The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C.  This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:

WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W    3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
 r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
 r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
 r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
 r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
 r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W    3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>]    lr : [<c03e88e4>]    psr: 60000013
sp : df883b50  ip : df883b78  fp : df883b74
r10: c11f4c54  r9 : c0836450  r8 : df30c400
r7 : fffffff4  r6 : df2ef410  r5 : 00000000  r4 : df2c3010
r3 : 00000000  r2 : 00000000  r1 : df86b0a0  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 2f29404a  DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
 r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
 r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---

Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device descriptors are messed up after remote wakeup
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 9b0a1de3.

Aaro writes:
	With v3.12-rc4 I can no longer connect to N800 (OMAP2) with USB
	(peripheral, g_ether).

	According to git bisect this is caused by:

	9b0a1de3 is the first bad commit

So revert this patch, as Felipe says:
	It's unfortunate that tusb6010 is so messed up
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device is not responsive when resumed, unless it is reset.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Without this change, the USB cable for Freestyle Option and compatible
glucometers will not be detected by the driver.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2013-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Pull xhci USB fixes from Sarah:

xhci: Bug fixes and quirks for 3.12

Hi Greg,

Here's four patches for 3.12.

The first patch is a bug fix for the USB 2.0 Link PM registers that I sent
out to the list a long time ago (August), but forgot to queue up.  The
second and fourth patches are quirks for xHCI hosts.  These patches are
marked for stable.  The third patch fixes a bug uncovered with sparse.

Sarah Sharp

Merge tag 'fixes-for-v3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Pull USB gadget fixes from Felipe:

usb: musb: fix for v3.12-rc

A single patch fixing musb start when using peripheral
only configurations. It turns out that musb_start() needs
to be called for peripheral too, so that function is
factored out of musb_virthub.c and into musb_core.c since
it's shared for both roles.
Signed-of-by: Felipe Balbi <balbi@ti.com>

I have am335x-evm with one port running in OTG mode. Since commit
fe4cb091 ("usb: musb: gadget: remove hcd initialization") the loaded
gadget does non pop up on the host. All I see is
|usb 4-5: new high-speed USB device number 52 using ehci-pci
|usb 4-5: device descriptor read/64, error -110

Since a later commit 2cc65fea ("usb: musb: add musb_host_setup() and
musb_host_cleanup()) the gadget shows up on the host again but only
in OTG mode (because we have the host init code running). It does not
work in device only mode.
If running in OTG mode and the gadget is removed and added back (rmmod
followed by modprobe of a gadget) then the same error is pops up on the
host side.

This patch ensures that the gadget side also executes musb_start() which
puts the chip in "connect accept" mode. With this change the device
works in OTG & device mode and the gadget can be added & removed
multiple times.
A device (if musb is in OTG mode acting as a host) is only recognized if
it is attached during module load (musb_hdrc module). After the device
unplugged and plugged again the host does not recognize it. We get a
buch of errors if musb running in OTG mode, attached to a host and no
gadget is loaded. Bah.
This is one step forward. Host & device only mode should work. I will
look at OTG later. I looked at this before commit fe4cb091 and OTG wasn't
working there perfectly so I am not sure that it is a regression :)

Cc: <stable@vger.kernel.org> # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally.  After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).

This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.

The PCI D3 call is based on the initial fix patch by Oliver Neukum.

[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them.  Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]

This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443a "xhci: Add
Lynx Point to list of Intel switchable hosts."

Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The function pci_write_config_dword() sets the appropriate byteordering
internally so the value argument should not be converted to little-endian.
This bug was found by sparse.

This patch is not suitable for stable.  Since cpu_to_lei32 is a no-op on
little endian systems, this bug would only affect big endian Intel
systems with the EHCI to xHCI port switchover, which are non-existent,
AFAIK.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

It has been reported that this chipset really cannot
sleep without this extraordinary delay.

This patch should be backported, in order to ensure this host functions
under stable kernels.  The last quirk for Fresco Logic hosts (commit
bba18e33 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The RWE bit of the USB 2.0 PORTPMSC register is supposed to enable
remote wakeup for devices in the lower power link state L1.  It has
nothing to do with the device suspend remote wakeup from L2.  The RWE
bit is designed to be set once (when USB 2.0 LPM is enabled for the
port) and cleared only when USB 2.0 LPM is disabled for the port.

The xHCI bus suspend method was setting the RWE bit erroneously, and the
bus resume method was clearing it.  The xHCI 1.0 specification with
errata up to Aug 12, 2012 says in section 4.23.5.1.1.1 "Hardware
Controlled LPM":

"While Hardware USB2 LPM is enabled, software shall not modify the
HIRDBESL or RWE fields of the USB2 PORTPMSC register..."

If we have previously enabled USB 2.0 LPM for a device, that means when
the USB 2.0 bus is resumed, we violate the xHCI specification by
clearing RWE.  It also means that after a bus resume, the host would
think remote wakeup is disabled from L1 for ports with USB 2.0 Link PM
enabled, which is not what we want.

This patch should be backported to kernels as old as 3.2, that
contain the commit 65580b43 "xHCI: set
USB2 hardware LPM".  That was the first kernel that supported USB 2.0
Link PM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target fixes queued up for v3.12-rc4 code.

  The highlights include:

   - Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
   - Allow sess_cmd_map allocation failure fallback to use vzalloc
   - Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
   - Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
     zero scsi_status bug
   - Make iscsi-target do acknowledgement tag release from RX context
   - Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags

  Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
  legacy wait_for_task=true release during fast-past StatSN
  acknowledgement, and two other SRP target related patches that address
  long-standing issues that are CC'ed for v3.3+.

  Extra thanks to Thomas Glanzmann for his testing feedback with
  COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
  iscsi-target: Perform release of acknowledged tags from RX context
  iscsi-target: Only perform wait_for_tasks when performing shutdown
  target: Fail on non zero scsi_status in compare_and_write_callback
  target: Fix recursive COMPARE_AND_WRITE callback failure
  target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
  ib_srpt: always set response for task management
  target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
  vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
  ib_srpt: Destroy cm_id before destroying QP.
  target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the slave dmanegine fixes.  We have the fix for deadlock issue
  on imx-dma by Michael and Josh's edma config fix along with author
  change"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: imx-dma: fix callback path in tasklet
  dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
  dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
  dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
  edma: Update author email address

Pull btrfs fixes from Chris Mason:
 "This is a small collection of fixes, including a regression fix from
  Liu Bo that solves rare crashes with compression on.

  I've merged my for-linus up to 3.12-rc3 because the top commit is only
  meant for 3.12.  The rest of the fixes are also available in my master
  branch on top of my last 3.11 based pull"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Fix crash due to not allocating integrity data for a bioset
  Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
  Btrfs: eliminate races in worker stopping code
  Btrfs: fix crash of compressed writes
  Btrfs: fix transid verify errors when recovering log tree

Pull GPIO fixes from Linus Walleij:
 "Two patches for the OMAP driver, dealing with setting up IRQs properly
  on the device tree boot path"

* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/omap: auto-setup a GPIO when used as an IRQ
  gpio/omap: maintain GPIO and IRQ usage separately

Pull USB fixes from Greg KH:
 "Here are none fixes for various USB driver problems.  The majority are
  gadget/musb fixes, but there are some new device ids in here as well"

* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: add Intel Clovertrail pci id
  usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
  usb: gadget: f_fs: fix error handling
  usb: musb: dsps: do not bind to "musb-hdrc"
  USB: serial: option: Ignore card reader interface on Huawei E1750
  usb: musb: gadget: fix otg active status flag
  usb: phy: gpio-vbus: fix deferred probe from __init
  usb: gadget: pxa25x_udc: fix deferred probe from __init
  usb: musb: fix otg default state

Pull tty fixes from Greg KH:
 "Here are two tty driver fixes for 3.12-rc4.

  One fixes the reported regression in the n_tty code that a number of
  people found recently, and the other one fixes an issue with xen
  consoles that broke in 3.10"

* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  xen/hvc: allow xenboot console to be used again
  tty: Fix pty master read() after slave closes

Pull staging fixes from Greg KH:
 "Here are 4 tiny staging and iio driver fixes for 3.12-rc4.  Nothing
  major, just some small fixes for reported issues"

* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
  iio:magnetometer: Bugfix magnetometer default output registers
  iio: Remove debugfs entries in iio_device_unregister()
  iio: amplifiers: ad8366: Remove regulator_put

When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
 IP: [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 PGD 2305e4067 PUD 23063d067 PMD 0
 Oops: 0000 [#1] PREEMPT SMP
 Modules linked in: btrfs scsi_debug xfs ext4 jbd2 ext3 jbd mbcache
sch_fq_codel eeprom lpc_ich mfd_core nfsd exportfs auth_rpcgss af_packet
raid6_pq xor zlib_deflate libcrc32c [last unloaded: scsi_debug]
 CPU: 1 PID: 4486 Comm: mount Not tainted 3.12.0-rc1-mcsum #2
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 task: ffff8802451c9720 ti: ffff880230698000 task.ti: ffff880230698000
 RIP: 0010:[<ffffffff8111e28a>]  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 RSP: 0018:ffff880230699688  EFLAGS: 00010286
 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000005f8445
 RDX: 0000000000000001 RSI: 0000000000000010 RDI: 0000000000000000
 RBP: ffff8802306996f8 R08: 0000000000011200 R09: 0000000000000008
 R10: 0000000000000020 R11: ffff88009d6e8000 R12: 0000000000011210
 R13: 0000000000000030 R14: ffff8802306996b8 R15: ffff8802451c9720
 FS:  00007f25b8a16800(0000) GS:ffff88024fc80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000018 CR3: 0000000230576000 CR4: 00000000000007e0
 Stack:
  ffff8802451c9720 0000000000000002 ffffffff81a97100 0000000000281250
  ffffffff81a96480 ffff88024fc99150 ffff880228d18200 0000000000000000
  0000000000000000 0000000000000040 ffff880230e8c2e8 ffff8802459dc900
 Call Trace:
  [<ffffffff811b2208>] bio_integrity_alloc+0x48/0x1b0
  [<ffffffff811b26fc>] bio_integrity_prep+0xac/0x360
  [<ffffffff8111e298>] ? mempool_alloc+0x58/0x150
  [<ffffffffa03e8041>] ? alloc_extent_state+0x31/0x110 [btrfs]
  [<ffffffff81241579>] blk_queue_bio+0x1c9/0x460
  [<ffffffff8123e58a>] generic_make_request+0xca/0x100
  [<ffffffff8123e639>] submit_bio+0x79/0x160
  [<ffffffffa03f865e>] btrfs_map_bio+0x48e/0x5b0 [btrfs]
  [<ffffffffa03c821a>] btree_submit_bio_hook+0xda/0x110 [btrfs]
  [<ffffffffa03e7eba>] submit_one_bio+0x6a/0xa0 [btrfs]
  [<ffffffffa03ef450>] read_extent_buffer_pages+0x250/0x310 [btrfs]
  [<ffffffff8125eef6>] ? __radix_tree_preload+0x66/0xf0
  [<ffffffff8125f1c5>] ? radix_tree_insert+0x95/0x260
  [<ffffffffa03c66f6>] btree_read_extent_buffer_pages.constprop.128+0xb6/0x120
[btrfs]
  [<ffffffffa03c8c1a>] read_tree_block+0x3a/0x60 [btrfs]
  [<ffffffffa03caefd>] open_ctree+0x139d/0x2030 [btrfs]
  [<ffffffffa03a282a>] btrfs_mount+0x53a/0x7d0 [btrfs]
  [<ffffffff8113ab0b>] ? pcpu_alloc+0x8eb/0x9f0
  [<ffffffff81167305>] ? __kmalloc_track_caller+0x35/0x1e0
  [<ffffffff81176ba0>] mount_fs+0x20/0xd0
  [<ffffffff81191096>] vfs_kern_mount+0x76/0x120
  [<ffffffff81193320>] do_mount+0x200/0xa40
  [<ffffffff81135cdb>] ? strndup_user+0x5b/0x80
  [<ffffffff81193bf0>] SyS_mount+0x90/0xe0
  [<ffffffff8156d31d>] system_call_fastpath+0x1a/0x1f
 Code: 4c 8d 75 a8 4c 89 6d e8 45 89 e0 4c 8d 6f 30 48 89 5d d8 41 83 e0 af 48
89 fb 49 83 c6 18 4c 89 7d f8 65 4c 8b 3c 25 c0 b8 00 00 <48> 8b 73 18 44 89 c7
44 89 45 98 ff 53 20 48 85 c0 48 89 c2 74
 RIP  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
  RSP <ffff880230699688>
 CR2: 0000000000000018
 ---[ end trace 7a96042017ed21e2 ]---
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

Pull CIFS fixes from Steve French:
 "Small set of cifs fixes.  Most important is Jeff's fix that works
  around disconnection problems which can be caused by simultaneous use
  of user space tools (starting a long running smbclient backup then
  doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
  Jim's fix to deal with reexport of cifs share.

  I expect to send two more cifs fixes next week (being tested now) -
  fixes to address an SMB2 unmount hang when server dies and a fix for
  cifs symlink handling of Windows "NFS" symlinks"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] update cifs.ko version
  [CIFS] Remove ext2 flags that have been moved to fs.h
  [CIFS] Provide sane values for nlink
  cifs: stop trying to use virtual circuits
  CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them

Pull PCI fix from Bjorn Helgaas:
 "We merged what was intended to be an MMCONFIG cleanup, but in fact,
  for systems without _CBA (which is almost everything), it broke
  extended config space for domain 0 and it broke all config space for
  other domains.

  This reverts the change"

* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"

This reverts commit 07f9b61c.

07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.

Reference: http://lkml.kernel.org/r/20131004011806.GE20450@dangermouse.emea.sgi.comReported-by: Hedi Berriche <hedi@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull ACPI and power management fixes from Rafael Wysocki:

 - The resume part of user space driven hibernation (s2disk) is now
   broken after the change that moved the creation of memory bitmaps to
   after the freezing of tasks, because I forgot that the resume utility
   loaded the image before freezing tasks and needed the bitmaps for
   that.  The fix adds special handling for that case.

 - One of recent commits changed the export of acpi_bus_get_device() to
   EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
   binary modules using that function including one in particularly
   widespread use.  Change it back to EXPORT_SYMBOL().

 - The intel_pstate driver sometimes fails to disable turbo if its
   no_turbo sysfs attribute is set.  Fix from Srinivas Pandruvada.

 - One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
   which still (incorrectly) treats non-NULL as non-error.  Fix from
   Philipp Zabel.

 - The SPEAr cpufreq driver uses a wrong variable type in one place
   preventing it from catching errors returned by one of the functions
   called by it.  Fix from Sachin Kamat.

* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
  intel_pstate: fix no_turbo
  cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
  cpufreq: SPEAr: Fix incorrect variable type
  PM / hibernate: Fix user space driven resume regression

Pull xfs bugfixes from Ben Myers:
 "There are lockdep annotations for project quotas, a fix for dirent
  dtype support on v4 filesystems, a fix for a memory leak in recovery,
  and a fix for the build error that resulted from it.  D'oh"

* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
  xfs: Use kmem_free() instead of free()
  xfs: fix memory leak in xlog_recover_add_to_trans
  xfs: dirent dtype presence is dependent on directory magic numbers
  xfs: lockdep needs to know about 3 dquot-deep nesting

Now avc_audit() has no more users with that parameter. Remove it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.. so get rid of it.  The only indirect users were all the
avc_has_perm() callers which just expanded to have a zero flags
argument.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents.  Fix this by
zeroing the superblock before the rcu callback is registered.

Cc: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop.  The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.

E.g., check_idle_worker race flow:

       btrfs_stop_workers():            check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
  working list
- removes the first worker from the
  working list
- releases the lock to wait for
  its kthread's completion
                                  - grabs the lock
                                  - if aworker is on the working list,
                                    moves aworker from the working list
                                    to the idle list
                                  - releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
  working list
                              ......
        btrfs_stop_workers returns, aworker is on the idle list
                 FS is umounted, memory is freed
                              ......
              aworker is waken up, fireworks ensue

With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.

The bug is quite interesting, it's actually introduced by a recent commit
(573aecaf,
Btrfs: actually limit the size of delalloc range).

Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
    ordered extent and so on.
(4) submit the page A.

It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).

The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).

This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.

This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.

[1]:
------------[ cut here ]------------
kernel BUG at mm/page-writeback.c:2170!
[...]
CPU: 2 PID: 11755 Comm: btrfs-delalloc- Tainted: G           O 3.11.0+ #8
[...]
RIP: 0010:[<ffffffff810f5093>]  [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[...]
[ 4934.248731] Stack:
[ 4934.248731]  ffff8801477e5dc8 ffffea00049b9f00 ffff8801869f9ce8 ffffffffa02b841a
[ 4934.248731]  0000000000000000 0000000000000000 0000000000000fff 0000000000000620
[ 4934.248731]  ffff88018db59c78 ffffea0005da8d40 ffffffffa02ff860 00000001810016c0
[ 4934.248731] Call Trace:
[ 4934.248731]  [<ffffffffa02b841a>] extent_range_clear_dirty_for_io+0xcf/0xf5 [btrfs]
[ 4934.248731]  [<ffffffffa02a8889>] compress_file_range+0x1dc/0x4cb [btrfs]
[ 4934.248731]  [<ffffffff8104f7af>] ? detach_if_pending+0x22/0x4b
[ 4934.248731]  [<ffffffffa02a8bad>] async_cow_start+0x35/0x53 [btrfs]
[ 4934.248731]  [<ffffffffa02c694b>] worker_loop+0x14b/0x48c [btrfs]
[ 4934.248731]  [<ffffffffa02c6800>] ? btrfs_queue_worker+0x25c/0x25c [btrfs]
[ 4934.248731]  [<ffffffff810608f5>] kthread+0x8d/0x95
[ 4934.248731]  [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731]  [<ffffffff814fe09c>] ret_from_fork+0x7c/0xb0
[ 4934.248731]  [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731] Code: ff 85 c0 0f 94 c0 0f b6 c0 59 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 41 54 53 48 89 fb e8 2c de 00 00 49 89 c4 48 8b 03 a8 01 75 02 <0f> 0b 4d 85 e4 74 52 49 8b 84 24 80 00 00 00 f6 40 20 01 75 44
[ 4934.248731] RIP  [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[ 4934.248731]  RSP <ffff8801869f9c48>
[ 4934.280307] ---[ end trace 36f06d3f8750236a ]---
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount.  This is because we were not zero'ing out the log when we committed the
transaction after recovery.  This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery.  Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

Every single user passes in '0'.  I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.

See commit 2e334057 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>