There is no chance to wait spi message complete if failed to
prepare_transfer_hardware(). Therefore, finalize this message and abort
transfer with corresponding return status to release this block case.

Logs:

[17400.283005] c7   3267 PM: PM: suspend entry 2019-05-04 03:01:14.403097147 UTC
[17400.283013] c7   3267 PM: suspend entry (deep)
[17400.283016] c6   3267 PM: Syncing filesystems ... done.
[17400.584395] c1    753 spi_geni 890000.spi: spi_geni_prepare_transfer_hardware:Error enabling SE resources -13
[17400.584404] c1    753 spi_master spi1: failed to prepare transfer hardware
[17400.664611] c4   3267 PM: PM: suspend exit 2019-05-04 03:01:15.235273018 UTC

Flow:

__spi_sync@spi.c
|    if (status == 0) {
|        /* Push out the messages in the calling context if we
|         * can.
|         */
|        if (ctlr->transfer == spi_queued_transfer) {
|            SPI_STATISTICS_INCREMENT_FIELD(&ctlr->statistics,
|		spi_sync_immediate);
|            SPI_STATISTICS_INCREMENT_FIELD(&spi->statistics,
|		spi_sync_immediate);
|		__spi_pump_messages(ctlr, false);
|        }
|
|        wait_for_completion(&done);	<== stuck here!!!
|        status = message->status;
|    }
|    message->context = NULL;
|    return status;
|
-->	__spi_pump_messages@spi.c
	|    if (!was_busy && ctlr->prepare_transfer_hardware) {
	|        ret = ctlr->prepare_transfer_hardware(ctlr);
	|        if (ret) {
	|            dev_err(&ctlr->dev,
	|		"failed to prepare transfer hardware\n");
	|
	|        if (ctlr->auto_runtime_pm)
	|            pm_runtime_put(ctlr->dev.parent);
	|            mutex_unlock(&ctlr->io_mutex);
	|            return;
	|        }
	|    }
	|
	-->	spi_geni_prepare_transfer_hardware@spi-geni-qcom.c
		|    ret = pm_runtime_get_sync(mas->dev);
		|    if (ret < 0) {
		|        dev_err(mas->dev,
		|		"%s:Error enabling SE resources %d\n",
		|		__func__, ret);
		|    pm_runtime_put_noidle(mas->dev);
		|    goto exit_prepare_transfer_hardware;
Signed-off-by: Super Liu <supercjliu@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi_finalize_current_message() shall be called once all
actions are finished, otherwise the last actions might
step over a newly started transfer.

Fixes: c592becb ("spi: fsl-(e)spi: migrate to generic master queueing")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>

If spi_register_master fails in spi_bitbang_start
because device_add failure, We should return the
error code other than 0, otherwise calling
spi_bitbang_stop may trigger NULL pointer dereference
like this:

BUG: KASAN: null-ptr-deref in __list_del_entry_valid+0x45/0xd0
Read of size 8 at addr 0000000000000000 by task syz-executor.0/3661

CPU: 0 PID: 3661 Comm: syz-executor.0 Not tainted 5.1.0+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
 dump_stack+0xa9/0x10e
 ? __list_del_entry_valid+0x45/0xd0
 ? __list_del_entry_valid+0x45/0xd0
 __kasan_report+0x171/0x18d
 ? __list_del_entry_valid+0x45/0xd0
 kasan_report+0xe/0x20
 __list_del_entry_valid+0x45/0xd0
 spi_unregister_controller+0x99/0x1b0
 spi_lm70llp_attach+0x3ae/0x4b0 [spi_lm70llp]
 ? 0xffffffffc1128000
 ? klist_next+0x131/0x1e0
 ? driver_detach+0x40/0x40 [parport]
 port_check+0x3b/0x50 [parport]
 bus_for_each_dev+0x115/0x180
 ? subsys_dev_iter_exit+0x20/0x20
 __parport_register_driver+0x1f0/0x210 [parport]
 ? 0xffffffffc1150000
 do_one_initcall+0xb9/0x3b5
 ? perf_trace_initcall_level+0x270/0x270
 ? kasan_unpoison_shadow+0x30/0x40
 ? kasan_unpoison_shadow+0x30/0x40
 do_init_module+0xe0/0x330
 load_module+0x38eb/0x4270
 ? module_frob_arch_sections+0x20/0x20
 ? kernel_read_file+0x188/0x3f0
 ? find_held_lock+0x6d/0xd0
 ? fput_many+0x1a/0xe0
 ? __do_sys_finit_module+0x162/0x190
 __do_sys_finit_module+0x162/0x190
 ? __ia32_sys_init_module+0x40/0x40
 ? __mutex_unlock_slowpath+0xb4/0x3f0
 ? wait_for_completion+0x240/0x240
 ? vfs_write+0x160/0x2a0
 ? lockdep_hardirqs_off+0xb5/0x100
 ? mark_held_locks+0x1a/0x90
 ? do_syscall_64+0x14/0x2a0
 do_syscall_64+0x72/0x2a0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 702a4879 ("spi: bitbang: Let spi_bitbang_start() take a reference to master")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This reverts commit c9ba7a16 (Release spi_res after finalizing
message) which causes races during cleanup.
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

When GPIO chip-select is used nothing prevents any available SPI
controllers to work with both CS-high and traditional CS-low modes.
In fact the SPI bus core code already does it, so we don't need to
introduce any modification there. But spi_setup() still fails to
switch the interface settings if CS-high flag is set for the case
of GPIO-driven slave chip-select when the SPI controller doesn't
support the hardwired CS-inversion. Lets fix it by clearing the
SPI_CS_HIGH flag out from bad_bits (unsupported by controller) when
client chip is selected by GPIO.

This feature is useful for slave devices, which in accordance with
communication protocol can work with both active-high and active-low
chip-selects. I am aware of one such device. It is MMC-SPI interface,
when at init sequence the driver needs to perform a read operation with
low and high chip-select sequentially (requirement of 74 clock cycles
with both chipselect, see the mmc_spi driver for details).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.

EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.

Before this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias:          spi:adau1979
alias:          spi:adau1978
alias:          spi:adau1977

After this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias:          of:N*T*Cadi,adau1979C*
alias:          of:N*T*Cadi,adau1979
alias:          of:N*T*Cadi,adau1978C*
alias:          of:N*T*Cadi,adau1978
alias:          of:N*T*Cadi,adau1977C*
alias:          of:N*T*Cadi,adau1977
alias:          spi:adau1979
alias:          spi:adau1978
alias:          spi:adau1977
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

During probe, check the "get_irq" error value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Split spi transfers into chunks of <=65532 to enable the driver to
perform DMA transfer on big buffers. The DLEN register specifies the
number of bytes to transfer in DMA mode. It is 16-bit wide and thus the
maximum DMA transfer is 65535 bytes. Set the maximum to 65532 (4 byte
aligned) since the FIFO in DMA mode is accessed in 4 byte chunks.

->max_dma_len is the value the spi core uses when splitting the buffer
into scatter gather entries.
The BCM2835 DMA block has 2 types of channels/engines:
- Normal: Max length: 1G
- Lite: Max length: 65535

Even when using a Lite channel we will not exceed the max length, so
let's drop setting ->max_dma_len.
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch changes mode and mode_bits from u16 to u32 to allow more
mode configurations.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add binding documentation of spi-mt65xx for MT8516 SOC.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add PCI IDs for SPI on Comet Lake.
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Large transfers (64kB) doesn't show up in the trace. Not sure why, but
since printk can only display buffers up to 64 bytes in length, we only
need to store the first 64 bytes.

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi_split_transfers_maxsize() can be used to split a transfer. This
function uses spi_res to lifetime manage the added transfer structures.
So in order to finalize the current message while it contains the split
transfers, spi_res_release() must be called after finalizing.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Don't warn about splitting transfers, the info is available in the
statistics if needed.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Falling back to maximum speed of the controller in case of SPI slave
maximum speed is not set is needless. It already defaults to maximum
speed of the controller since commit 052eb2d4 ("spi: core: Set
max_speed_hz of spi_device default to max_speed_hz of controller").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>

With dw_dmac, sometimes the request of a DMA channel fails because
the DMA driver is not ready, so an explicit dependency request
is necessary.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>

Stub helper spi_mem_default_supports_op() should
be set to static inline
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When building with CONFIG_SPI_MEM is not set
gc warns this:

drivers/spi/spi-zynq-qspi.o: In function `zynq_qspi_supports_op':
spi-zynq-qspi.c:(.text+0x1da): undefined reference to `spi_mem_default_supports_op'

Fixes: 67dca5e5 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Tegra SPI controller has TX and RX trimmers to tuning the delay of
SPI master clock with respect to the data.

TX and RX tap values are based on the platform validation across the
PVT and the trimmer values vary based on the trace lengths to the
corresponding SPI devices.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch creates set_cs_timing SPI master optional method for
SPI masters to implement configuring CS timing if applicable.

This patch also creates spi_cs_timing accessory for SPI clients to
use for requesting SPI master controllers to configure device requested
CS setup time, hold time and inactive delay.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch documents set_cs_timing SPI master method.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch creates tegra_spi_soc_data structure to maintain and implement
SPI HW feature differences between different Tegra chips and also creates
a separate compatible string for T124/T210.

Tegra210 and later has a separate interrupt mask register SPI_INTR_MASK
for enabling or disabling interrupts while Tegra124 and prior uses
interrupt enable bits in SPI_DMA_CTL register.

This patch creates flag has_intr_mask_reg in tegra_spi_soc_data to
identify this and implements accordingly.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds 3 wire transfer support to SPI mode list along with
its implementation.

3 wire or Bi-directional mode uses only one serial data pin for the
transfer. SPI in master mode uses MOSI data line only and MISO data
line is not used.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds support for dual mode SPI transfer.

Dual mode uses both MOSI and MISO lines in parallel where the data
is interleaved on MOSI and MISO lines increasing the throughput.

Packet from Tx FIFO is transmitted on both MOSI and MISO lines and
packet to Rx FIFO is received from both MOSI and MISO lines. Even
bits are transmitted or received on the MOSI data line and odd bits
are transmitted or received on the MISO data line.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Replace spi_bitbang_start() with a combination of spi_bitbang_init()
and devm_spi_register_master() and drop all of the explicit
cleanup-related code that's no longer necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Move all of the code doing struct spi_bitbang initialization, so that
it can be paired with devm_spi_register_master() in order to avoid
having to call spi_bitbang_stop() explicitly.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

There's a number of failure paths in spi_gpio_probe() that do not call
spi_master_put() potentially leaking memory. Fix this problem by
registering a cleanup funciont via devm_add_action_or_reset() right
after SPI controller is allocated.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Change the type of the diagnostic message:

"no DMA channels available, using PIO"

from debug to warning.

The lack of an available DMA channel is very important regard the
spi-pxa2xx performance. The transfer speed can be reduced more than 50%.

So it is very important to warn the user about this, without enabling
the full SPI debug with CONFIG_SPI_DEBUG.

Moreover, enabling the full SPI debug only to enable this specific
debug message, the dmesg buffer fills quickly with a lot of
repetitive information during the SPI data transfer.
This cause the loss of all the first important messages
written during the initialization.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use is_slave local variable to avoid calling of_property_read_bool() twice.
Remove redudant assignment for controller->bus_num, set it once is enough.
Move setting controller->bits_per_word_mask close to the code init other
controller fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add #ifdef CONFIG_PM guard to fix build warning when !CONFIG_PM
drivers/spi/spi-fsl-lpspi.c:810:12: warning: ‘fsl_lpspi_runtime_suspend’ defined but not used [-Wunused-function]
 static int fsl_lpspi_runtime_suspend(struct device *dev)
            ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-fsl-lpspi.c:789:12: warning: ‘fsl_lpspi_runtime_resume’ defined but not used [-Wunused-function]
 static int fsl_lpspi_runtime_resume(struct device *dev)
            ^~~~~~~~~~~~~~~~~~~~~~~~

Fixes: 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The original code already set controller as drvdata:
platform_set_drvdata(pdev, controller);

But commit 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
added dev_set_drvdata(&pdev->dev, fsl_lpspi);
so fsl_lpspi_remove() will get wrong pointer by platform_get_drvdata().

Fixes: 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The function names in the kernel-doc comments were mistyped, with a word
"dirmap" being repeated twice, so fix them.

Fixes: aa167f3f ("spi: spi-mem: Add a new API to support direct mapping")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When building CONFIG_DEBUG_FS is not set
gcc warn this:

drivers/spi/spi-bcm2835aux.c: In function bcm2835aux_spi_probe:
drivers/spi/spi-bcm2835aux.c:591:2: error: too many arguments to function bcm2835aux_debugfs_create
  bcm2835aux_debugfs_create(bs, dev_name(&pdev->dev));
  ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:145:13: note: declared here
 static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs)
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8048d151 ("spi: bcm2835aux: add driver stats to debugfs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The 'status' local variable is initialized but this value is never used,
thus kill that initializer.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for QSPI controller driver used by Xilinx Zynq SOC.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds the dts binding document for Zynq SOC QSPI controller.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There's no code using 'pdev' field in struct spi_gpio. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>