Add snd_ prefix to avoid the conflict of symbols in omac-mcbsp.c:
  sound/soc/omap/omap-mcbsp.c:503: error: static declaration of 'omap_mcbsp_init' follows non-static declaration
  arch/arm/plat-omap/include/mach/mcbsp.h:373: error: previous declaration of 'omap_mcbsp_init' was here
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The module init entries should be __init instead of __devinit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixed the function name of module init entry for twl4030.c, which
conflicted with the existing hardware init function:
  sound/soc/codecs/twl4030.c:1278: error: conflicting types for 'twl4030_init'
  sound/soc/codecs/twl4030.c:1187: error: previous definition of 'twl4030_init' was here

Also fixed the section type of init function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

I wish I had boards which work with unmodified kernels :/
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This makes use of the support for delayed DAI registration to allow the
WM8900 I2C device to be registered by general platform/architecture code
rather than as part of the ASoC device probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This will allow codec drivers to be refactored to allow them to be
registered out of line with the ASoC device registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use the lists of platforms, platform DAIs and cards to check to see that
everything has registered. Since relationships are still specified by
direct references to the structures in the drivers and the drivers all
register everything at modprobe there should be no practical effect yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently this is done at module probe time since ASoC ties in codec
device probe to the instantiation of the entire ASoC device. Subsequent
patches will refactor the codec drivers to handle probing separately.
Note that the core does not yet use this information.

AC97 is special since the codec is controlled over the AC97 link but
we want to give the machine driver a chance to set up the system before
trying to instantiate since it may need to do configuration before the
AC97 link will operate
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is done at modprobe time, mirroring current behaviour, except for
mpc5200_psc_i2s where we do registration at the same time as we register
with soc-of-simple. Since the core currently ignores registration this
has no practical impact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC v2 allows platform drivers to instantiate independantly of the
overall ASoC card. This API allows drivers to notify the core when
they are registered.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Register all platform DAIs with the core.  In line with current behaviour
this is done at module probe time rather than when the devices are probed
(since currently that only happens as the entire ASoC card is registered
except for those drivers that currently implement some kind of hotplug).
Since the core currently ignores DAI registration this has no practical
effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add API calls to register and unregister DAIs with the core.  Currently
these APIs are ineffective.  Since multiple DAIs for a given device are
a common case bulk variants are provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC v2 allows cards, codecs and platforms to instantiate separately,
with the overall ASoC device only being instantiated once all the
required components have registered. As part of backporting Liam's work
introduce an initial version of the card registration functions. At
present these do nothing active and are internal only, they will be
exposed to machine drivers after further backporting.  Adding this now
allows the datastructures used for dynamic card instantiation to be
built up gradually.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There is a separate gain control for the Headset output already.
Do not reset the gain to 0 dB at power up.
In power-down, there is no need to set the Headset output gain
to power-down mode, since if the CODECPDZ is in powered off this
setting has no effect.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds DAPM muxing, routing for the Handsfree outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds DAPM muxing, routing for the Carkit outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds DAPM muxing, routing for the Headset outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds DAPM muxing, routing for the PreDrive outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Adds DAPM muxing, routing for the Earpiece output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

DAPM event handler is set to filter out invalid MUX settings
for certain outputs.
Earpiece:
 - 0 = Off
 - 1 = DACL1
 - 2 = DACL2
 - 3 = *** Invalid ***
 - 4 = DACR1

PreDriveL/R:
 - 0 = Off/Off
 - 1 = DACL1/DACR1
 - 2 = DACL2/DACR2
 - 3 = *** Invalid/Invalid ***
 - 4 = DACR2/DACL2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add all four APGA switch to DAPM routing and widgets.
Add user control for DA enable for all APGA as normal
control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add all four DACs to dapm_widgets with power switch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

- split "Line Playback Switch" into "LineL Playback Switch" and "LineR
  Playback Switch"
- split "Line PGA Bypass Playback Volume" into "LineL Left PGA Bypass
  Playback Volume" and "LineR Right PGA Bypass Playback Volume"
- split "Line Line2 Bypass Playback Volume" into "LineL Line2 Bypass
  Playback Volume" and "LineR Line2 Bypass Playback Volume"
- Added "HP Right PGA Bypass Playback Volume"
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds basic support for OMAP3 Pandora.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The struct is never defined.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

None of the DAIs use it except s3c2412-i2s which only uses it for
dev_() printouts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

None of the platforms are actually using the SoC device so remove it
(only atmel actually has a suspend method).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is in preparation for the removal of struct snd_soc_device.

The pop time configuration should really be a property of the card not
the codec but since DAPM currently uses the codec rather than the card
using the codec is fine for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

- Add aic3x_set_headset_detection() function to define the headset
  detection mode for tlv32aic3x chips
- added aic3x_button_pressed()
- Read from the real-time registers in aic3x_headset_detected() to query
  headset presence without an occured interrupt
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The TWL4030 codec device has two ADCs. Both of them can have
several inputs routed to them, but TRM says that only one source
can be selected for every ADC, even though every source has a
dedicated bit in the registers.

This patch adds input source controls. It modifies default register
values to have no inputs selected and ADCs disabled. When some
input is selected, control handlers enable apropriate input
amplifier and ADC. If a microphone is selected, bias power is
automatically enabled. When some input is deselected, unused
chip parts are disabled.

Microphone and line input recording tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC v2 does not use the struct snd_soc_device at runtime, using struct
snd_soc_card as the root of the card.  Begin removing data from
snd_soc_device by pushing the workqueue data into snd_soc_card, using a
backpointer to the snd_soc_device to keep things going for the time
being.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

All outputs have dedicated gain controls except the
HandsFree output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add Playback volume controls for all four DACs.
All four paths has three levels of volume controls:
Digital Fine gain, Digital Coarse gain, Analog gain.

The controls are named to reflect their connection to the DACs.
Per DAC volume can be performed, if needed:
amixer sset 'DAC1 Analog'  5,10
DACL1 analog gain to 5
DACR1 analog gain to 10
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The digital Capture gain control has a range:
0 to 31 dB in 1 dB steps.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently ASoC card initialisation is completed by a function called
snd_soc_register_card().  As part of the work to allow independant
registration of cards, codecs and machines in ASoC v2 a new function of
the same name has been added so rename the existing function to
facilitate the merge of v2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>