Since commit 28c56ea1
(powerpc/usb: fix bug of kernel hang when initializing usb)
the kernel crashes on mpc5121e. mpc5121e doesn't have system interface
registers, accessing this register address space cause the machine check
exception and a kernel crash:
...
[    1.294596] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.316491] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    1.337334] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    1.358548] Machine check in kernel mode.
[    1.375917] Caused by (from SRR1=49030): Transfer error ack signal
[    1.395505] Oops: Machine check, sig: 7 [#1]
[    1.413113] MPC5121 ADS
[    1.428718] Modules linked in:
[    1.444841] NIP: c026efc4 LR: c0278b50 CTR: 00000000
[    1.463342] REGS: df837ba0 TRAP: 0200   Not tainted  (3.3.0-08839-gb5174fa3)
[    1.484083] MSR: 00049030 <EE,ME,IR,DR>  CR: 42042022  XER: 20000000
[    1.504099] TASK = df834000[1] 'swapper' THREAD: df836000
[    1.509667] GPR00: 1c000000 df837c50 df834000 df9d74e0 00000003 00000010 00000000 00000000
[    1.531650] GPR08: 00000020 00000000 c037cdd8 e1088000 22042028 1001a69c 00000000 00000000
[    1.553762] GPR16: 1ffbce70 00000000 1fef5b28 1fef3e08 00000000 00000000 1ffcbc7c c045b264
[    1.575824] GPR24: 0000008b 00000002 c04a7dd0 e1088000 df33c960 df9d74e0 00000000 df9d7400
[    1.612295] NIP [c026efc4] ehci_fsl_setup_phy+0x110/0x124
[    1.632454] LR [c0278b50] ehci_fsl_setup+0x29c/0x304
[    1.652065] Call Trace:
[    1.668923] [df837c50] [c0278a40] ehci_fsl_setup+0x18c/0x304 (unreliable)
[    1.690332] [df837c70] [c025cba4] usb_add_hcd+0x1f0/0x66c
[    1.710377] [df837cb0] [c0277ab8] ehci_fsl_drv_probe+0x180/0x308
[    1.731322] [df837ce0] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.752202] [df837cf0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.773491] [df837d10] [c01f956c] bus_for_each_drv+0x6c/0xa8
[    1.794279] [df837d40] [c01fafdc] device_attach+0xb4/0xd8
[    1.814574] [df837d60] [c01fa44c] bus_probe_device+0xa4/0xb4
[    1.835343] [df837d80] [c01f87a8] device_add+0x52c/0x5dc
[    1.855462] [df837dd0] [c01fcd58] platform_device_add+0x124/0x1d0
[    1.876558] [df837df0] [c036dcec] fsl_usb2_device_register+0xa0/0xd4
[    1.897512] [df837e10] [c036df28] fsl_usb2_mph_dr_of_probe+0x208/0x264
[    1.918253] [df837e90] [c01fc7a8] platform_drv_probe+0x20/0x30
[    1.938300] [df837ea0] [c01fb0ac] driver_probe_device+0x8c/0x214
[    1.958511] [df837ec0] [c01fb2f0] __driver_attach+0xbc/0xc0
[    1.978088] [df837ee0] [c01f9608] bus_for_each_dev+0x60/0x9c
[    1.997589] [df837f10] [c01fab88] driver_attach+0x24/0x34
[    2.016757] [df837f20] [c01fa744] bus_add_driver+0x1ac/0x274
[    2.036339] [df837f50] [c01fb898] driver_register+0x88/0x150
[    2.056052] [df837f70] [c01fcabc] platform_driver_register+0x68/0x78
[    2.076650] [df837f80] [c0446500] fsl_usb2_mph_dr_driver_init+0x18/0x28
[    2.097734] [df837f90] [c0003988] do_one_initcall+0x148/0x1b0
[    2.117934] [df837fc0] [c042d89c] kernel_init+0xfc/0x190
[    2.137667] [df837ff0] [c000d2c4] kernel_thread+0x4c/0x68
[    2.157240] Instruction dump:
[    2.174119] 90050004 4e800020 2f840003 419e0014 2f840004 409eff64 6400c000 4bffff5c
[    2.196000] 64001000 7c0004ac 812b0500 0c090000 <4c00012c> 61290200 7c0004ac 912b0500
[    2.218100] ---[ end trace 21659aedb84ad816 ]---
[    2.237089]
[    3.232940] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
[    3.232954]
[    3.271575] Rebooting in 1 seconds..

Check pdata->have_sysif_regs flag before accessing system interface
registers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fatal errors such as a device disconnect must not trigger
error handling. The error returns must be checked.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

del_timer_sync() cannot be used in interrupt.
Replace it with del_timer() and a flag
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.

Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub.  A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.

Right now the driver tests whether the root hub is running, and that
is not the correct test.  In particular, if the controller has died
then the root hub should not be restarted.  In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.

In the end, the test needs to be changed.  Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended.  This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These devices have a number of non serial interfaces as well.  Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.

We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.

| alloc_sglist()
| usbtest_ioctl()

Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.

| test_ctrl_queue()
| usbtest_ioctl()

Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children.  The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:

	The attribute's method calls usb_set_configuration(),
	which calls usb_disable_device() with the bandwidth_mutex
	held.

	usb_disable_device() unregisters the existing interfaces,
	which causes the hub driver to be unbound.

	The hub_disconnect() routine calls hub_quiesce(), which
	calls usb_disconnect() for each of the hub's children.

	usb_disconnect() attempts to acquire the bandwidth_mutex
	around a call to usb_disable_device().

The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it.  Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.

This has the potential to change system behavior slightly when a
config change races with another config or altsetting change.  Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure.  But since we don't try to recover from
config-change failures anyway, this doesn't matter.

[This should be marked for stable kernels that contain the commit
fccf4e86 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

usb: fixes for v3.4-rc cycle

Here are the fixes I have queued for v3.4-rc cycle so far.

It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.

For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.

For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).

For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.

On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.

All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.

Pull ARM fixes from Russell King:
 "Nothing too disasterous, the biggest thing being the removal of the
  regulator support for vcore in the AMBA driver; only one SoC was using
  this and it got broken during the last merge window, which then
  started causing problems for other people.  Mutual agreement was
  reached for it to be removed."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7386/1: jump_label: fixup for rename to static_key
  ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
  ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
  ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
  ARM: 7383/1: nommu: populate vectors page from paging_init
  ARM: 7381/1: nommu: fix typo in mm/Kconfig
  ARM: 7380/1: DT: do not add a zero-sized memory property
  ARM: 7379/1: DT: fix atags_to_fdt() second call site
  ARM: 7366/3: amba: Remove AMBA level regulator support
  ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
  ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented

The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.

We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.

Bug introduced in commit 92ae03f2 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up").  On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.

I had actually tested the corner-cases, I had only tested them on
x86-64.  Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)

This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way.  'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

c5905afb ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key.  Fixup ARM for this to
eliminate these build warnings:

  include/linux/jump_label.h:113:2:
  warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
  include/asm/jump_label.h:17:82:
  note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.

This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.

Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.

This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.

Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 26f41062 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.

First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one).  Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt.  Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.

All of this actually caused resume failures for some devices on Mikko's
system.

To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value.  Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
 - A handful of warning and build fixes for Qualcomm MSM
 - Build/warning and bug fixes for Samsung Exynos
 - A fix from Rob Herring that removes misplaced interrupt-parent
   properties from a few device trees
 - A fix to OMAP dealing with cpufreq build errors, removing some of the
   offending code since it was redundant anyway

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
  ARM: dts: remove blank interrupt-parent properties
  ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
  ARM: EXYNOS: Remove broken config values for touchscren for NURI board
  ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
  ARM: EXYNOS: fix regulator name for NURI board
  ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
  ARM: msm: Fix section mismatches in proc_comm.c
  video: msm: Fix section mismatches in mddi.c
  arm: msm: trout: fix compile failure
  arm: msm: halibut: remove unneeded fixup
  ARM: EXYNOS: Add PDMA and MDMA physical base address defines
  ARM: S5PV210: Fix compiler warning in dma.c file
  ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
  ARM: EXYNOS: Add missing definition for IRQ_I2S0
  ARM: S5PV210: fix unused LDO supply field from wm8994_pdata

Pull another round of sound fixes from Takashi Iwai:
 "A few regression fixes for Realtek HD-audio codecs, mainly specific to
  some laptop models."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
  ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
  ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
  ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
  ALSA: hda/realtek - Add a few ALC882 model strings back

Commit 18a4d0a2 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.

Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
  ARM: EXYNOS: Remove broken config values for touchscren for NURI board
  ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
  ARM: EXYNOS: fix regulator name for NURI board
  ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
  ARM: EXYNOS: Add PDMA and MDMA physical base address defines
  ARM: S5PV210: Fix compiler warning in dma.c file
  ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
  ARM: EXYNOS: Add missing definition for IRQ_I2S0
  ARM: S5PV210: fix unused LDO supply field from wm8994_pdata

Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables.  Remove it.

Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.

Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

These were incorrectly introduced and can cause problems for of_irq_init.

The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

From David Brown:
  "Here are some fixes for msm that fix problems caused by the latest
   ARM code.  The ones from Daniel remove unneeded fixups that now
   cause compilation failures.  Mine fix section mismatches, that were
   incompletely fixed earlier."

* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
  ARM: msm: Fix section mismatches in proc_comm.c
  video: msm: Fix section mismatches in mddi.c
  arm: msm: trout: fix compile failure
  arm: msm: halibut: remove unneeded fixup

Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pull perf tool fixes from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf kvm: Finding struct machine fails for PERF_RECORD_MMAP
  perf annotate: Validate addr in symbol__inc_addr_samples
  perf hists browser: Fix NULL deref in hists browsing code
  perf hists: Catch and handle out-of-date hist entry maps.
  perf annotate: Fix hist decay
  perf top: Add intel_idle to the skip list

GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it.  Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).

So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a71 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pull system.h fixups for less common arch's from Paul Gortmaker:
 "Here is what is hopefully the last of the system.h related fixups.

  The fixes for Alpha and ia64 are code relocations consistent with what
  was done for the more mainstream architectures.  Note that the
  diffstat lines removed vs lines added are not the same since I've
  fixed some of the whitespace issues in the relocated code blocks.
  However they are functionally the same.  Compile tested locally, plus
  these two have been in linux-next for a while.

  There is also a trivial one line system.h related fix for the Tilera
  arch from Chris Metcalf to fix an implict include.."

* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  irq_work: fix compile failure on tile from missing include
  ia64: populate the cmpxchg header with appropriate code
  alpha: fix build failures from system.h dismemberment

Pull fbdev fixes from Florian Tobias Schandinat:
 - a compile fix for au1*fb
 - a fix to make kyrofb usable on x86_64
 - a fix for uvesafb to prevent an oops due to NX-protection

 "The fix for kyrofb is a bit large but it's just replacing "unsigned
  long" by "u32" for 64 bit compatibility."

* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
  video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
  fbdev: fix au1*fb builds
  kyrofb: fix on x86_64

Pull the minimal btrfs branch from Chris Mason:
 "We have a use-after-free in there, along with errors when mount -o
  discard is enabled, and a BUG_ON(we should compile with UP more
  often)."

* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: use commit root when loading free space cache
  Btrfs: fix use-after-free in __btrfs_end_transaction
  Btrfs: check return value of bio_alloc() properly
  Btrfs: remove lock assert from get_restripe_target()
  Btrfs: fix eof while discarding extents
  Btrfs: fix uninit variable in repair_eb_io_failure
  Revert "Btrfs: increase the global block reserve estimates"

Pull block driver bits from Jens Axboe:

 - A series of fixes for mtip32xx.  Most from Asai at Micron, but also
   one from Greg, getting rid of the dependency on PCIE_HOTPLUG.

 - A few bug fixes for xen-blkfront, and blkback.

 - A virtio-blk fix for Vivek, making resize actually work.

 - Two fixes from Stephen, making larger transfers possible on cciss.
   This is needed for tape drive support.

* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
  block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
  mtip32xx: dump tagmap on failure
  mtip32xx: fix handling of commands in various scenarios
  mtip32xx: Shorten macro names
  mtip32xx: misc changes
  mtip32xx: Add new sysfs entry 'status'
  mtip32xx: make setting comp_time as common
  mtip32xx: Add new bitwise flag 'dd_flag'
  mtip32xx: fix error handling in mtip_init()
  virtio-blk: Call revalidate_disk() upon online disk resize
  xen/blkback: Make optional features be really optional.
  xen/blkback: Squash the discard support for 'file' and 'phy' type.
  mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
  cciss: Fix scsi tape io with more than 255 scatter gather elements
  cciss: Initialize scsi host max_sectors for tape drive support
  xen-blkfront: make blkif_io_lock spinlock per-device
  xen/blkfront: don't put bdev right after getting it
  xen-blkfront: use bitmap_set() and bitmap_clear()
  xen/blkback: Enable blkback on HVM guests
  xen/blkback: use grant-table.c hypercall wrappers

Pull block core bits from Jens Axboe:
 "It's a nice and quiet round this time, since most of the tricky stuff
  has been pushed to 3.5 to give it more time to mature.  After a few
  hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
  slow round.

  Really minor stuff in here, the only real functional change is making
  the auto-unplug threshold a per-queue entity.  The threshold is set so
  that it's low enough that we don't hold off IO for too long, but still
  big enough to get a nice benefit from the batched insert (and hence
  queue lock cost reduction).  For raid configurations, this currently
  breaks down."

* 'for-3.4/core' of git://git.kernel.dk/linux-block:
  block: make auto block plug flush threshold per-disk based
  Documentation: Add sysfs ABI change for cfq's target latency.
  block: Make cfq_target_latency tunable through sysfs.
  block: use lockdep_assert_held for queue locking
  block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL

The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.

This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.)  This
patch remedies that.

Apologies to Russell King for breaking his originally working patch.

Also, thanks to Grazvydas Ignotas for reporting the same problem.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sparc fixes from David Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Eliminate obsolete __handle_softirq() function
  sparc64: Fix bootup crash on sun4v.

Pull hwmon patches from Guenter Roeck:
 "Fix build warnings in four drivers"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus_core) Fix compiler warning
  hwmon: (smsc47m1) Fix compiler warning
  hwmon: (acpi_power_meter) Fix compiler warning seen in some configurations
  hwmon: (smsc47b397) Fix compiler warning