Wakeup domain in J721E SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Main domain in J721E has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
	- Main Navss Interrupt Router connected to main navss inta and mailboxes.
	- Main Navss Interrupt Aggregator connected to main domain UDMASS

Add DT nodes for the interrupt controllers available in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the Interrupt controller node for the Interrupt Router present within
the Main NavSS module. This Interrupt Router can route 192 interrupts to
the GIC_SPI in 3 sets of 64 interrupts each. Note that the last set is
reserved for the host ID A72_3 for hypervisor usecases, so the node is
added only with 2 sets for the Linux kernel context (host id A72_2). This
is specified through the ti,sci-rm-range-girq property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Enable J721E SoC support from TI.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add Support for J721E Common Processor board support.
The EVM architecture is as follows:

+------------------------------------------------------+
|   +-------------------------------------------+      |
|   |                                           |      |
|   |        Add-on Card 1 Options              |      |
|   |                                           |      |
|   +-------------------------------------------+      |
|                                                      |
|                                                      |
|                     +-------------------+            |
|                     |                   |            |
|                     |   SOM             |            |
|  +--------------+   |                   |            |
|  |              |   |                   |            |
|  |  Add-on      |   +-------------------+            |
|  |  Card 2      |                                    |    Power Supply
|  |  Options     |                                    |    |
|  |              |                                    |    |
|  +--------------+                                    | <---
+------------------------------------------------------+
                                Common Processor Board

Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).

Note:
A) The minimum configuration required to boot up the board is System On
   Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
   maintaining common processor board as the base dts and SOM as the dtsi
   that we include. In the future as more SOM's appear, we should move
   common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
   overlays.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add option to build J721E SoC specific components
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.

Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
  capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
  C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
  and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
  PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
  up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
  addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
  capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
  16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
  I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
  management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
  capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
  Management (DMSC)

See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

J721e uses a UART controller that is compatible with AM654 UART.
Introduce a specific compatible to help handle the differences if
necessary.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.

Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
  capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
  C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
  and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
  PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
  up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
  addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
  capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
  16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
  I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
  management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
  capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
  Management (DMSC)

See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

AM654 base board does not have any PCIe slots. Disable all the
SERDES and PCIe instances.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add PCIe Endpoint DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add PCIe Root Complex DT node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add DT node for SERDES0 and SERDES1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add mux-controller DT node as a child node of scm_conf. This is
required for muxing SERDES between USB, PCIe and ICSS2 SGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

GIC_ITS used in AM654 platform has the same configuration as that of
GIC_ITS used in Socionext SoCs. Add "socionext,synquacer-pre-its"
property to get PCI MSI working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the MSCM RAM address space to the ranges property of the cbass_main
interconnect node so that the addresses can be translated properly.

This fixes the probe failure in the sram driver for the MSMC RAM node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the on-chip SRAM present within the MCU domain as a mmio-sram node.
The K3 AM65x SoCs have 512 KB of such memory. Any specific memory range
within this RAM needed by a software module ought to be reserved using
an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the address space for the MCU SRAM memory to the ranges property
of the cbass_mcu interconnect node so that the addresses within the
mcu_sram nodes and its children can be translated properly by the
relevant OF address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

There are 2 push buttons: SW5 and SW6 that are basically connected to
WKUP_GPIO0_24 and WKUP_GPIO0_27 respectively. Add the respective
nodes and the pinctrl data to set the mode to GPIO and Input.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add gpio0/1 nodes under main domain. They have 96 and 90 gpios
respectively and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add gpio0 node under wakeup domain. This has 56 gpios
and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Wakeup domain in AM654 SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Main domain in AM654 has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
    - Main Navss Interrupt Router connected to main navss inta and mailboxes.
    - Main Navss Interrupt Aggregator connected to main domain UDMASS

Add DT nodes for the above three interrupt controllers available
in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Use the am654 specific compatible for dmsc. This allows to use
the am654 specific RM mapping table.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Pull UBIFS fixes from Richard Weinberger:

 - build errors wrt xattrs

 - mismerge which lead to a wrong Kconfig ifdef

 - missing endianness conversion

* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubifs: Convert xattr inum to host order
  ubifs: Use correct config name for encryption
  ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR

Merge yet more updates from Andrew Morton:
 "A few final bits:

   - large changes to vmalloc, yielding large performance benefits

   - tweak the console-flush-on-panic code

   - a few fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  panic: add an option to replay all the printk message in buffer
  initramfs: don't free a non-existent initrd
  fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
  mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
  mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
  mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
  mm/vmalloc.c: keep track of free blocks for vmap allocation

Pull more Kbuild updates from Masahiro Yamada:

 - remove unneeded use of cc-option, cc-disable-warning, cc-ldoption

 - exclude tracked files from .gitignore

 - re-enable -Wint-in-bool-context warning

 - refactor samples/Makefile

 - stop building immediately if syncconfig fails

 - do not sprinkle error messages when $(CC) does not exist

 - move arch/alpha/defconfig to the configs subdirectory

 - remove crappy header search path manipulation

 - add comment lines to .config to clarify the end of menu blocks

 - check uniqueness of module names (adding new warnings intentionally)

* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
  kconfig: use 'else ifneq' for Makefile to improve readability
  kbuild: check uniqueness of module names
  kconfig: Terminate menu blocks with a comment in the generated config
  kbuild: add LICENSES to KBUILD_ALLDIRS
  kbuild: remove 'addtree' and 'flags' magic for header search paths
  treewide: prefix header search paths with $(srctree)/
  media: prefix header search paths with $(srctree)/
  media: remove unneeded header search paths
  alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
  kbuild: terminate Kconfig when $(CC) or $(LD) is missing
  kbuild: turn auto.conf.cmd into a mandatory include file
  .gitignore: exclude .get_maintainer.ignore and .gitattributes
  kbuild: add all Clang-specific flags unconditionally
  kbuild: Don't try to add '-fcatch-undefined-behavior' flag
  kbuild: add some extra warning flags unconditionally
  kbuild: add -Wvla flag unconditionally
  arch: remove dangling asm-generic wrappers
  samples: guard sub-directories with CONFIG options
  kbuild: re-enable int-in-bool-context warning
  MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
  ...

Pull i2c updates from Wolfram Sang:
 "Some I2C core API additions which are kind of simple but enhance error
  checking for users a lot, especially by returning errno now.

  There are wrappers to still support the old API but it will be removed
  once all users are converted"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: add device-managed version of i2c_new_dummy
  i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy

Pull ext4 fixes from Ted Ts'o:
 "Some bug fixes, and an update to the URL's for the final version of
  Unicode 12.1.0"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: avoid panic during forced reboot due to aborted journal
  ext4: fix block validity checks for journal inodes using indirect blocks
  unicode: update to Unicode 12.1.0 final
  unicode: add missing check for an error return from utf8lookup()
  ext4: fix miscellaneous sparse warnings
  ext4: unsigned int compared against zero
  ext4: fix use-after-free in dx_release()
  ext4: fix data corruption caused by overlapping unaligned and aligned IO
  jbd2: fix potential double free
  ext4: zero out the unused memory region in the extent tree block

Pull cifs fixes from Steve French:
 "Minor cleanup and fixes, one for stable, four rdma (smbdirect)
  related. Also adds SEEK_HOLE support"

* tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: add support for SEEK_DATA and SEEK_HOLE
  Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file
  cifs: Allocate memory for all iovs in smb2_ioctl
  cifs: Don't match port on SMBDirect transport
  cifs:smbd Use the correct DMA direction when sending data
  cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called
  cifs: use the right include for signal_pending()
  smb3: trivial cleanup to smb2ops.c
  cifs: cleanup smb2ops.c and normalize strings
  smb3: display session id in debug data

Pull perf tooling updates from Ingo Molnar:
 "perf.data:

   - Streaming compression of perf ring buffer into
     PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x
     perf.data file size reduction on variety of tested workloads what
     saves storage space on larger server systems where perf.data size
     can easily reach several tens or even hundreds of GiBs, especially
     when profiling with DWARF-based stacks and tracing of context
     switches.

  perf record:

   - Improve -user-regs/intr-regs suggestions to overcome errors

  perf annotate:

   - Remove hist__account_cycles() from callback, speeding up branch
     processing (perf record -b)

  perf stat:

   - Add a 'percore' event qualifier, e.g.: -e
     cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for
     both hardware threads in a core.

     We can already do this with --per-core, but it's often useful to do
     this together with other metrics that are collected per hardware
     thread.

     I.e. now its possible to do this per-event, and have it mixed with
     other events not aggregated by core.

  arm64:

   - Map Brahma-B53 CPUID to cortex-a53 events.

   - Add Cortex-A57 and Cortex-A72 events.

  csky:

   - Add DWARF register mappings for libdw, allowing --call-graph=dwarf
     to work on the C-SKY arch.

  x86:

   - Add support for recording and printing XMM registers, available,
     for instance, on Icelake.

   - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON
     support. UPI replaced the Intel QuickPath Interconnect (QPI) in
     Xeon Skylake-SP.

  Intel PT:

   - Fix instructions sampling rate.

   - Timestamp fixes.

   - Improve exported-sql-viewer GUI, allowing, for instance, to
     copy'n'paste the trees, useful for e-mailing"

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits)
  perf stat: Support 'percore' event qualifier
  perf stat: Factor out aggregate counts printing
  perf tools: Add a 'percore' event qualifier
  perf docs: Add description for stderr
  perf intel-pt: Fix sample timestamp wrt non-taken branches
  perf intel-pt: Fix improved sample timestamp
  perf intel-pt: Fix instructions sampling rate
  perf regs x86: Add X86 specific arch__intr_reg_mask()
  perf parse-regs: Add generic support for arch__intr/user_reg_mask()
  perf parse-regs: Split parse_regs
  perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events
  perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events
  perf vendor events arm64: Remove [[:xdigit:]] wildcard
  perf jevents: Remove unused variable
  perf test zstd: Fixup verbose mode output
  perf tests: Implement Zstd comp/decomp integration test
  perf inject: Enable COMPRESSED record decompression
  perf report: Implement perf.data record decompression
  perf record: Implement -z,--compression_level[=<n>] option
  perf report: Add stub processing of compressed events for -D
  ...

Pull clocksource updates from Ingo Molnar:
 "Misc clocksource/clockevent driver updates that came in a bit late but
  are ready for v5.2"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  misc: atmel_tclib: Do not probe already used TCBs
  clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
  clocksource/drivers/tcb_clksrc: Rename the file for consistency
  clocksource/drivers/timer-atmel-pit: Rework Kconfig option
  clocksource/drivers/tcb_clksrc: Move Kconfig option
  ARM: at91: Implement clocksource selection
  clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
  clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
  ARM: at91: move SoC specific definitions to SoC folder
  clocksource/drivers/timer-milbeaut: Cleanup common register accesses
  clocksource/drivers/timer-milbeaut: Add shutdown function
  clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
  clocksource/drivers/tegra: Rework for compensation of suspend time
  clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
  clocksource/drivers/sun4i: Add a compatible for suniv
  dt-bindings: timer: Add Allwinner suniv timer

Pull IRQ chip updates from Ingo Molnar:
 "A late irqchips update:

   - New TI INTR/INTA set of drivers

   - Rewrite of the stm32mp1-exti driver as a platform driver

   - Update the IOMMU MSI mapping API to be RT friendly

   - A number of cleanups and other low impact fixes"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
  iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
  irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
  irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
  irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
  irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
  iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
  genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
  arm64: arch_k3: Enable interrupt controller drivers
  irqchip/ti-sci-inta: Add msi domain support
  soc: ti: Add MSI domain bus support for Interrupt Aggregator
  irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
  dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
  irqchip/ti-sci-intr: Add support for Interrupt Router driver
  dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
  gpio: thunderx: Use the default parent apis for {request,release}_resources
  genirq: Introduce irq_chip_{request,release}_resource_parent() apis
  firmware: ti_sci: Add helper apis to manage resources
  firmware: ti_sci: Add RM mapping table for am654
  firmware: ti_sci: Add support for IRQ management
  firmware: ti_sci: Add support for RM core ops
  ...

Pull EFI fix from Ingo Molnar:
 "Fix an EFI-fb regression that affects certain x86 systems"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  fbdev/efifb: Ignore framebuffer memmap entries that lack any memory types

Pull core fixes from Ingo Molnar:
 "This fixes a particularly thorny munmap() bug with MPX, plus fixes a
  host build environment assumption in objtool"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Allow AR to be overridden with HOSTAR
  x86/mpx, mm/core: Fix recursive munmap() corruption

Pull ARM SoC late updates from Olof Johansson:
 "This is some material that we picked up into our tree late. Most of it
  are smaller fixes and additions, some defconfig updates due to recent
  development, etc.

  Code-wise the largest portion is a series of PM updates for the at91
  platform, and those have been in linux-next a while through the at91
  tree before we picked them up"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
  arm64: dts: sprd: Add clock properties for serial devices
  Opt out of scripts/get_maintainer.pl
  ARM: ixp4xx: Remove duplicated include from common.c
  soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe
  arm64: tegra: Disable XUSB support on Jetson TX2
  arm64: tegra: Enable SMMU translation for PCI on Tegra186
  arm64: tegra: Fix insecure SMMU users for Tegra186
  arm64: tegra: Select ARM_GIC_PM
  amba: tegra-ahb: Mark PM functions as __maybe_unused
  ARM: dts: logicpd-som-lv: Fix MMC1 card detect
  ARM: mvebu: drop return from void function
  ARM: mvebu: prefix coprocessor operand with p
  ARM: mvebu: drop unnecessary label
  ARM: mvebu: fix a leaked reference by adding missing of_node_put
  ARM: socfpga_defconfig: enable LTC2497
  ARM: mvebu: kirkwood: remove error message when retrieving mac address
  ARM: at91: sama5: make ov2640 as a module
  ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled
  ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM
  soc/fsl/qe: Fix an error code in qe_pin_request()
  ...

Pull powerpc fixes from Michael Ellerman:
 "One fix going back to stable, for a bug on 32-bit introduced when we
  added support for THREAD_INFO_IN_TASK.

  A fix for a typo in a recent rework of our hugetlb code that leads to
  crashes on 64-bit when using hugetlbfs with a 4K PAGE_SIZE.

  Two fixes for our recent rework of the address layout on 64-bit hash
  CPUs, both only triggered when userspace tries to access addresses
  outside the user or kernel address ranges.

  Finally a fix for a recently introduced double free in an error path
  in our cacheinfo code.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Sachin Sant, Tobin C.
  Harding"

* tag 'powerpc-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/cacheinfo: Remove double free
  powerpc/mm/hash: Fix get_region_id() for invalid addresses
  powerpc/mm: Drop VM_BUG_ON in get_region_id()
  powerpc/mm: Fix crashes with hugepages & 4K pages
  powerpc/32s: fix flush_hash_pages() on SMP

Pull a few more MIPS updates from Paul Burton:
 "Some SGI IP27 specific PCI rework and a batch of fixes:

   - A build fix for BMIPS5000 configurations with
     CONFIG_HW_PERF_EVENTS=y, which also neatly removes some #ifdefery.

   - A fix to report supported ISAs correctly on older Ingenic SoCs
     which incorrectly indicate MIPSr2 support in their cop0 Config
     register.

   - Some PCI modernization for SGI IP27 systems as part of ongoing work
     to support some other SGI systems.

   - A fix allowing use of appended DTB files with generic kernels.

   - DMA mask fixes for SGI IP22 & Alchemy systems"

* tag 'mips_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: Alchemy: add DMA masks for on-chip ethernet
  MIPS: SGI-IP22: provide missing dma_mask/coherent_dma_mask
  generic: fix appended dtb support
  MIPS: SGI-IP27: abstract chipset irq from bridge
  MIPS: SGI-IP27: use generic PCI driver
  MIPS: Fix Ingenic SoCs sometimes reporting wrong ISA
  MIPS: perf: Fix build with CONFIG_CPU_BMIPS5000 enabled