Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).

In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.

The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.

Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.

Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.

Before commit 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.

Fixes: 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update email addresses of liquidio driver maintainers.  Also remove a
former maintainer.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Acked-by: Derek Chickles <dchickles@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"also enables" should not be spelled as one word.

Fixes: cfc80d9a ("net: Introduce net_failover driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.

This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:

[    1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074
[    1.498110] pgd = (ptrval)
[    1.500838] [00000074] *pgd=00000000
[    1.504432] Internal error: Oops: 17 [#1] SMP ARM
[    1.509133] Modules linked in:
[    1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99
[    1.520708] Hardware name: Xilinx Zynq Platform
[    1.525261] Workqueue: events deferred_probe_work_func
[    1.530403] PC is at klist_next+0x10/0xfc
[    1.534403] LR is at device_for_each_child+0x40/0x94
[    1.539361] pc : [<c0683fbc>]    lr : [<c0455d90>]    psr: 200e0013
[    1.545628] sp : ceeefe68  ip : 00000001  fp : ffffe000
[    1.550863] r10: 00000000  r9 : c0c66790  r8 : 00000000
[    1.556079] r7 : c0457d44  r6 : 00000000  r5 : ceeefe8c  r4 : cfa2ec78
[    1.562604] r3 : 00000064  r2 : c0457d44  r1 : ceeefe8c  r0 : 00000064
[    1.569129] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    1.576263] Control: 18c5387d  Table: 0ed7804a  DAC: 00000051
[    1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval))
[    1.588280] Stack: (0xceeefe68 to 0xceef0000)
[    1.592630] fe60:                   cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790
[    1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78
[    1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac
[    1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10
[    1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c
[    1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c
[    1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00
[    1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000
[    1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4
[    1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000
[    1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[    1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[    1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94)
[    1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94)
[    1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40)
[    1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c)
[    1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc)
[    1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0)
[    1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154)
[    1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    1.785689] Exception stack(0xceeeffb0 to 0xceeefff8)
[    1.790739] ffa0:                                     00000000 00000000 00000000 00000000
[    1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010)
[    1.819844] ---[ end trace 3c2c0c8b65399ec9 ]---

The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.

To fix this, we simply add the missing device_del() invocation in the
error path.

Fixes: 69226896 ("mdio_bus: Issue GPIO RESET to PHYs")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix "reference to nonexisting document" warnings.

Fixes: b255e500 ("net: documentation: build a directory structure for drivers")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.

Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.

Fixes: 732f2ab7 ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).

To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1

So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.

Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.

To solve this issue, when logging with device IOTLB enabled, we will:

1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
   get HVA, for writable descriptor, get HVA through iovec. For used
   ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
   through GPA. Pay attention this reverse mapping is not guaranteed
   to be unique, so we should log each possible GPA in this case.

This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Cc: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_tstamp.h is an UAPI header, so it was moved under include/uapi.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cb9f1b78, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:

Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
    TX: bytes  packets  errors  dropped carrier collsns
    0          0        1       0       0       0

The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).

This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 23b0269e ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.

And this issue was found with LTP/network tests as well.

Fixes: 23b0269e ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 4cdeeee9 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.

The issue was found with LTP/network tests (UDP-Lite test-cases).

Fixes: 4cdeeee9 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes (especially 05cd271f ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.

v2:
- use kzalloc() instead of kcalloc()

Fixes: 05cd271f ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.

Also fix up the related struct device_node leaks.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org>     # 4.19: 36156f92
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shifting the 1 by exp by an int can lead to sign-extension overlow when
exp is 31 since 1 is an signed int and sign-extending this result to an
unsigned long long will set the upper 32 bits.  Fix this by shifting an
unsigned long.

Detected by cppcheck:
(warning) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.

Fixes: bec1f6f6 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not
an explicit section. so linking warning occurred at compile time for the
powerpc.
So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh".

Config condition:

CONFIG_BPFILTER=y
CONFIG_BPFILTER_UMH=y

Result:

ld: warning: orphan section `.bpfilter_umh' from
`net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh'

Fixes: 61fbf593 ("net: bpfilter: restart bpfilter_umh when error occurred")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

"IPv6: " prefix is already added by pr_fmt, no need to include
it again in the pr_warn() format.  The message predates extack
support, we can replace the whole thing with an extack message.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In iproute2 commit 90c5c969f0b9 ("fix print_0xhex on 32 bit"), the format
specifier for the ife type changed from 0x%X to %#llX, causing systematic
failures in the following TDC test cases:

 7682 - Create valid ife encode action with mark and pass control
 ef47 - Create valid ife encode action with mark and pipe control
 df43 - Create valid ife encode action with mark and continue control
 e4cf - Create valid ife encode action with mark and drop control
 ccba - Create valid ife encode action with mark and reclassify control
 a1cf - Create valid ife encode action with mark and jump control
 cb3d - Create valid ife encode action with mark value at 32-bit maximum
 95ed - Create valid ife encode action with prio and pass control
 aa17 - Create valid ife encode action with prio and pipe control
 74c7 - Create valid ife encode action with prio and continue control
 7a97 - Create valid ife encode action with prio and drop control
 f66b - Create valid ife encode action with prio and reclassify control
 3056 - Create valid ife encode action with prio and jump control
 7dd3 - Create valid ife encode action with prio value at 32-bit maximum
 05bb - Create valid ife encode action with tcindex and pass control
 ce65 - Create valid ife encode action with tcindex and pipe control
 09cd - Create valid ife encode action with tcindex and continue control
 8eb5 - Create valid ife encode action with tcindex and continue control
 451a - Create valid ife encode action with tcindex and drop control
 d76c - Create valid ife encode action with tcindex and reclassify control
 e731 - Create valid ife encode action with tcindex and jump control
 b7b8 - Create valid ife encode action with tcindex value at 16-bit maximum
 2a9c - Create valid ife encode action with mac src parameter
 cf5c - Create valid ife encode action with mac dst parameter
 2353 - Create valid ife encode action with mac src and mac dst parameters
 552c - Create valid ife encode action with mark and type parameters
 0421 - Create valid ife encode action with prio and type parameters
 4017 - Create valid ife encode action with tcindex and type parameters
 fac3 - Create valid ife encode action with index at 32-bit maximnum
 7c25 - Create valid ife decode action with pass control
 dccb - Create valid ife decode action with pipe control
 7bb9 - Create valid ife decode action with continue control
 d9ad - Create valid ife decode action with drop control
 219f - Create valid ife decode action with reclassify control
 8f44 - Create valid ife decode action with jump control
 b330 - Create ife encode action with cookie

Change 'matchPattern' values, allowing '0' and '0x0' if ife type is equal
to 0, and accepting both '0x' and '0X' otherwise, to let these tests pass
both with old and new tc binaries.
While at it, fix a small typo in test case fac3 ('maximnum'->'maximum').
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This should be 1 for normal allocations, 0 disables leak reporting.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Fixes: 85704cb8 ("net/core/neighbour: tell kmemleak about hash tables")
Signed-off-by: David S. Miller <davem@davemloft.net>

The similar issue as fixed in Commit 4a2eb0c3 ("sctp: initialize
sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists
in sctp_inetaddr_event, as Alexander noticed.

To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp
ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist().
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As said in draft-foschiano-erspan-03#section4:

   Different frame variants known as "ERSPAN Types" can be
   distinguished based on the GRE "Protocol Type" field value: Type I
   and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].

So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().

Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number.  This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

New device of TRENDnet based on aqc111u
Add this ID to blacklist of cdc_ether driver as well
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.

This bug is _not_ introduced by commit 3b3ae880
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b968 ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.

Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add document for below counters:
TcpEstabResets
TcpAttemptFails
TcpOutRsts
TcpExtTCPSACKDiscard
TcpExtTCPDSACKIgnoredOld
TcpExtTCPDSACKIgnoredNoUndo
TcpExtTCPSackShifted
TcpExtTCPSackMerged
TcpExtTCPSackShiftFallback
TcpExtTCPWantZeroWindowAdv
TcpExtTCPToZeroWindowAdv
TcpExtTCPFromZeroWindowAdv
TcpExtDelayedACKs
TcpExtDelayedACKLocked
TcpExtDelayedACKLost
TcpExtTCPLossProbes
TcpExtTCPLossProbeRecovery
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both gue_err() and gue6_err() incorrectly assume
linear skbs. Fix them to use pskb_may_pull().

BUG: KMSAN: uninit-value in gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
CPU: 0 PID: 18083 Comm: syz-executor1 Not tainted 5.0.0-rc1+ #7
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x173/0x1d0 lib/dump_stack.c:113
 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600
 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
 gue6_err+0x475/0xc40 net/ipv6/fou6.c:101
 __udp6_lib_err_encap_no_sk net/ipv6/udp.c:434 [inline]
 __udp6_lib_err_encap net/ipv6/udp.c:491 [inline]
 __udp6_lib_err+0x18d0/0x2590 net/ipv6/udp.c:522
 udplitev6_err+0x118/0x130 net/ipv6/udplite.c:27
 icmpv6_notify+0x462/0x9f0 net/ipv6/icmp.c:784
 icmpv6_rcv+0x18ac/0x3fa0 net/ipv6/icmp.c:872
 ip6_protocol_deliver_rcu+0xb5a/0x23a0 net/ipv6/ip6_input.c:394
 ip6_input_finish net/ipv6/ip6_input.c:434 [inline]
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ip6_input+0x2b6/0x350 net/ipv6/ip6_input.c:443
 dst_input include/net/dst.h:450 [inline]
 ip6_rcv_finish+0x4e7/0x6d0 net/ipv6/ip6_input.c:76
 NF_HOOK include/linux/netfilter.h:289 [inline]
 ipv6_rcv+0x34b/0x3f0 net/ipv6/ip6_input.c:272
 __netif_receive_skb_one_core net/core/dev.c:4973 [inline]
 __netif_receive_skb net/core/dev.c:5083 [inline]
 process_backlog+0x756/0x10e0 net/core/dev.c:5923
 napi_poll net/core/dev.c:6346 [inline]
 net_rx_action+0x78b/0x1a60 net/core/dev.c:6412
 __do_softirq+0x53f/0x93a kernel/softirq.c:293
 do_softirq_own_stack+0x49/0x80 arch/x86/entry/entry_64.S:1039
 </IRQ>
 do_softirq kernel/softirq.c:338 [inline]
 __local_bh_enable_ip+0x16f/0x1a0 kernel/softirq.c:190
 local_bh_enable+0x36/0x40 include/linux/bottom_half.h:32
 rcu_read_unlock_bh include/linux/rcupdate.h:696 [inline]
 ip6_finish_output2+0x1d64/0x25f0 net/ipv6/ip6_output.c:121
 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
 NF_HOOK_COND include/linux/netfilter.h:278 [inline]
 ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
 dst_output include/net/dst.h:444 [inline]
 ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211
 __do_sys_sendmmsg net/socket.c:2240 [inline]
 __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x457ec9
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f4a5204fc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000457ec9
RDX: 00000000040001ab RSI: 0000000020000240 RDI: 0000000000000003
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4a520506d4
R13: 00000000004c4ce5 R14: 00000000004d85d8 R15: 00000000ffffffff

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline]
 kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159
 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
 slab_post_alloc_hook mm/slab.h:446 [inline]
 slab_alloc_node mm/slub.c:2754 [inline]
 __kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4377
 __kmalloc_reserve net/core/skbuff.c:140 [inline]
 __alloc_skb+0x309/0xa20 net/core/skbuff.c:208
 alloc_skb include/linux/skbuff.h:1012 [inline]
 alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5288
 sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091
 sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108
 __ip6_append_data+0x42ed/0x5dc0 net/ipv6/ip6_output.c:1443
 ip6_append_data+0x3c2/0x650 net/ipv6/ip6_output.c:1619
 icmp6_send+0x2f5c/0x3c40 net/ipv6/icmp.c:574
 icmpv6_send+0xe5/0x110 net/ipv6/ip6_icmp.c:43
 ip6_link_failure+0x5c/0x2c0 net/ipv6/route.c:2231
 dst_link_failure include/net/dst.h:427 [inline]
 vti_xmit net/ipv4/ip_vti.c:229 [inline]
 vti_tunnel_xmit+0xf3b/0x1ea0 net/ipv4/ip_vti.c:265
 __netdev_start_xmit include/linux/netdevice.h:4382 [inline]
 netdev_start_xmit include/linux/netdevice.h:4391 [inline]
 xmit_one net/core/dev.c:3278 [inline]
 dev_hard_start_xmit+0x604/0xc40 net/core/dev.c:3294
 __dev_queue_xmit+0x2e48/0x3b80 net/core/dev.c:3864
 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3897
 neigh_direct_output+0x42/0x50 net/core/neighbour.c:1511
 neigh_output include/net/neighbour.h:508 [inline]
 ip6_finish_output2+0x1d4e/0x25f0 net/ipv6/ip6_output.c:120
 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154
 NF_HOOK_COND include/linux/netfilter.h:278 [inline]
 ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171
 dst_output include/net/dst.h:444 [inline]
 ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176
 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727
 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169
 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466
 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116
 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211
 __do_sys_sendmmsg net/socket.c:2240 [inline]
 __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237
 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Fixes: b8a51b38 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 1c25324c ("net/sched: act_tunnel_key: Don't dump dst port
if it wasn't set"), act_tunnel_key doesn't dump anymore the destination
port, unless it was explicitly configured. This caused systematic failures
in the following TDC test case:

 7a88 - Add tunnel_key action with cookie parameter

Avoid matching zero values of TCA_TUNNEL_KEY_ENC_DST_PORT to let the test
pass again.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After merge of commit 80ef0f22 ("net/sched: act_tunnel_key: Allow
key-less tunnels"), act_tunnel_key does not reject anymore requests to
install 'set' rules where the key id is missing. Therefore, drop the
following TDC testcase:

 ba4e - Add tunnel_key set action with missing mandatory id parameter

because it's going to become a systematic fail as soon as userspace
iproute2 will start supporting key-less tunnels.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().

Fixes: 424ca4c5 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.

Fixes: e4cf8a38 ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 65cab850 ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.

Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850 ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>