ARM: OMAP: SmartReflex: Move smartreflex driver to drivers/

After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.

The build is controlled by the following Kconfig options:
 . CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
 . CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
   support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
 . CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

arch/arm/mach-omap2/Makefile

@@ -70,8 +70,8 @@ obj-$(CONFIG_ARCH_OMAP4)		+= pm44xx.o omap-mpuss-lowpower.o \
 					   cpuidle44xx.o
 obj-$(CONFIG_PM_DEBUG)			+= pm-debug.o
 
-obj-$(CONFIG_POWER_AVS_OMAP)		+= sr_device.o smartreflex.o
-obj-$(CONFIG_POWER_AVS_OMAP_CLASS3)	+= smartreflex-class3.o
+obj-$(CONFIG_POWER_AVS_OMAP)		+= sr_device.o
+obj-$(CONFIG_POWER_AVS_OMAP_CLASS3)    += smartreflex-class3.o
 
 AFLAGS_sleep24xx.o			:=-Wa,-march=armv6
 AFLAGS_sleep34xx.o			:=-Wa,-march=armv7-a$(plus_sec)

arch/arm/plat-omap/Kconfig

@@ -45,26 +45,12 @@ config OMAP_DEBUG_LEDS
 	depends on OMAP_DEBUG_DEVICES
 	default y if LEDS_CLASS
 
-menuconfig POWER_AVS
-	tristate "Adaptive Voltage Scaling class support"
-	help
-	  AVS(Adaptive Voltage Scaling) is a power management technique which
-	  finely controls the operating voltage of a device in order to optimize
-	   (i.e. reduce) its power consumption.
-	  At a given operating point the voltage is adapted depending on
-	  static factors (chip manufacturing process) and dynamic factors
-	  (temperature depending performance).
-	  AVS is also called SmartReflex on OMAP devices.
-
-	  Say Y here to enable Adaptive Voltage Scaling class support.
-
-if POWER_AVS
-
 config POWER_AVS_OMAP
 	bool "AVS(Adaptive Voltage Scaling) support for OMAP IP versions 1&2"
-	depends on (ARCH_OMAP3 || ARCH_OMAP4) && PM
+	depends on POWER_AVS && (ARCH_OMAP3 || ARCH_OMAP4) && PM
 	help
-	  Say Y to enable AVS support on OMAP containing the version 1 or
+	  Say Y to enable AVS(Adaptive Voltage Scaling)
+	  support on OMAP containing the version 1 or
 	  version 2 of the SmartReflex IP.
 	  V1 is the 65nm version used in OMAP3430.
 	  V2 is the update for the 45nm version of the IP used in OMAP3630
@@ -89,8 +75,6 @@ config POWER_AVS_OMAP_CLASS3
 	  Class 3 implementation of Smartreflex employs continuous hardware
 	  voltage calibration.
 
-endif # POWER_AVS
-
 config OMAP_RESET_CLOCKS
 	bool "Reset unused clocks during boot"
 	depends on ARCH_OMAP

drivers/power/Kconfig

@@ -308,3 +308,5 @@ config AB8500_BATTERY_THERM_ON_BATCTRL
 	  Say Y to enable battery temperature measurements using
 	  thermistor connected on BATCTRL ADC.
 endif # POWER_SUPPLY
+
+source "drivers/power/avs/Kconfig"

drivers/power/Makefile

@@ -43,4 +43,5 @@ obj-$(CONFIG_CHARGER_GPIO)	+= gpio-charger.o
 obj-$(CONFIG_CHARGER_MANAGER)	+= charger-manager.o
 obj-$(CONFIG_CHARGER_MAX8997)	+= max8997_charger.o
 obj-$(CONFIG_CHARGER_MAX8998)	+= max8998_charger.o
+obj-$(CONFIG_POWER_AVS)		+= avs/
 obj-$(CONFIG_CHARGER_SMB347)	+= smb347-charger.o

drivers/power/avs/Kconfig

+menuconfig POWER_AVS
+	tristate "Adaptive Voltage Scaling class support"
+	help
+	  AVS is a power management technique which finely controls the
+	  operating voltage of a device in order to optimize (i.e. reduce)
+	  its power consumption.
+	  At a given operating point the voltage is adapted depending on
+	  static factors (chip manufacturing process) and dynamic factors
+	  (temperature depending performance).
+	  AVS is also called SmartReflex on OMAP devices.
+
+	  Say Y here to enable Adaptive Voltage Scaling class support.

drivers/power/avs/Makefile

+obj-$(CONFIG_POWER_AVS_OMAP)		+= smartreflex.o

arch/arm/mach-omap2/smartreflex.c → drivers/power/avs/smartreflex.c

@@ -3,7 +3,7 @@
  *
  * Author: Thara Gopinath	<thara@ti.com>
  *
- * Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright (C) 2012 Texas Instruments, Inc.
  * Thara Gopinath <thara@ti.com>
  *
  * Copyright (C) 2008 Nokia Corporation
@@ -27,9 +27,6 @@
 #include <linux/pm_runtime.h>
 #include <linux/power/smartreflex.h>
 
-#include "common.h"
-#include "pm.h"
-
 #define SMARTREFLEX_NAME_LEN	16
 #define NVALUE_NAME_LEN		40
 #define SR_DISABLE_TIMEOUT	200