup(spi);
if (ret)
	return ret;

As in many cases the SPI devices do not check for if (ret < 0).

Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.

Fixes: d948e6ca ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.comSigned-off-by: Mark Brown <broonie@kernel.org>

pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.

Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.

In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).

Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.

As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.

Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to

Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nzSigned-off-by: Mark Brown <broonie@kernel.org>

Set use_gpio_descriptors to true and avoid asserting the native chip
select if the spi core has done it for us.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-2-chris.packham@alliedtelesis.co.nzSigned-off-by: Mark Brown <broonie@kernel.org>

The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.comSigned-off-by: Mark Brown <broonie@kernel.org>

As to set_cs takes effect immediately, power spi
is needed when setup spi.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1572426234-30019-1-git-send-email-luhua.xu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

This driver does not use any symbols from the legacy GPIO
header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073624.23974-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The DW driver does not use the legacy GPIO header so drop
it from the spi-dw.h include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073418.23717-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.

As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.

We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.

Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Committed version of the commit b9fc2d20 ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.

Complete the code move by doing those changes now.

Fixes: b9fc2d20 ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.

Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

When rebooting the system, we should lock the watchdog after
configuration to make sure the watchdog can reboot the system
successfully.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/7b04711127434555e3a1a86bc6be99860cd86668.1572257085.git.baolin.wang@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.comSigned-off-by: Mark Brown <broonie@kernel.org>

This property is used to set the number of bits per transfer (bits_per_word).

Xilinx' IP core allows either 8, 16 or 32, and is non changeable on runtime,
only when instantiating the core.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-2-alvaro.gamez@hazent.comSigned-off-by: Mark Brown <broonie@kernel.org>

Two spelling mistakes are being fixed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191023121643.25237-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This change documents the CS setup, host & inactive times. They were
omitted when the fields were added, and were caught by one of the build
bots.

Fixes: 25093bde ("spi: implement SW control for CS times")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191023070046.12478-1-alexandru.ardelean@analog.comSigned-off-by: Mark Brown <broonie@kernel.org>

Intel(R) Programmable Services Engine (Intel(R) PSE) SPI controllers in
Intel Elkhart Lake have two Chip Select signals instead of one.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-3-jarkko.nikula@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Implement pm_runtime hooks at pci driver.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
[jarkko.nikula@linux.intel.com: Forward ported on top of
commit 1e695983 ("spi: dw: Add basic runtime PM support")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-2-jarkko.nikula@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>