Commit 389cfd96 authored by Randy Dunlap's avatar Randy Dunlap Committed by Jonathan Corbet

docs/admin: alphabetize parts of kernel-parameters.txt (part 2)

Alphabetize several of the kernel boot parameters in
kernel-parameters.txt.
Signed-off-by: default avatarRandy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: default avatarJonathan Corbet <corbet@lwn.net>
parent d2fc83c1
......@@ -461,6 +461,12 @@
Format: <io>,<irq>,<mode>
See header of drivers/net/hamradio/baycom_ser_hdx.c.
bert_disable [ACPI]
Disable BERT OS support on buggy BIOSes.
bgrt_disable [ACPI][X86]
Disable BGRT to avoid flickering OEM logo.
blkdevparts= Manual partition parsing of block device(s) for
embedded devices based on command line input.
See Documentation/block/cmdline-partition.rst
......@@ -476,12 +482,6 @@
See Documentation/admin-guide/bootconfig.rst
bert_disable [ACPI]
Disable BERT OS support on buggy BIOSes.
bgrt_disable [ACPI][X86]
Disable BGRT to avoid flickering OEM logo.
bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
bttv.radio= Most important insmod options are available as
kernel args too.
......@@ -766,6 +766,24 @@
0: default value, disable debugging
1: enable debugging at boot time
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
cpu0_hotplug [X86] Turn on CPU0 hotplug feature when
CONFIG_BOOTPARAM_HOTPLUG_CPU0 is off.
Some features depend on CPU0. Known dependencies are:
1. Resume from suspend/hibernate depends on CPU0.
Suspend/hibernate will fail if CPU0 is offline and you
need to online CPU0 before suspend/hibernate.
2. PIC interrupts also depend on CPU0. CPU0 can't be
removed if a PIC interrupt is detected.
It's said poweroff/reboot may depend on CPU0 on some
machines although I haven't seen such issues so far
after CPU0 is offline on a few tested machines.
If the dependencies are under your control, you can
turn on cpu0_hotplug.
cpuidle.off=1 [CPU_IDLE]
disable the cpuidle sub-system
......@@ -786,9 +804,13 @@
on every CPU online, such as boot, and resume from suspend.
Default: 10000
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
crash_kexec_post_notifiers
Run kdump after running panic-notifiers and dumping
kmsg. This only for the users who doubt kdump always
succeeds in any situation.
Note that this also increases risks of kdump failure,
because some panic notifiers can make the crashed
kernel more unstable.
crashkernel=size[KMG][@offset[KMG]]
[KNL] Using kexec, Linux can switch to a 'crash kernel'
......@@ -1640,16 +1662,6 @@
hpet_mmap= [X86, HPET_MMAP] Allow userspace to mmap HPET
registers. Default set by CONFIG_HPET_MMAP_DEFAULT.
hugetlb_cma= [HW,CMA] The size of a CMA area used for allocation
of gigantic hugepages. Or using node format, the size
of a CMA area per node can be specified.
Format: nn[KMGTPE] or (node format)
<node>:nn[KMGTPE][,<node>:nn[KMGTPE]]
Reserve a CMA area of given size and allocate gigantic
hugepages using the CMA allocator. If enabled, the
boot-time allocation of gigantic hugepages is skipped.
hugepages= [HW] Number of HugeTLB pages to allocate at boot.
If this follows hugepagesz (below), it specifies
the number of pages of hugepagesz to be allocated.
......@@ -1671,6 +1683,16 @@
Documentation/admin-guide/mm/hugetlbpage.rst.
Format: size[KMG]
hugetlb_cma= [HW,CMA] The size of a CMA area used for allocation
of gigantic hugepages. Or using node format, the size
of a CMA area per node can be specified.
Format: nn[KMGTPE] or (node format)
<node>:nn[KMGTPE][,<node>:nn[KMGTPE]]
Reserve a CMA area of given size and allocate gigantic
hugepages using the CMA allocator. If enabled, the
boot-time allocation of gigantic hugepages is skipped.
hugetlb_free_vmemmap=
[KNL] Reguires CONFIG_HUGETLB_PAGE_FREE_VMEMMAP
enabled.
......@@ -2683,8 +2705,6 @@
If there are multiple matching configurations changing
the same attribute, the last one is used.
memblock=debug [KNL] Enable memblock debug messages.
load_ramdisk= [RAM] [Deprecated]
lockd.nlm_grace_period=P [NFS] Assign grace period.
......@@ -2926,6 +2946,8 @@
mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
memory.
memblock=debug [KNL] Enable memblock debug messages.
memchunk=nn[KMG]
[KNL,SH] Allow user to override the default size for
per-device physically contiguous DMA buffers.
......@@ -3193,10 +3215,6 @@
mtdparts= [MTD]
See drivers/mtd/parsers/cmdlinepart.c
multitce=off [PPC] This parameter disables the use of the pSeries
firmware feature for updating multiple TCE entries
at a time.
mtdset= [ARM]
ARM/S3C2412 JIVE boot control
......@@ -3223,6 +3241,10 @@
Used for mtrr cleanup. It is spare mtrr entries number.
Set to 2 or more if your graphical card needs more.
multitce=off [PPC] This parameter disables the use of the pSeries
firmware feature for updating multiple TCE entries
at a time.
n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
netdev= [NET] Network devices parameters
......@@ -3232,6 +3254,11 @@
This usage is only documented in each driver source
file if at all.
netpoll.carrier_timeout=
[NET] Specifies amount of time (in seconds) that
netpoll should wait for a carrier. By default netpoll
waits 4 seconds.
nf_conntrack.acct=
[NETFILTER] Enable connection tracking flow accounting
0 to disable accounting
......@@ -3382,11 +3409,6 @@
These settings can be accessed at runtime via
the nmi_watchdog and hardlockup_panic sysctls.
netpoll.carrier_timeout=
[NET] Specifies amount of time (in seconds) that
netpoll should wait for a carrier. By default netpoll
waits 4 seconds.
no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
emulation library even if a 387 maths coprocessor
is present.
......@@ -3678,20 +3700,6 @@
nox2apic [X86-64,APIC] Do not enable x2APIC mode.
cpu0_hotplug [X86] Turn on CPU0 hotplug feature when
CONFIG_BOOTPARAM_HOTPLUG_CPU0 is off.
Some features depend on CPU0. Known dependencies are:
1. Resume from suspend/hibernate depends on CPU0.
Suspend/hibernate will fail if CPU0 is offline and you
need to online CPU0 before suspend/hibernate.
2. PIC interrupts also depend on CPU0. CPU0 can't be
removed if a PIC interrupt is detected.
It's said poweroff/reboot may depend on CPU0 on some
machines although I haven't seen such issues so far
after CPU0 is offline on a few tested machines.
If the dependencies are under your control, you can
turn on cpu0_hotplug.
nps_mtm_hs_ctr= [KNL,ARC]
This parameter sets the maximum duration, in
cycles, each HW thread of the CTOP can run
......@@ -3824,14 +3832,6 @@
panic_on_warn panic() instead of WARN(). Useful to cause kdump
on a WARN().
crash_kexec_post_notifiers
Run kdump after running panic-notifiers and dumping
kmsg. This only for the users who doubt kdump always
succeeds in any situation.
Note that this also increases risks of kdump failure,
because some panic notifiers can make the crashed
kernel more unstable.
parkbd.port= [HW] Parallel port number the keyboard adapter is
connected to, default is 0.
Format: <parport#>
......@@ -5877,6 +5877,37 @@
This will guarantee that all the other pcrs
are saved.
tp_printk [FTRACE]
Have the tracepoints sent to printk as well as the
tracing ring buffer. This is useful for early boot up
where the system hangs or reboots and does not give the
option for reading the tracing buffer or performing a
ftrace_dump_on_oops.
To turn off having tracepoints sent to printk,
echo 0 > /proc/sys/kernel/tracepoint_printk
Note, echoing 1 into this file without the
tracepoint_printk kernel cmdline option has no effect.
The tp_printk_stop_on_boot (see below) can also be used
to stop the printing of events to console at
late_initcall_sync.
** CAUTION **
Having tracepoints sent to printk() and activating high
frequency tracepoints such as irq or sched, can cause
the system to live lock.
tp_printk_stop_on_boot [FTRACE]
When tp_printk (above) is set, it can cause a lot of noise
on the console. It may be useful to only include the
printing of events during boot up, as user space may
make the system inoperable.
This command line option will stop the printing of events
to console at the late_initcall_sync() time frame.
trace_buf_size=nn[KMG]
[FTRACE] will set tracing buffer size on each cpu.
......@@ -5924,37 +5955,6 @@
See also Documentation/trace/ftrace.rst "trace options"
section.
tp_printk [FTRACE]
Have the tracepoints sent to printk as well as the
tracing ring buffer. This is useful for early boot up
where the system hangs or reboots and does not give the
option for reading the tracing buffer or performing a
ftrace_dump_on_oops.
To turn off having tracepoints sent to printk,
echo 0 > /proc/sys/kernel/tracepoint_printk
Note, echoing 1 into this file without the
tracepoint_printk kernel cmdline option has no effect.
The tp_printk_stop_on_boot (see below) can also be used
to stop the printing of events to console at
late_initcall_sync.
** CAUTION **
Having tracepoints sent to printk() and activating high
frequency tracepoints such as irq or sched, can cause
the system to live lock.
tp_printk_stop_on_boot [FTRACE]
When tp_printk (above) is set, it can cause a lot of noise
on the console. It may be useful to only include the
printing of events during boot up, as user space may
make the system inoperable.
This command line option will stop the printing of events
to console at the late_initcall_sync() time frame.
traceoff_on_warning
[FTRACE] enable this option to disable tracing when a
warning is hit. This turns off "tracing_on". Tracing can
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment