In host slave mode, the core asserts the rxready, txfifoempty interrupts
that get serviced in the gadget irq handler. Prevent servicing of these
when not in the gadget mode of operation.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Replaced the WARN_ON with a check and return of -EINVAL in the
dwc2_hsotg_ep_enable function if ep0 is passed in.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.

In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Coccinelle caught this instance of us kfree()ing
devm-allocated memory. The solution is just to not
do anything in our gadget_release.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When binding the function to usb_configuration, check whether the thread
is running before starting another one.  Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver.  This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.

This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.

This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).

N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice.  Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.

¹ I have no example failure though.  Conclusion that legacy/multi has
  a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.

This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.

Commit 342f39a6 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.

Fixes: c993c39b ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This function compiles to 298 bytes of machine code, has ~10 callsites.

This is a USB 2.0 device, USB 2.0 is limited to ~40 MB/s, so should be
almost never CPU bound. No need to optimize for speed this agressively.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felipe Balbi <balbi@ti.com>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The previous code could use the first USB-DMAC with IPMMU if iommus
property was set into this device node. However, in this case, it
could not control the second USB-DMAC with IPMMU because a parameter
of IPMMU (micro-TLB id) is different with each USB-DMAC.

So, this patch uses the usb_gadget_{un}map_request_by_dev() APIs for
IPMMU. (Then, iommus property should be set into USB-DMAC node(s).)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since usbhsg_dma_map_ctrl() needs DMA device structure in the near future,
this patch changes arguments of dma_map_ctrl() to give such data.
(This patch is only change the argument.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since usbhsf_dma_{un}map() will use the "fifo" data in the near future,
this patch changes function call orfer in usbhsf_dma_prepare_push().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the following environment, the first argument of DMA API should
be set to a DMAC's device structure, not a udc controller's one.
 - A udc controller needs an external DMAC device (like a DMA Engine).
 - The external DMAC enables IOMMU.

So, this patch add usb_gadget_{un}map_request_by_dev() API to set
a DMAC's device structure by a udc controller driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.

Fixes: 7ace8fc8 ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>

[felipe.balbi@linux.intel.com :
	- remove out-of-memory message, we get that from OOM.
	- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

trace already adds a newline character for us, we
don't need to do it ourselves.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.

It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:

	enqueue++ % 256;

gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

No functional changes. Merely adding useful
documentation for future readers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.

Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add snps,dis_rxdet_inp3_quirk property which disables receiver detection
in PHY P3 power state.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

we will need this from StartTransfer to make sure
link is in U0 before starting a transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.

This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.

Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Sort IDs in groups to be easily found when needed.

There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It seems there are leftovers of some assignments which are not used
anymore.  Compiler even warns us about:

drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]

drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]

Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>