Merge tag 'sunxi-dt-for-4.5-2' of...

Merge tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Allwinner DT patches, round 2

Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.

* tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sun5i: Add dts file for the Empire Electronix D709 tablet
  ARM: dts: sun7i: Enable gmac on Wits Pro A20 DKT
  ARM: dt: sun7i: Enable audio codec on MK808C
  ARM: sunxi: dt: enable audio codec on mk802
  ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet
  ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
  ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
  ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
  ARM: dts: sun4i: gemei-g9: Enable PA GPIO pin configuration
  ARM: dts: sun4i: Enable onboard codec used on the pov protab2-ips9 tablet
  ARM: dts: sun5i: Enable onboard codec used on the UTOO P66 tablet
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -638,6 +638,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a10s-olinuxino-micro.dtb \
 	sun5i-a10s-r7-tv-dongle.dtb \
 	sun5i-a10s-wobo-i5.dtb \
+	sun5i-a13-empire-electronix-d709.dtb \
 	sun5i-a13-hsg-h702.dtb \
 	sun5i-a13-inet-98v-rev2.dtb \
 	sun5i-a13-olinuxino.dtb \

arch/arm/boot/dts/sun4i-a10-gemei-g9.dts

@@ -65,13 +65,16 @@ chosen {
 /*
  * TODO:
  *   2x cameras via CSI
- *   audio input
  *   AXP battery management
  *   NAND
  *   OTG
  *   Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48
  */
 &codec {
+	/* PH15 controls power to external amplifier (ft2012q) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -151,6 +154,15 @@ &mmc0 {
 	status = "okay";
 };
 
+&pio {
+	codec_pa_pin: codec_pa_pin@0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

arch/arm/boot/dts/sun4i-a10-mk802.dts

@@ -58,6 +58,10 @@ chosen {
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts

@@ -72,6 +72,13 @@ chosen {
 	};
 };
 
+&codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
@@ -163,6 +170,13 @@ bl_en_pin_protab: bl_en_pin@0 {
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
+	codec_pa_pin: codec_pa_pin@0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	touchscreen_pins: touchscreen_pins@0 {
 		allwinner,pins = "PA5", "PB13";
 		allwinner,function = "gpio_out";

arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts

+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Empire Electronix D709 tablet";
+	compatible = "empire-electronix,d709", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button@200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button@400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+
+	mmccard: mmccard@0 {
+		reg = <0>;
+		compatible = "mmc-card";
+		broken-hpi;
+	};
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 {
+		allwinner,pins = "PG0";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+		allwinner,pins = "PG1";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin@0 {
+		allwinner,pins = "PG2";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-int-pll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_usb0_vbus {
+	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_b>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb0_vbus_pin_a {
+	allwinner,pins = "PG12";
+};
+
+&usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_ldo3>;
+	status = "okay";
+};

arch/arm/boot/dts/sun5i-a13-utoo-p66.dts

@@ -73,6 +73,13 @@ i2c_lcd: i2c@0 {
 	};
 };
 
+&codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
@@ -168,6 +175,13 @@ &otg_sram {
 };
 
 &pio {
+	codec_pa_pin: codec_pa_pin@0 {
+		allwinner,pins = "PG3";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	mmc0_cd_pin_p66: mmc0_cd_pin@0 {
 		allwinner,pins = "PG0";
 		allwinner,function = "gpio_in";

arch/arm/boot/dts/sun7i-a20-mk808c.dts

@@ -68,6 +68,10 @@ chosen {
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts

@@ -48,6 +48,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Wexler TAB7200";
@@ -57,12 +58,25 @@ aliases {
 		serial0 = &uart0;
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_enable_pin>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 };
 
 &codec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&codec_pa_pin>;
+	allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
 	status = "okay";
 };
 
@@ -102,6 +116,18 @@ &i2c2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	gt911: touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_reset_pin>;
+		irq-gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* INT (PH21) */
+		reset-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* RST (PB13) */
+		touchscreen-swapped-x-y;
+	};
 };
 
 &lradc {
@@ -146,6 +172,27 @@ &otg_sram {
 };
 
 &pio {
+	bl_enable_pin: bl_enable_pin@0 {
+		allwinner,pins = "PH7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	codec_pa_pin: codec_pa_pin@0 {
+		allwinner,pins = "PH15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	ts_reset_pin: ts_reset_pin@0 {
+		allwinner,pins = "PB13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";
@@ -154,6 +201,12 @@ usb0_id_detect_pin: usb0_id_detect_pin@0 {
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts

@@ -80,6 +80,18 @@ &ehci1 {
 	status = "okay";
 };
 
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_rgmii_a>;
+	phy = <&phy1>;
+	phy-mode = "rgmii";
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;