Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Configures the framer of the HDMI connection.
By default starts in HDMI mode and can be swtich to DVI.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Make the value of the colorspace of the HDMI infoframe configurable.
HDMI colorspace could be: RGB, YUV422 or YUV444
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Vendor specific infoframe is mandatory for 4K2K resolution.
Without this, the HDMI protocol compliance fails.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Clear all infoframe registers when the HDMI link is stopped.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Set the infoframe transmission mode according to the type of
the infoframe.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Make sure the HD DACS are disabled when the HDA connector
is created.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Modify AWG algorithm in order to handle more than 1023 lines
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

Modify delay to display last pixel column on DVO
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

The DVO connector is tag as disconnect because of a wrong management
of the panel detection.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Disable the clipping mode for hdmi, dvo and hda connectors.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

Use BT601 for SD/ED resolution and BT709 for HD resolution
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

Atomic update should never fail. Thus all checks must be done in
the atomic_check function for each plane (gdp, hqvdp and cursor).
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

It may happen that the cursor is displayed with wrong colors which can
be explained by a CLUT wrongly fetched at the first display.
Fetching the CLUT at each commit (=move) ensures that the right colors
are used, at least from the first cursor move.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

GDP source width should be equal to the destination width to get
rid of this issue.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

When a GDP gets a scale request (which it does not support), it accepts it
but crops or clamps and outputs a warning message.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

Only RGB formats supported by GDP planes
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

When a frame or a field is skipped, output a Warning message instead of
an Error message.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

data_en is a local variable that doesn't need to be set as
awg_generate_instr can be called directly with the requested value.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

This update eases to understand the VTG programming.
It also sets a VTG output id for each supported connectors.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>

sti now support of atomic modesetting so set the flag to enable it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

fix x/y typo while setting cursor coordinates
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

Set CRTC modesetting parameters to avoid warnings in atomic mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

In some cases last_close() could be called before sti_gdp_disable()
and make kernel crash because mixer structure has been destroy.
Let's gdp keep a reference on vtg to fix that (like it is already done
in HQVDP)
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>

As previously discussed, this is my first pull request for the DCU DRM
driver along with the change in MAINTAINERS.
https://lkml.org/lkml/2016/1/7/26

The pull contains some code cleanup changes (e.g. removing all error
handling for the regmap calls) and several fixes.

* 'for-next' of http://git.agner.ch/git/linux-drm-fsl-dcu:
  drm/fsl-dcu: fix register initialization
  drm/fsl-dcu: use mode flags for hsync/vsync polarity
  drm/fsl-dcu: fix alpha blending
  drm/fsl-dcu: mask all interrupts on initialization
  drm/fsl-dcu: handle initialization errors properly
  drm/fsl-dcu: avoid memory leak on errors
  drm/fsl-dcu: remove regmap return value checks
  drm/fsl-dcu: specify volatile registers
  drm: fsl-dcu: Fix no fb check bug
  MAINTAINERS: update for Freescale DCU DRM driver

The layer enumeration start with 0 (0-15 for LS1021a and 0-63 for
Vybrid) whereas the register enumeration start from 1 (1-10 for
LS1021a and 1-9 for Vybrid). The loop started off from 0 for both
iterations and initialized the number of layers inclusive, which
is one layer too many.

All extensively written registers seem to be unassigned, it seems
that the write to those registers did not do any harm in practice.
Signed-off-by: Stefan Agner <stefan@agner.ch>

The current default configuration is as follows:
- Invert VSYNC signal (active LOW)
- Invert HSYNC signal (active LOW)

The mode flags allow to specify the required polarity per
mode. Furthermore, none of the current driver settings is
actually a standard polarity.

This patch applies the current driver default polarities as
explicit flags to the display which has been introduced with
the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now
also parses the flags field and applies the configuration
accordingly, by using the following values as standard
polarities: (e.g. when no flags are specified):
- VSYNC signal not inverted (active HIGH)
- HSYNC signal not inverted (active HIGH)
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>

Fix alpha blending by enabling alpha blending for the whole frame if
a color mode with alpha channel is selected (DRM_FORMAT_ARGB*). Also
support color modes without alpha channel (DRM_FORMAT_XRGB*) by just
not enabling alpha blending on layer level.
Signed-off-by: Stefan Agner <stefan@agner.ch>

The state of the interrupt mask register on initialization is
unknown, e.g. U-Boot could already used the DCU. So depending on
the boot loader, the outcome of the interrupt mask register could
be different. A defined state is much more preferable. Also, there
is no value in keeping interrupts enabled which we don't need.
Therefor, mask all interrupts on initialization.
Signed-off-by: Stefan Agner <stefan@agner.ch>

If initialization fails (e.g. due to missing panel node or deferred
probe) make sure to roll-back all operations and return the error
code.
Signed-off-by: Stefan Agner <stefan@agner.ch>

Improve error handling during CRTC initialization. Especially avoid
memory leaks in the primary plane initialization error path.
Signed-off-by: Stefan Agner <stefan@agner.ch>