Add usb dmac and hsusb device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add USB2.0 phy and host (EHCI/OHCI) device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc9 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0 ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add sound support for the RZ/G2M SoC (a.k.a. R8A774A1).

This work is based on similar work done on the R8A7796 SoC
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds PWM[0123456] device nodes to the RZ/G2M (a.k.a R8A774A1)
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.

Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all MSIOF SPI controllers on RZ/G2M SoC.

Based on several similar patches of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>
and Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add r8a774a1 IPMMU nodes.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add thermal support for R8A774A1 (RZ/G2M) SoC.

Based on the work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the I2C[0-6] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774a1 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SDHI nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO device nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds pinctrl device node for R8A774A1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add sys-dmac[0-2] device nodes for RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Condor/V3HSK board dependent parts of the DU and  LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the eMMC chip support for the V3M Started Kit board.

Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A77970 part of the MMC0 (SDHI2) device node.

Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds OPPs table for CA57{0,1} cpu devices
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
[simon: do not give nodes unit names as they have no bus addresses]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Allow the bare M3-N-based ULCB board to boot.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN
interfaces, similar to H3, M3-W and other SoCs from the same family.

Add CAN placeholder nodes to avoid below DTC errors:
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found

These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts.
Fix them beforehand.

CAN support is inspired from below commits:
 - v4.7 commit 308b7e4b ("arm64: dts: r8a7795: Add CAN support")
 - v4.11 commit 909c1625 ("arm64: dts: r8a7796: Add CAN support")
 - v4.12 commit bec0948e ("arm64: dts: r8a7796: Add reset control properties")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[simon: make placeholder minimal by only including reg property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Basic support for the RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Ensure that the ADV748x device addresses do not conflict, and group them
together (visually in i2cdetect)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the CSI2 and VIN (and their interconnections) in the R8A77980
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the nodes to enable SATA. Note that MD12 (SW12-7) must be switched
off for that to work.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds SATA controller node for the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The CAN clock node should precede the "cpus" node in the R8A779{7|8}0
device  trees,  according to  the alphanumeric node sorting rule...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The IPMMU nodes should follow the GEther node, not the CAN-FD node,
according to the <unit-address> part of the startng IPMMU-DS1 node.
While moving the nodes, also do sort them by label alphanumerically...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the performance monitor unit (PMU) for the Cortex-A53 cores in
the R8A77980 SoC's device tree.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.

Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe RWDT in the R8A77980 SoC device tree.

Enable RWDT on the Condor and V3H Starter Kit boards.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Pull timer update from Thomas Gleixner:
 "New defines for the compat time* types so they can be shared between
  32bit and 64bit builds. Not used yet, but merging them now allows the
  actual conversions to be merged through different maintainer trees
  without dependencies

  We still have compat interfaces for 32bit on 64bit even with the new
  2038 safe timespec/val variants because pointer size is different. And
  for the old style timespec/val interfaces we need yet another 'compat'
  interface for both 32bit native and 32bit on 64bit"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  y2038: Provide aliases for compat helpers