the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.

This is a squash commit of:
pinctrl: at91: Remove redundant of_match_ptr
pinctrl: exynos5440: Remove redundant of_match_ptr
pinctrl: imx35: Remove redundant of_match_ptr
pinctrl: imx51: Remove redundant of_match_ptr
pinctrl: imx53: Remove redundant of_match_ptr
pinctrl: imx6dl: Remove redundant of_match_ptr
pinctrl: imx6q: Remove redundant of_match_ptr
pinctrl: samsung: Remove redundant of_match_ptr
pinctrl: vf610: Remove redundant of_match_ptr
pinctrl: imx6sl: Remove redundant of_match_ptr
pinctrl: plgpio: Remove redundant of_match_ptr
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Palmas pinmux and pin configuration support the single pin level
configuration in place of pin group.

Hence it is only require to pin_config_{set|get} and do not require
pin_config_group_{set|get}. As core framework already check for
require APIs availability, it is not require to implement as dummy
for non-require ops and so removing it.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Current code hold port->lock spinlock and then try to grab the lock again
in adi_gpio_set_value(). Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add missing "atmel,at91sam9x5-pinctrl" compatible string to the
documentation.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace at91_mux_get_deglitch with at91_mux_pio3_get_deglitch when using
sam9x5 (pio3) IP.
at91_mux_get_deglitch only test the activation of the "Input Filter" which
may be overloaded by the activation of the "Input Filter Slow Clock" to use
the input filter as a debounce filter instead of a deglitch filter.

Fix at91_mux_pio3_get_debounce to test the activation of the Input Filter
before testing the activation of the debounce filter (Input Filter Slow
Clock depends on Input Filter).

Fix at91_mux_pio3_set_debounce function to avoid disabling the deglitch
filter ("Input Filter") when debounce filter is disabled.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix AT91_PINCTRL_DEBOUNCE_VAL dt macro typo.
Fix at91_pinctrl_mux_ops callback typos.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There are four I2C interfaces on r8a7790, each of them can be connected to
one of the two respective I2C controllers, e.g. interface #0 can be
configured to work with I2C0 or with IIC0. Additionally some of those
interfaces can also use one of several pin sets. Interface #3 is special,
because it can be used in automatic mode for DVFS. It only has one set
of pins available and those pins cannot be used for anything else, they
also lack the GPIO function.

This patch uses the sh-pfc ability to configure pins, not associated with
GPIOs and adds support for I2C3 to the r8a7790 PFC set up.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Adds pinmux for i2c bus 1 and 2. (Pins for 0 and 3 are not multiplexed.)
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

- Remove unused macro MAX_RESOURCES
- Override blackfin legacy peripheral pinmux request and free APIs by
devm_pinctrl_get_select_default() to init the peripheral portmux setting.

v3-chagnes:
- Move pinctrl soc data out of blackfin arch folder.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

sizeof() is already size_t so there is no need to cast here.  Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:

  drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
  drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

- Remove non gpio lib code from blackfin architecture.
- Limit the lagecy blackfin gpio driver to bf5xx processors only.
- Remove unused definition of the pint power functions.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The new ADI GPIO2 controller was introduced since the BF548 and BF60x
processors. It differs a lot from the old one on BF5xx processors. So,
create a pinctrl driver under the pinctrl framework.

- Define gpio ports and pin interrupt controllers as individual platform
  devices.
- Register a pinctrl driver for the whole GPIO ports and pin interrupt
  devices.
- Probe pint devices before port devices. Put device instances into
  the global gpio and pint lists.
- Define peripheral, irq and gpio reservation bit masks for each gpio
  port as runtime resources.
- Save and restore gpio port and pint status MMRs in syscore PM functions.
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
  and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
  in pin controller probe function. Get the pin groups and functions via
  the soc data reference.
- Call gpiochip_add_pin_range() in gpio device probe function to register
  range cross reference between gpio device and pin control device.
- Get range by pinctrl_find_gpio_range_from_pin(), find gpio_port object
  by container_of() and find adi_pinctrl by pin control device name.
- Handle peripheral and gpio requests in pinctrl operation functions.
- Demux gpio IRQs via the irq_domain created by each GPIO port.

v2-changes:
- Remove unlinke() directive.

v3-changes:
- Rename struct adi_pmx to adi_pinctrl.
- Fix the comments of struct gpio_pint.
- Remove unused pin_base in struct gpio_port.
- Change pint_assign into bool type.
- Add comments about the relationship between pint device and port device
to the driver header.
- Use BIT macro to shift bit.
- Remove all bitmap reservation help functions. Inline reservation functions
into the actual code.
- Remove gpio and offset mutual reference help functions.
- Remove all help functions to find gpio_port and adi_pinctrl structs. Get
range by pinctrl_find_gpio_range_from_pin(), find gpio_port object by
container_of() and find adi_pinctrl by pin control device name.
- Pass bool type usage variable to port_setup help function.
- Separate long bit operations into several lines and add comments.
- Use debugfs to output all GPIO request information.
- Avoid to set drvdata to NULL
- Add explanation to function adi_gpio_init_int()
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Remove the reference to pin control device from the gpio_port struct.
Remove the reference list to gpio device from the adi_pinctrl struct.
Replace the global adi_pinctrl list with adi_gpio_port_list. Walk through
the gpio list to do power suspend and resume operations.
- Remove the global GPIO base from struct adi_pinctrl, define pin base in
the platform data for each GPIO port device.
- Initialize adi_pinctrl_setup in arch_initcall().
- print the status of triggers, whether it is in GPIO mode, if it is
flagged to be used as IRQ, etc in adi_pin_dbg_show().
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.

v4-changes:
- remove useless system_state checking.
- replace dev_err with dev_warn in both irq and gpio pin cases.
- comment on relationship between irq type and invert operation.
- It is not necessary to check the reservation mode of the requested
pin in IRQ chip operation. Remove the reservation map.
- Use existing gpio/pinctrl subsystem debugfs files. Remove pinctrl-adi2
driver specific debugfs output.
- Add linkport group and function information for bf60x.
- Separate uart and ctsrts pins into 2 groups.
- Separate APAPI and alternative ATAPI pins into 2 groups.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver cannot be built as a module, so having a MODULE_ALIAS() isn't
useful.

While at it, fix a small typo in the file header comment and make the
module description string consistent with those for earlier Tegra SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull timer code update from Thomas Gleixner:
 - armada SoC clocksource overhaul with a trivial merge conflict
 - Minor improvements to various SoC clocksource drivers

* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
  clocksource: armada-370-xp: Get reference fixed-clock by name
  clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
  clocksource: armada-370-xp: Fix device-tree binding
  clocksource: armada-370-xp: Introduce new compatibles
  clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
  clocksource: armada-370-xp: Simplify TIMER_CTRL register access
  clocksource: armada-370-xp: Use BIT()
  ARM: timer-sp: Set dynamic irq affinity
  ARM: nomadik: add dynamic irq flag to the timer
  clocksource: sh_cmt: 32-bit control register support
  clocksource: em_sti: Convert to devm_* managed helpers

Pull CIFS fixes from Steve French:
 "Two minor cifs fixes and a minor documentation cleanup for cifs.txt"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update cifs.txt and remove some outdated infos
  cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
  cifs: Do not take a reference to the page in cifs_readpage_worker()

Pull UBI fixes from Artem Bityutskiy:
 "Just a single fastmap fix plus a regression fix"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Fix invalidate_fastmap()
  UBI: Fix PEB leak in wear_leveling_worker()

Pull ubifs fix from Artem Bityutskiy:
 "Just one patch which fixes the power-cut recovery testing mode.

  I'll start using a single UBI/UBIFS tree instead of 2 trees from now
  on.  So in the future you'll get 1 small pull request instead of 2
  tiny ones"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: remove invalid warn msg with tst_recovery enabled

Pull MIPS fixes from Ralf Baechle:
 "These are four patches for three construction sites:

   - Fix register decoding for the combination of multi-core processors
     and multi-threading.

   - Two more fixes that are part of the ongoing DECstation resurrection
     work.  One of these touches a DECstation-only network driver.

   - Finally Markos' trivial build fix for the AP/SP support.

  (With this applied now all MIPS defconfigs are building again)"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
  MIPS: Fix SMP core calculations when using MT support.
  MIPS: DECstation I/O ASIC DMA interrupt handling fix
  MIPS: DECstation HRT initialization rearrangement

Pull x86 platform updates from Matthew Garrett:
 "Nothing amazing here, almost entirely cleanups and minor bugfixes and
  one bit of hardware enablement in the amilo-rfkill driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  platform/x86: panasonic-laptop: reuse module_acpi_driver
  samsung-laptop: fix config build error
  platform: x86: remove unnecessary platform_set_drvdata()
  amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
  wmi: parse_wdg() should return kernel error codes
  hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
  platform: replace strict_strto*() with kstrto*()
  x86: irst: use module_acpi_driver to simplify the code
  x86: smartconnect: use module_acpi_driver to simplify the code
  platform samsung-q10: use ACPI instead of direct EC calls
  thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
  thinkpad_acpi: return -NODEV while operating uninitialized LEDs

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
  [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
  [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
  [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
  [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
  [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
  [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
  [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
  [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
  [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
  [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
  [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
  [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
  ...

Pull SLAB update from Pekka Enberg:
 "Nothing terribly exciting here apart from Christoph's kmalloc
  unification patches that brings sl[aou]b implementations closer to
  each other"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slab: Use correct GFP_DMA constant
  slub: remove verify_mem_not_deleted()
  mm/sl[aou]b: Move kmallocXXX functions to common code
  mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
  mm/slub.c: beautify code for removing redundancy 'break' statement.
  slub: Remove unnecessary page NULL check
  slub: don't use cpu partial pages on UP
  mm/slub: beautify code for 80 column limitation and tab alignment
  mm/slub: remove 'per_cpu' which is useless variable

Pull input update from Dmitry Torokhov:
 "The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
  allows safely passing file descriptors to input devices to session
  processes and later being able to stop delivery of events through
  these fds so that inactive sessions will no longer receive user input
  that does not belong to them"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - add EVIOCREVOKE ioctl

Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow.  Let's just fix
it.
Reported-by: Sedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Matt found that commit 27a7c642 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot.  The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA.  While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].

Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF.  No tool in its right mind would set it to any value
other than these.

[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPTReported-and-tested-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull writeback fix from Wu Fengguang:
 "A trivial writeback fix"

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Do not sort b_io list only because of block device inode

The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.

This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.

The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry.  We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Björn JACKE <bj@sernet.de>
Signed-off-by: Steve French <smfrench@gmail.com>

When reading a single page with cifs_readpage(), we make a call to
fscache_read_or_alloc_page() which once done, asynchronously calls
the completion function cifs_readpage_from_fscache_complete(). This
completion function unlocks the page once it has been populated from
cache. The module then attempts to unlock the page a second time in
cifs_readpage() which leads to warning messages.

In case of a successful call to fscache_read_or_alloc_page() we should skip
the second unlock_page() since this will be called by the
cifs_readpage_from_fscache_complete() once the page has been populated by
fscache.

With the modifications to cifs_readpage_worker(), we will need to re-grab the
page lock in cifs_write_begin().

The problem was first noticed when testing new fscache patches for cifs.
https://bugzilla.redhat.com/show_bug.cgi?id=1005737Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

We do not need to take a reference to the pagecache in
cifs_readpage_worker() since the calling function will have already
taken one before passing the pointer to the page as an argument to the
function.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

Pull hwmon fixes from Guenter Roeck:
 "Some more low risk cleanup patches:

   - Remove unnecessary pci_set_drvdata in k10temp driver from Jingoo Han
   - Fix return values in several drivers from Sachin Kamat
   - Remove redundant break in amc6821 driver from Sachin Kamat"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) remove unnecessary pci_set_drvdata()
  hwmon: (tmp421) Fix return value
  hwmon: (amc6821) Remove redundant break
  hwmon: (amc6821) Fix return value
  hwmon: (ibmaem) Fix return value
  hwmon: (emc2103) Fix return value

Pull Xtensa updates from Chris Zankel.

* tag 'xtensa-next-20130912' of git://github.com/czankel/xtensa-linux:
  xtensa: Fix broken allmodconfig build
  xtensa: remove CCOUNT_PER_JIFFY
  xtensa: fix !CONFIG_XTENSA_CALIBRATE_CCOUNT build failure
  xtensa: don't use echo -e needlessly
  xtensa: new fast_alloca handler
  xtensa: keep a3 and excsave1 on entry to exception handlers
  xtensa: enable kernel preemption
  xtensa: check thread flags atomically on return from user exception