The patch below fixes a warning message Im seeing with gcc 4.6.0
 CC [M]  drivers/net/wireless/hostap/hostap_main.o
drivers/net/wireless/hostap/hostap_main.c: In function 'hostap_set_multicast_list_queue':
drivers/net/wireless/hostap/hostap_main.c:744:27: warning: variable 'iface' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	net/mac80211/mlme.c

regression introduced by b8d92c9c

In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function

this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reviewed RX descriptor functions against the HAL sources. Some minor changes:

  - check size before making changes to the descriptor

  - whitespace

  - add comments about 5210 timestamps. this needs to be adressed later!

  - FIFO overrun error only available on 5210

  - rs_phyerr should not be OR'ed

  - clear the whole ath5k_rx_status structure before using, instead of
    zeroing specific fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.

Add 5211 specific frame types.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I carefully reviewed desh.h against the HAL sources. Added comments and made
differences between 5210, 5211 and 5212 more clear by adding _521x to the
defines which are specific to that chipset. Renamed some defines. No functional
changes.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k_hw_rx_error was only used once, where we could easily just use
ath5k_hw_rx_status as well, so remove it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Just whitespace and indentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use direct function calls for ath5k_hw_setup_rx_desc() and
ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed
to the same function in the case of ath5k_hw_setup_rx_desc() and which is
easily unified in the case of ath5k_hw_setup_mrr_tx_desc().

Also simplify the initialization function for the remaining function pointers.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Create a new function ath5k_receive_frame_ok() which checks for errors, updates
error statistics and tells us if we want to further "receive" this frame or
not. This way we can avoid a goto and have a cleaner separation between buffer
handling and other things.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move frame reception into it's own function to have a clearer separation
between buffer and descriptor handling and things that are done when we
actually receive a frame.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no reason for a special handling (return) here, just break like we do
with the checks before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After we free skbs for receive or transmit descriptors, make sure we have no
pointers to the now invalid memory address.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also
make the debug message more clear.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix comment about dma sizes, brackets were missing. Replace 'insure' with
'ensure'.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does:
it frees the skb and not the buf. Same for ath5k_rxbuf_free().
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a debug print for every case of reset.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

BugLink: http://bugs.launchpad.net/bugs/21367

Enable LED by default and update the MODULE_PARM_DESC.  The original
reason for defaulting to disabled was documented in 2005 and noted, "The
LED code has been reported to hang some systems when running ifconfig
and is therefore disabled by default."  This no longer appears
applicable and users have been requesting this be enabled for several
years.
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Medion MD40900 device id [0x0cde, 0x0006] is defined twice.
Comment out the duplicate.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ZD_REGDOMAIN_JAPAN_ADD and ZD_REGDOMAIN_JAPAN_GW_US54GXS seem a little
verbose to me...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

0x49 is used by PLANEX GW-US54GXS (2019:5303).
Signed-off-by: Kouhei Sutou <kou@clear-code.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now that ampdu_action() can sleep, remove all
the driver hacks and just issue WMI commands
to the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IBSS requires the cwmin and cwmax to be respected when
we reset the txqueues on AR9003 otherwise the distribution
of beacons will be balanced towards the AR9003 card first
preventing equal contention for air time for other peers
on the IBSS.

Without this IBSS will work but only the AR9003 card will be
be issuing beacons on the IBSS.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Legacy rt2870 driver handles WCID differently then we expected,
the BSSID and Cipher value are 3 bit values, while the 4th bit
should be set elsewhere in an extended field.

After this, rt2800usb reports frames have been decrypted
successfully, indicating that the Hardware decryption now is
working correctly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Hardware cryptography seems to be working
on a 11G network with WPA/WPA2 cryptography
enabled. WEP still needs to be tested...
Signed-of-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Similar to rt2800pci, remove the check for duplicate
register reading, and instead limit the for-loop to
the maximum number of TX entries inside a queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800lib has been under development of the rt2x00 project,
so add it to the author string for the module information.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Explicitly enable the usage of fallback rates for
the transmission of frames with rt61pci and rt73usb hardware.

Note that for txdone reporting, only rt61pci is capable of
reporting the fallback rates, for USB it is not possible
to determine the number of retries. However the device will
use the fallback rates, so it might still help in the performance.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In some corner cases the reported tx rates/retries didn't match the really
used ones.

The hardware lowers the tx rate on each consecutive retry by 1 (but won't
fall back from MCS to legacy rates) _until_ it reaches the lowest one.

In case the frame wasn't sent succesful the number of retries is 7 and if
a rate index <7 was used the previous code reported negative rate indexes
which were then ignored by the rate control algorithm and mac80211.

Instead, report the remaining number of retries to have happened with
the lowest rate (index 0). This should give the rate control algorithm
slightly more accurate information about the used tx rates/retries.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set up max_rates and max_rate_tries with suitable values even if we do not
support the whole functionality.

As rt2800 has a global fallback table we cannot specify more then one tx rate
per frame but since the hw will try several different rates (based on the
fallback table) we should still initialize max_rates to the maximum number of
rates we are going to try. Otherwise mac80211 will truncate our reported tx
rates and the rc algortihm will end up with incorrect data choosing unsuitable
rates for tx.

This improves throughput on rt2800 devices considerable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix typo in rt2800_config_txpower.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently rt2800pci will read TX_STA_FIFO until the previously read value
matches the current value. However, it is obvious that TX_STA_FIFO only
contains values that can easily be the same for multiple consecutive frames
(especially when communicating with only one other STA). Hence, we often
ended up with reading only the first entry and ignoring the rest.

One result was that when the TX_STA_FIFO contained multiple entires, only
the first one was read and properly handled while the others remained in the
tx queue.

Thus, drop this check but introduce a maximum number of reads. All legacy
drivers use the size of the tx ring as limit but state that the TX_STA_FIFO
has only 16 entries. So, let's just stick with the tx ring size for now.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a comment about the meaning of BBP1_TX_POWER stating all possible values.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IEEE80211_TX_CTL_MORE_FRAMES indicates that more frames are queued for tx
but has nothing to do with fragmentation. Hence, don't set ENTRY_TXD_MORE_FRAG
but only ENTRY_TXD_BURST to not kick the tx queues immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TXDONE_FALLBACK expresses that fallback rates were used for retries. Hence,
it only makes sense to set the flag if retries > 0.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TXDONE_FALLBACK doesn't express if the frame was sent successful or not. It
only tells us that the hw used fallback rates for retries. Hence, don't use
TXDONE_FALLBACK as success indicator.

Before this patch we reported success to the rate control algorithm which
was wrong in a number of cases and might have lead to improper tx rate
selections.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update the documentation of the available txdone flags to better express
how they should be used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>