Merge branches 'spear/clock' and 'imx/clock' into next/clock

Updated to resolve dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/arm/SPEAr/overview.txt

@@ -17,14 +17,14 @@ Introduction
   SPEAr (Platform)
 	- SPEAr3XX (3XX SOC series, based on ARM9)
 		- SPEAr300 (SOC)
-			- SPEAr300_EVB (Evaluation Board)
+			- SPEAr300 Evaluation Board
 		- SPEAr310 (SOC)
-			- SPEAr310_EVB (Evaluation Board)
+			- SPEAr310 Evaluation Board
 		- SPEAr320 (SOC)
-			- SPEAr320_EVB (Evaluation Board)
+			- SPEAr320 Evaluation Board
 	- SPEAr6XX (6XX SOC series, based on ARM9)
 		- SPEAr600 (SOC)
-			- SPEAr600_EVB (Evaluation Board)
+			- SPEAr600 Evaluation Board
 	- SPEAr13XX (13XX SOC series, based on ARM CORTEXA9)
 		- SPEAr1300 (SOC)
 
@@ -51,10 +51,11 @@ Introduction
   Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for
   spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine
   specific files, like spear300.c, spear310.c, spear320.c and spear600.c.
-  mach-spear* also contains board specific files for each machine type.
+  mach-spear* doesn't contains board specific files as they fully support
+  Flattened Device Tree.
 
 
   Document Author
   ---------------
 
-  Viresh Kumar, (c) 2010 ST Microelectronics
+  Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics

Documentation/devicetree/bindings/arm/spear-timer.txt

+* SPEAr ARM Timer
+
+** Timer node required properties:
+
+- compatible : Should be:
+	"st,spear-timer"
+- reg: Address range of the timer registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupt: Should contain the timer interrupt number
+
+Example:
+
+	timer@f0000000 {
+		compatible = "st,spear-timer";
+		reg = <0xf0000000 0x400>;
+		interrupts = <2>;
+	};

Documentation/devicetree/bindings/arm/spear.txt

@@ -6,3 +6,21 @@ Boards with the ST SPEAr600 SoC shall have the following properties:
 Required root node property:
 
 compatible = "st,spear600";
+
+Boards with the ST SPEAr300 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear300";
+
+Boards with the ST SPEAr310 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear310";
+
+Boards with the ST SPEAr320 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear320";

Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt

+* Freescale IOMUX Controller (IOMUXC) for i.MX
+
+The IOMUX Controller (IOMUXC), together with the IOMUX, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are up to
+8 muxing options (called ALT modes). Since different modules require
+different PAD settings (like pull up, keeper, etc) the IOMUXC controls
+also the PAD settings parameters.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Freescale IMX pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and config
+of the pins in that group. The 'mux' selects the function mode(also named mux
+mode) this pin can work on and the 'config' configures various pad settings
+such as pull-up, open drain, drive strength, etc.
+
+Required properties for iomux controller:
+- compatible: "fsl,<soc>-iomuxc"
+  Please refer to each fsl,<soc>-pinctrl.txt binding doc for supported SoCs.
+
+Required properties for pin configuration node:
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up on this pin. Please refer to fsl,<soc>-pinctrl.txt for the valid
+  pins and functions of each SoC.
+
+Bits used for CONFIG:
+NO_PAD_CTL(1 << 31): indicate this pin does not need config.
+
+SION(1 << 30): Software Input On Field.
+Force the selected mux mode input path no matter of MUX_MODE functionality.
+By default the input path is determined by functionality of the selected
+mux mode (regular).
+
+Other bits are used for PAD setting.
+Please refer to each fsl,<soc>-pinctrl,txt binding doc for SoC specific part
+of bits definitions.
+
+NOTE:
+Some requirements for using fsl,imx-pinctrl binding:
+1. We have pin function node defined under iomux controller node to represent
+   what pinmux functions this SoC supports.
+2. The pin configuration node intends to work on a specific function should
+   to be defined under that specific function node.
+   The function node's name should represent well about what function
+   this group of pins in this pin configuration node are working on.
+3. The driver can use the function node's name and pin configuration node's
+   name describe the pin function and group hierarchy.
+   For example, Linux IMX pinctrl driver takes the function node's name
+   as the function name and pin configuration node's name as group name to
+   create the map table.
+4. Each pin configuration node should have a phandle, devices can set pins
+   configurations by referring to the phandle of that pin configuration node.
+
+Examples:
+usdhc@0219c000 { /* uSDHC4 */
+	fsl,card-wired;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4_1>;
+};
+
+iomuxc@020e0000 {
+	compatible = "fsl,imx6q-iomuxc";
+	reg = <0x020e0000 0x4000>;
+
+	/* shared pinctrl settings */
+	usdhc4 {
+		pinctrl_usdhc4_1: usdhc4grp-1 {
+			fsl,pins = <1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
+				    1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
+				    1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
+				    1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
+				    1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
+				    1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
+				    1493 0x17059	/* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
+				    1501 0x17059	/* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
+				    1509 0x17059	/* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
+				    1517 0x17059>;	/* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
+		};
+	};
+	....
+};
+Refer to the IOMUXC controller chapter in imx6q datasheet,
+0x17059 means enable hysteresis, 47KOhm Pull Up, 50Mhz speed,
+80Ohm driver strength and Fast Slew Rate.
+User should refer to each SoC spec to set the correct value.
+
+TODO: when dtc macro support is available, we can change above raw data
+to dt macro which can get better readability in dts file.

Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt

+NVIDIA Tegra20 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra20-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the tri-state, mux, pull-up/down, and pad control register sets.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+  pin or group. Valid values for function names are listed below. See the Tegra
+  TRM to determine which are valid for each pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    0: no, 1: yes.
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    0: no, 1: yes.
+- nvidia,low-power-mode: Integer. Valid values 0-3. 0 is least power, 3 is
+    most power. Controls the drive power or current. See "Low Power Mode"
+    or "LPMD1" and "LPMD0" in the Tegra TRM.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the Tegra TRM and various pinmux spreadsheets for complete
+details regarding which groups support which functionality. The Linux pinctrl
+driver may also be a useful reference, since it consolidates, disambiguates,
+and corrects data from all those sources.
+
+Valid values for pin and group names are:
+
+  mux groups:
+
+    These all support nvidia,function, nvidia,tristate, and many support
+    nvidia,pull.
+
+    ata, atb, atc, atd, ate, cdev1, cdev2, crtp, csus, dap1, dap2, dap3, dap4,
+    ddc, dta, dtb, dtc, dtd, dte, dtf, gma, gmb, gmc, gmd, gme, gpu, gpu7,
+    gpv, hdint, i2cp, irrx, irtx, kbca, kbcb, kbcc, kbcd, kbce, kbcf, lcsn,
+    ld0, ld1, ld2, ld3, ld4, ld5, ld6, ld7, ld8, ld9, ld10, ld11, ld12, ld13,
+    ld14, ld15, ld16, ld17, ldc, ldi, lhp0, lhp1, lhp2, lhs, lm0, lm1, lpp,
+    lpw0, lpw1, lpw2, lsc0, lsc1, lsck, lsda, lsdi, lspi, lvp0, lvp1, lvs,
+    owc, pmc, pta, rm, sdb, sdc, sdd, sdio1, slxa, slxc, slxd, slxk, spdi,
+    spdo, spia, spib, spic, spid, spie, spif, spig, spih, uaa, uab, uac, uad,
+    uca, ucb, uda.
+
+  tristate groups:
+
+    These only support nvidia,pull.
+
+    ck32, ddrc, pmca, pmcb, pmcc, pmcd, pmce, xm2c, xm2d, ls, lc, ld17_0,
+    ld19_18, ld21_20, ld23_22.
+
+  drive groups:
+
+    With some exceptions, these support nvidia,high-speed-mode,
+    nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
+    nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling.
+
+    drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
+    drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,
+    drive_lcd1, drive_lcd2, drive_sdmmc2, drive_sdmmc3, drive_spi, drive_uaa,
+    drive_uab, drive_uart2, drive_uart3, drive_vi1, drive_vi2, drive_xm2a,
+    drive_xm2c, drive_xm2d, drive_xm2clk, drive_sdio1, drive_crt, drive_ddc,
+    drive_gma, drive_gmb, drive_gmc, drive_gmd, drive_gme, drive_owr,
+    drive_uda.
+
+Example:
+
+	pinctrl@70000000 {
+		compatible = "nvidia,tegra20-pinmux";
+		reg = < 0x70000014 0x10    /* Tri-state registers */
+			0x70000080 0x20    /* Mux registers */
+			0x700000a0 0x14    /* Pull-up/down registers */
+			0x70000868 0xa8 >; /* Pad control registers */
+	};
+
+Example board file extract:
+
+	pinctrl@70000000 {
+		sdio4_default: sdio4_default {
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@c8000600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdio4_default>;
+	};

Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt

+NVIDIA Tegra30 pinmux controller
+
+The Tegra30 pinctrl binding is very similar to the Tegra20 pinctrl binding,
+as described in nvidia,tegra20-pinmux.txt. In fact, this document assumes
+that binding as a baseline, and only documents the differences between the
+two bindings.
+
+Required properties:
+- compatible: "nvidia,tegra30-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the pad control and mux registers.
+
+Tegra30 adds the following optional properties for pin configuration subnodes:
+- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes.
+- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset. 0: no, 1: yes.
+- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes.
+
+As with Tegra20, see the Tegra TRM for complete details regarding which groups
+support which functionality.
+
+Valid values for pin and group names are:
+
+  per-pin mux groups:
+
+    These all support nvidia,function, nvidia,tristate, nvidia,pull,
+    nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain,
+    nvidia,io-reset.
+
+    clk_32k_out_pa0, uart3_cts_n_pa1, dap2_fs_pa2, dap2_sclk_pa3,
+    dap2_din_pa4, dap2_dout_pa5, sdmmc3_clk_pa6, sdmmc3_cmd_pa7, gmi_a17_pb0,
+    gmi_a18_pb1, lcd_pwr0_pb2, lcd_pclk_pb3, sdmmc3_dat3_pb4, sdmmc3_dat2_pb5,
+    sdmmc3_dat1_pb6, sdmmc3_dat0_pb7, uart3_rts_n_pc0, lcd_pwr1_pc1,
+    uart2_txd_pc2, uart2_rxd_pc3, gen1_i2c_scl_pc4, gen1_i2c_sda_pc5,
+    lcd_pwr2_pc6, gmi_wp_n_pc7, sdmmc3_dat5_pd0, sdmmc3_dat4_pd1, lcd_dc1_pd2,
+    sdmmc3_dat6_pd3, sdmmc3_dat7_pd4, vi_d1_pd5, vi_vsync_pd6, vi_hsync_pd7,
+    lcd_d0_pe0, lcd_d1_pe1, lcd_d2_pe2, lcd_d3_pe3, lcd_d4_pe4, lcd_d5_pe5,
+    lcd_d6_pe6, lcd_d7_pe7, lcd_d8_pf0, lcd_d9_pf1, lcd_d10_pf2, lcd_d11_pf3,
+    lcd_d12_pf4, lcd_d13_pf5, lcd_d14_pf6, lcd_d15_pf7, gmi_ad0_pg0,
+    gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5,
+    gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2,
+    gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7,
+    gmi_wr_n_pi0, gmi_oe_n_pi1, gmi_dqs_pi2, gmi_cs6_n_pi3, gmi_rst_n_pi4,
+    gmi_iordy_pi5, gmi_cs7_n_pi6, gmi_wait_pi7, gmi_cs0_n_pj0, lcd_de_pj1,
+    gmi_cs1_n_pj2, lcd_hsync_pj3, lcd_vsync_pj4, uart2_cts_n_pj5,
+    uart2_rts_n_pj6, gmi_a16_pj7, gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs4_n_pk2,
+    gmi_cs2_n_pk3, gmi_cs3_n_pk4, spdif_out_pk5, spdif_in_pk6, gmi_a19_pk7,
+    vi_d2_pl0, vi_d3_pl1, vi_d4_pl2, vi_d5_pl3, vi_d6_pl4, vi_d7_pl5,
+    vi_d8_pl6, vi_d9_pl7, lcd_d16_pm0, lcd_d17_pm1, lcd_d18_pm2, lcd_d19_pm3,
+    lcd_d20_pm4, lcd_d21_pm5, lcd_d22_pm6, lcd_d23_pm7, dap1_fs_pn0,
+    dap1_din_pn1, dap1_dout_pn2, dap1_sclk_pn3, lcd_cs0_n_pn4, lcd_sdout_pn5,
+    lcd_dc0_pn6, hdmi_int_pn7, ulpi_data7_po0, ulpi_data0_po1, ulpi_data1_po2,
+    ulpi_data2_po3, ulpi_data3_po4, ulpi_data4_po5, ulpi_data5_po6,
+    ulpi_data6_po7, dap3_fs_pp0, dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3,
+    dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7, kb_col0_pq0,
+    kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5,
+    kb_col6_pq6, kb_col7_pq7, kb_row0_pr0, kb_row1_pr1, kb_row2_pr2,
+    kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, kb_row7_pr7,
+    kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_row11_ps3, kb_row12_ps4,
+    kb_row13_ps5, kb_row14_ps6, kb_row15_ps7, vi_pclk_pt0, vi_mclk_pt1,
+    vi_d10_pt2, vi_d11_pt3, vi_d0_pt4, gen2_i2c_scl_pt5, gen2_i2c_sda_pt6,
+    sdmmc4_cmd_pt7, pu0, pu1, pu2, pu3, pu4, pu5, pu6, jtag_rtck_pu7, pv0,
+    pv1, pv2, pv3, ddc_scl_pv4, ddc_sda_pv5, crt_hsync_pv6, crt_vsync_pv7,
+    lcd_cs1_n_pw0, lcd_m1_pw1, spi2_cs1_n_pw2, spi2_cs2_n_pw3, clk1_out_pw4,
+    clk2_out_pw5, uart3_txd_pw6, uart3_rxd_pw7, spi2_mosi_px0, spi2_miso_px1,
+    spi2_sck_px2, spi2_cs0_n_px3, spi1_mosi_px4, spi1_sck_px5, spi1_cs0_n_px6,
+    spi1_miso_px7, ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3,
+    sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, sdmmc1_dat0_py7,
+    sdmmc1_clk_pz0, sdmmc1_cmd_pz1, lcd_sdin_pz2, lcd_wr_n_pz3, lcd_sck_pz4,
+    sys_clk_req_pz5, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, sdmmc4_dat0_paa0,
+    sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4,
+    sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, pbb0,
+    cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, pbb7,
+    cam_mclk_pcc0, pcc1, pcc2, sdmmc4_rst_n_pcc3, sdmmc4_clk_pcc4,
+    clk2_req_pcc5, pex_l2_rst_n_pcc6, pex_l2_clkreq_n_pcc7,
+    pex_l0_prsnt_n_pdd0, pex_l0_rst_n_pdd1, pex_l0_clkreq_n_pdd2,
+    pex_wake_n_pdd3, pex_l1_prsnt_n_pdd4, pex_l1_rst_n_pdd5,
+    pex_l1_clkreq_n_pdd6, pex_l2_prsnt_n_pdd7, clk3_out_pee0, clk3_req_pee1,
+    clk1_req_pee2, hdmi_cec_pee3, clk_32k_in, core_pwr_req, cpu_pwr_req, owr,
+    pwr_int_n.
+
+  drive groups:
+
+    These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
+    nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all
+    support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode.
+
+    ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1,
+    dap2, dap3, dap4, dbg, ddc, dev3, gma, gmb, gmc, gmd, gme, gmf, gmg,
+    gmh, gpv, lcd1, lcd2, owr, sdio1, sdio2, sdio3, spi, uaa, uab, uart2,
+    uart3, uda, vi1.
+
+Example:
+
+	pinctrl@70000000 {
+		compatible = "nvidia,tegra30-pinmux";
+		reg = < 0x70000868 0xd0     /* Pad control registers */
+			0x70003000 0x3e0 >; /* Mux registers */
+	};
+
+Example board file extract:
+
+	pinctrl@70000000 {
+		sdmmc4_default: pinmux {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins =	"sdmmc4_clk_pcc4",
+						"sdmmc4_rst_n_pcc3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+			sdmmc4_dat0_paa0 {
+				nvidia,pins =	"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@78000400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc4_default>;
+	};

Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt

+== Introduction ==
+
+Hardware modules that control pin multiplexing or configuration parameters
+such as pull-up/down, tri-state, drive-strength etc are designated as pin
+controllers. Each pin controller must be represented as a node in device tree,
+just like any other hardware module.
+
+Hardware modules whose signals are affected by pin configuration are
+designated client devices. Again, each client device must be represented as a
+node in device tree, just like any other hardware module.
+
+For a client device to operate correctly, certain pin controllers must
+set up certain specific pin configurations. Some client devices need a
+single static pin configuration, e.g. set up during initialization. Others
+need to reconfigure pins at run-time, for example to tri-state pins when the
+device is inactive. Hence, each client device can define a set of named
+states. The number and names of those states is defined by the client device's
+own binding.
+
+The common pinctrl bindings defined in this file provide an infrastructure
+for client device device tree nodes to map those state names to the pin
+configuration used by those states.
+
+Note that pin controllers themselves may also be client devices of themselves.
+For example, a pin controller may set up its own "active" state when the
+driver loads. This would allow representing a board's static pin configuration
+in a single place, rather than splitting it across multiple client device
+nodes. The decision to do this or not somewhat rests with the author of
+individual board device tree files, and any requirements imposed by the
+bindings for the individual client devices in use by that board, i.e. whether
+they require certain specific named states for dynamic pin configuration.
+
+== Pinctrl client devices ==
+
+For each client device individually, every pin state is assigned an integer
+ID. These numbers start at 0, and are contiguous. For each state ID, a unique
+property exists to define the pin configuration. Each state may also be
+assigned a name. When names are used, another property exists to map from
+those names to the integer IDs.
+
+Each client device's own binding determines the set of states the must be
+defined in its device tree node, and whether to define the set of state
+IDs that must be provided, or whether to define the set of state names that
+must be provided.
+
+Required properties:
+pinctrl-0:	List of phandles, each pointing at a pin configuration
+		node. These referenced pin configuration nodes must be child
+		nodes of the pin controller that they configure. Multiple
+		entries may exist in this list so that multiple pin
+		controllers may be configured, or so that a state may be built
+		from multiple nodes for a single pin controller, each
+		contributing part of the overall configuration. See the next
+		section of this document for details of the format of these
+		pin configuration nodes.
+
+		In some cases, it may be useful to define a state, but for it
+		to be empty. This may be required when a common IP block is
+		used in an SoC either without a pin controller, or where the
+		pin controller does not affect the HW module in question. If
+		the binding for that IP block requires certain pin states to
+		exist, they must still be defined, but may be left empty.
+
+Optional properties:
+pinctrl-1:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+...
+pinctrl-n:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+pinctrl-names:	The list of names to assign states. List entry 0 defines the
+		name for integer state ID 0, list entry 1 for state ID 1, and
+		so on.
+
+For example:
+
+	/* For a client device requiring named states */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/* For the same device if using state IDs */
+	device {
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/*
+	 * For an IP block whose binding supports pin configuration,
+	 * but in use on an SoC that doesn't have any pin control hardware
+	 */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <>;
+		pinctrl-1 = <>;
+	};
+
+== Pin controller devices ==
+
+Pin controller devices should contain the pin configuration nodes that client
+devices reference.
+
+For example:
+
+	pincontroller {
+		... /* Standard DT properties for the device itself elided */
+
+		state_0_node_a {
+			...
+		};
+		state_1_node_a {
+			...
+		};
+		state_1_node_b {
+			...
+		};
+	}
+
+The contents of each of those pin configuration child nodes is defined
+entirely by the binding for the individual pin controller device. There
+exists no common standard for this content.
+
+The pin configuration nodes need not be direct children of the pin controller
+device; they may be grandchildren, for example. Whether this is legal, and
+whether there is any interaction between the child and intermediate parent
+nodes, is again defined entirely by the binding for the individual pin
+controller device.

Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt

+ST Microelectronics, SPEAr pinmux controller
+
+Required properties:
+- compatible	: "st,spear300-pinmux"
+		: "st,spear310-pinmux"
+		: "st,spear320-pinmux"
+- reg		: Address range of the pinctrl registers
+- st,pinmux-mode: Mandatory for SPEAr300 and SPEAr320 and invalid for others.
+	- Its values for SPEAr300:
+		- NAND_MODE		: <0>
+		- NOR_MODE		: <1>
+		- PHOTO_FRAME_MODE	: <2>
+		- LEND_IP_PHONE_MODE	: <3>
+		- HEND_IP_PHONE_MODE	: <4>
+		- LEND_WIFI_PHONE_MODE	: <5>
+		- HEND_WIFI_PHONE_MODE	: <6>
+		- ATA_PABX_WI2S_MODE	: <7>
+		- ATA_PABX_I2S_MODE	: <8>
+		- CAML_LCDW_MODE	: <9>
+		- CAMU_LCD_MODE		: <10>
+		- CAMU_WLCD_MODE	: <11>
+		- CAML_LCD_MODE		: <12>
+	- Its values for SPEAr320:
+		- AUTO_NET_SMII_MODE	: <0>
+		- AUTO_NET_MII_MODE	: <1>
+		- AUTO_EXP_MODE		: <2>
+		- SMALL_PRINTERS_MODE	: <3>
+		- EXTENDED_MODE		: <4>
+
+Please refer to pinctrl-bindings.txt in this directory for details of the common
+pinctrl bindings used by client devices.
+
+SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each
+of these subnodes represents muxing for a pin, a group, or a list of pins or
+groups.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Required subnode-properties:
+- st,pins : An array of strings. Each string contains the name of a pin or
+  group.
+- st,function: A string containing the name of the function to mux to the pin or
+  group. See the SPEAr's TRM to determine which are valid for each pin or group.
+
+  Valid values for group and function names can be found from looking at the
+  group and function arrays in driver files:
+  drivers/pinctrl/spear/pinctrl-spear3*0.c
+
+Valid values for group names are:
+For All SPEAr3xx machines:
+	"firda_grp", "i2c0_grp", "ssp_cs_grp", "ssp0_grp", "mii0_grp",
+	"gpio0_pin0_grp", "gpio0_pin1_grp", "gpio0_pin2_grp", "gpio0_pin3_grp",
+	"gpio0_pin4_grp", "gpio0_pin5_grp", "uart0_ext_grp", "uart0_grp",
+	"timer_0_1_grp", timer_0_1_pins, "timer_2_3_grp"
+
+For SPEAr300 machines:
+	"fsmc_2chips_grp", "fsmc_4chips_grp", "clcd_lcdmode_grp",
+	"clcd_pfmode_grp", "tdm_grp", "i2c_clk_grp_grp", "caml_grp", "camu_grp",
+	"dac_grp", "i2s_grp", "sdhci_4bit_grp", "sdhci_8bit_grp",
+	"gpio1_0_to_3_grp", "gpio1_4_to_7_grp"
+
+For SPEAr310 machines:
+	"emi_cs_0_to_5_grp", "uart1_grp", "uart2_grp", "uart3_grp", "uart4_grp",
+	"uart5_grp", "fsmc_grp", "rs485_0_grp", "rs485_1_grp", "tdm_grp"
+
+For SPEAr320 machines:
+	"clcd_grp", "emi_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "spp_grp",
+	"sdhci_led_grp", "sdhci_cd_12_grp", "sdhci_cd_51_grp", "i2s_grp",
+	"uart1_grp", "uart1_modem_2_to_7_grp", "uart1_modem_31_to_36_grp",
+	"uart1_modem_34_to_45_grp", "uart1_modem_80_to_85_grp", "uart2_grp",
+	"uart3_8_9_grp", "uart3_15_16_grp", "uart3_41_42_grp",
+	"uart3_52_53_grp", "uart3_73_74_grp", "uart3_94_95_grp",
+	"uart3_98_99_grp", "uart4_6_7_grp", "uart4_13_14_grp",
+	"uart4_39_40_grp", "uart4_71_72_grp", "uart4_92_93_grp",
+	"uart4_100_101_grp", "uart5_4_5_grp", "uart5_37_38_grp",
+	"uart5_69_70_grp", "uart5_90_91_grp", "uart6_2_3_grp",
+	"uart6_88_89_grp", "rs485_grp", "touchscreen_grp", "can0_grp",
+	"can1_grp", "pwm0_1_pin_8_9_grp", "pwm0_1_pin_14_15_grp",
+	"pwm0_1_pin_30_31_grp", "pwm0_1_pin_37_38_grp", "pwm0_1_pin_42_43_grp",
+	"pwm0_1_pin_59_60_grp", "pwm0_1_pin_88_89_grp", "pwm2_pin_7_grp",
+	"pwm2_pin_13_grp", "pwm2_pin_29_grp", "pwm2_pin_34_grp",
+	"pwm2_pin_41_grp", "pwm2_pin_58_grp", "pwm2_pin_87_grp",
+	"pwm3_pin_6_grp", "pwm3_pin_12_grp", "pwm3_pin_28_grp",
+	"pwm3_pin_40_grp", "pwm3_pin_57_grp", "pwm3_pin_86_grp",
+	"ssp1_17_20_grp", "ssp1_36_39_grp", "ssp1_48_51_grp", "ssp1_65_68_grp",
+	"ssp1_94_97_grp", "ssp2_13_16_grp", "ssp2_32_35_grp", "ssp2_44_47_grp",
+	"ssp2_61_64_grp", "ssp2_90_93_grp", "mii2_grp", "smii0_1_grp",
+	"rmii0_1_grp", "i2c1_8_9_grp", "i2c1_98_99_grp", "i2c2_0_1_grp",
+	"i2c2_2_3_grp", "i2c2_19_20_grp", "i2c2_75_76_grp", "i2c2_96_97_grp"
+
+Valid values for function names are:
+For All SPEAr3xx machines:
+	"firda", "i2c0", "ssp_cs", "ssp0", "mii0", "gpio0", "uart0_ext",
+	"uart0", "timer_0_1", "timer_2_3"
+
+For SPEAr300 machines:
+	"fsmc", "clcd", "tdm", "i2c1", "cam", "dac", "i2s", "sdhci", "gpio1"
+
+For SPEAr310 machines:
+	"emi", "uart1", "uart2", "uart3", "uart4", "uart5", "fsmc", "rs485_0",
+	"rs485_1", "tdm"
+
+For SPEAr320 machines:
+	"clcd", "emi", "fsmc", "spp", "sdhci", "i2s", "uart1", "uart1_modem",
+	"uart2", "uart3", "uart4", "uart5", "uart6", "rs485", "touchscreen",
+	"can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2",
+	"mii0_1", "i2c1", "i2c2"

Documentation/devicetree/bindings/pinmux/pinmux_nvidia.txt

-NVIDIA Tegra 2 pinmux controller
-
-Required properties:
-- compatible : "nvidia,tegra20-pinmux"
-

Documentation/driver-model/devres.txt

@@ -280,3 +280,7 @@ REGULATOR
 CLOCK
   devm_clk_get()
   devm_clk_put()
+
+PINCTRL
+  devm_pinctrl_get()
+  devm_pinctrl_put()

Documentation/pinctrl.txt

@@ -152,11 +152,9 @@ static const struct foo_group foo_groups[] = {
 };
 
 
-static int foo_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+static int foo_get_groups_count(struct pinctrl_dev *pctldev)
 {
-	if (selector >= ARRAY_SIZE(foo_groups))
-		return -EINVAL;
-	return 0;
+	return ARRAY_SIZE(foo_groups);
 }
 
 static const char *foo_get_group_name(struct pinctrl_dev *pctldev,
@@ -175,7 +173,7 @@ static int foo_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
 }
 
 static struct pinctrl_ops foo_pctrl_ops = {
-	.list_groups = foo_list_groups,
+	.get_groups_count = foo_get_groups_count,
 	.get_group_name = foo_get_group_name,
 	.get_group_pins = foo_get_group_pins,
 };
@@ -186,13 +184,12 @@ static struct pinctrl_desc foo_desc = {
        .pctlops = &foo_pctrl_ops,
 };
 
-The pin control subsystem will call the .list_groups() function repeatedly
-beginning on 0 until it returns non-zero to determine legal selectors, then
-it will call the other functions to retrieve the name and pins of the group.
-Maintaining the data structure of the groups is up to the driver, this is
-just a simple example - in practice you may need more entries in your group
-structure, for example specific register ranges associated with each group
-and so on.
+The pin control subsystem will call the .get_groups_count() function to
+determine total number of legal selectors, then it will call the other functions
+to retrieve the name and pins of the group. Maintaining the data structure of
+the groups is up to the driver, this is just a simple example - in practice you
+may need more entries in your group structure, for example specific register
+ranges associated with each group and so on.
 
 
 Pin configuration
@@ -606,11 +603,9 @@ static const struct foo_group foo_groups[] = {
 };
 
 
-static int foo_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+static int foo_get_groups_count(struct pinctrl_dev *pctldev)
 {
-	if (selector >= ARRAY_SIZE(foo_groups))
-		return -EINVAL;
-	return 0;
+	return ARRAY_SIZE(foo_groups);
 }
 
 static const char *foo_get_group_name(struct pinctrl_dev *pctldev,
@@ -629,7 +624,7 @@ static int foo_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
 }
 
 static struct pinctrl_ops foo_pctrl_ops = {
-	.list_groups = foo_list_groups,
+	.get_groups_count = foo_get_groups_count,
 	.get_group_name = foo_get_group_name,
 	.get_group_pins = foo_get_group_pins,
 };
@@ -640,7 +635,7 @@ struct foo_pmx_func {
 	const unsigned num_groups;
 };
 
-static const char * const spi0_groups[] = { "spi0_1_grp" };
+static const char * const spi0_groups[] = { "spi0_0_grp", "spi0_1_grp" };
 static const char * const i2c0_groups[] = { "i2c0_grp" };
 static const char * const mmc0_groups[] = { "mmc0_1_grp", "mmc0_2_grp",
 					"mmc0_3_grp" };
@@ -663,11 +658,9 @@ static const struct foo_pmx_func foo_functions[] = {
 	},
 };
 
-int foo_list_funcs(struct pinctrl_dev *pctldev, unsigned selector)
+int foo_get_functions_count(struct pinctrl_dev *pctldev)
 {
-	if (selector >= ARRAY_SIZE(foo_functions))
-		return -EINVAL;
-	return 0;
+	return ARRAY_SIZE(foo_functions);
 }
 
 const char *foo_get_fname(struct pinctrl_dev *pctldev, unsigned selector)
@@ -703,7 +696,7 @@ void foo_disable(struct pinctrl_dev *pctldev, unsigned selector,
 }
 
 struct pinmux_ops foo_pmxops = {
-	.list_functions = foo_list_funcs,
+	.get_functions_count = foo_get_functions_count,
 	.get_function_name = foo_get_fname,
 	.get_function_groups = foo_get_groups,
 	.enable = foo_enable,
@@ -786,7 +779,7 @@ and spi on the second function mapping:
 
 #include <linux/pinctrl/machine.h>
 
-static const struct pinctrl_map __initdata mapping[] = {
+static const struct pinctrl_map mapping[] __initconst = {
 	{
 		.dev_name = "foo-spi.0",
 		.name = PINCTRL_STATE_DEFAULT,
@@ -952,13 +945,13 @@ case), we define a mapping like this:
 The result of grabbing this mapping from the device with something like
 this (see next paragraph):
 
-	p = pinctrl_get(dev);
+	p = devm_pinctrl_get(dev);
 	s = pinctrl_lookup_state(p, "8bit");
 	ret = pinctrl_select_state(p, s);
 
 or more simply:
 
-	p = pinctrl_get_select(dev, "8bit");
+	p = devm_pinctrl_get_select(dev, "8bit");
 
 Will be that you activate all the three bottom records in the mapping at
 once. Since they share the same name, pin controller device, function and
@@ -992,7 +985,7 @@ foo_probe()
 	/* Allocate a state holder named "foo" etc */
 	struct foo_state *foo = ...;
 
-	foo->p = pinctrl_get(&device);
+	foo->p = devm_pinctrl_get(&device);
 	if (IS_ERR(foo->p)) {
 		/* FIXME: clean up "foo" here */
 		return PTR_ERR(foo->p);
@@ -1000,24 +993,17 @@ foo_probe()
 
 	foo->s = pinctrl_lookup_state(foo->p, PINCTRL_STATE_DEFAULT);
 	if (IS_ERR(foo->s)) {
-		pinctrl_put(foo->p);
 		/* FIXME: clean up "foo" here */
 		return PTR_ERR(s);
 	}
 
 	ret = pinctrl_select_state(foo->s);
 	if (ret < 0) {
-		pinctrl_put(foo->p);
 		/* FIXME: clean up "foo" here */
 		return ret;
 	}
 }
 
-foo_remove()
-{
-	pinctrl_put(state->p);
-}
-
 This get/lookup/select/put sequence can just as well be handled by bus drivers
 if you don't want each and every driver to handle it and you know the
 arrangement on your bus.
@@ -1029,6 +1015,11 @@ The semantics of the pinctrl APIs are:
   kernel memory to hold the pinmux state. All mapping table parsing or similar
   slow operations take place within this API.
 
+- devm_pinctrl_get() is a variant of pinctrl_get() that causes pinctrl_put()
+  to be called automatically on the retrieved pointer when the associated
+  device is removed. It is recommended to use this function over plain
+  pinctrl_get().
+
 - pinctrl_lookup_state() is called in process context to obtain a handle to a
   specific state for a the client device. This operation may be slow too.
 
@@ -1041,14 +1032,30 @@ The semantics of the pinctrl APIs are:
 
 - pinctrl_put() frees all information associated with a pinctrl handle.
 
+- devm_pinctrl_put() is a variant of pinctrl_put() that may be used to
+  explicitly destroy a pinctrl object returned by devm_pinctrl_get().
+  However, use of this function will be rare, due to the automatic cleanup
+  that will occur even without calling it.
+
+  pinctrl_get() must be paired with a plain pinctrl_put().
+  pinctrl_get() may not be paired with devm_pinctrl_put().
+  devm_pinctrl_get() can optionally be paired with devm_pinctrl_put().
+  devm_pinctrl_get() may not be paired with plain pinctrl_put().
+
 Usually the pin control core handled the get/put pair and call out to the
 device drivers bookkeeping operations, like checking available functions and
 the associated pins, whereas the enable/disable pass on to the pin controller
 driver which takes care of activating and/or deactivating the mux setting by
 quickly poking some registers.
 
-The pins are allocated for your device when you issue the pinctrl_get() call,
-after this you should be able to see this in the debugfs listing of all pins.
+The pins are allocated for your device when you issue the devm_pinctrl_get()
+call, after this you should be able to see this in the debugfs listing of all
+pins.
+
+NOTE: the pinctrl system will return -EPROBE_DEFER if it cannot find the
+requested pinctrl handles, for example if the pinctrl driver has not yet
+registered. Thus make sure that the error path in your driver gracefully
+cleans up and is ready to retry the probing later in the startup process.
 
 
 System pin control hogging
@@ -1094,13 +1101,13 @@ it, disables and releases it, and muxes it in on the pins defined by group B:
 
 #include <linux/pinctrl/consumer.h>
 
-foo_switch()
-{
-	struct pinctrl *p;
-	struct pinctrl_state *s1, *s2;
+struct pinctrl *p;
+struct pinctrl_state *s1, *s2;
 
+foo_probe()
+{
 	/* Setup */
-	p = pinctrl_get(&device);
+	p = devm_pinctrl_get(&device);
 	if (IS_ERR(p))
 		...
 
@@ -1111,7 +1118,10 @@ foo_switch()
 	s2 = pinctrl_lookup_state(foo->p, "pos-B");
 	if (IS_ERR(s2))
 		...
+}
 
+foo_switch()
+{
 	/* Enable on position A */
 	ret = pinctrl_select_state(s1);
 	if (ret < 0)
@@ -1125,8 +1135,6 @@ foo_switch()
 	    ...
 
 	...
-
-	pinctrl_put(p);
 }
 
 The above has to be done from process context.

MAINTAINERS

@@ -5242,6 +5242,14 @@ M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
 F:	drivers/pinctrl/
 
+PIN CONTROLLER - ST SPEAR
+M:	Viresh Kumar <viresh.kumar@st.com>
+L:	spear-devel@list.st.com
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+W:	http://www.st.com/spear
+S:	Maintained
+F:	driver/pinctrl/spear/
+
 PKTCDVD DRIVER
 M:	Peter Osterlund <petero2@telia.com>
 S:	Maintained
@@ -6336,21 +6344,6 @@ W:	http://www.st.com/spear
 S:	Maintained
 F:	drivers/clk/spear/
 
-SPEAR PAD MULTIPLEXING SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
-L:	spear-devel@list.st.com
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://www.st.com/spear
-S:	Maintained
-F:	arch/arm/plat-spear/include/plat/padmux.h
-F:	arch/arm/plat-spear/padmux.c
-F:	arch/arm/mach-spear*/spear*xx.c
-F:	arch/arm/mach-spear*/include/mach/generic.h
-F:	arch/arm/mach-spear3xx/spear3*0.c
-F:	arch/arm/mach-spear3xx/spear3*0_evb.c
-F:	arch/arm/mach-spear6xx/spear600.c
-F:	arch/arm/mach-spear6xx/spear600_evb.c
-
 SPI SUBSYSTEM
 M:	Grant Likely <grant.likely@secretlab.ca>
 L:	spi-devel-general@lists.sourceforge.net

arch/arm/Kconfig

@@ -470,6 +470,7 @@ config ARCH_MXS
 	select CLKSRC_MMIO
 	select COMMON_CLK
 	select HAVE_CLK_PREPARE
+	select PINCTRL
 	help
 	  Support for Freescale MXS-based family of processors
 

arch/arm/boot/dts/spear300-evb.dts

+/*
+ * DTS file for SPEAr300 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear300.dtsi"
+
+/ {
+	model = "ST SPEAr300 Evaluation Board";
+	compatible = "st,spear300-evb", "st,spear300";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@99000000 {
+			st,pinmux-mode = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				clcd {
+					st,pins = "clcd_pfmode_grp";
+					st,function = "clcd";
+				};
+				sdhci {
+					st,pins = "sdhci_4bit_grp";
+					st,function = "sdhci";
+				};
+				gpio1 {
+					st,pins = "gpio1_4_to_7_grp",
+						"gpio1_0_to_3_grp";
+					st,function = "gpio1";
+				};
+			};
+		};
+
+		clcd@60000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@94000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			int-gpio = <&gpio1 0 0>;
+			power-gpio = <&gpio1 2 1>;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio1: gpio@a9000000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			kbd@a0000000 {
+				linux,keymap = < 0x00000001
+						 0x00010002
+						 0x00020003
+						 0x00030004
+						 0x00040005
+						 0x00050006
+						 0x00060007
+						 0x00070008
+						 0x00080009
+						 0x0100000a
+						 0x0101000c
+						 0x0102000d
+						 0x0103000e
+						 0x0104000f
+						 0x01050010
+						 0x01060011
+						 0x01070012
+						 0x01080013
+						 0x02000014
+						 0x02010015
+						 0x02020016
+						 0x02030017
+						 0x02040018
+						 0x02050019
+						 0x0206001a
+						 0x0207001b
+						 0x0208001c
+						 0x0300001d
+						 0x0301001e
+						 0x0302001f
+						 0x03030020
+						 0x03040021
+						 0x03050022
+						 0x03060023
+						 0x03070024
+						 0x03080025
+						 0x04000026
+						 0x04010027
+						 0x04020028
+						 0x04030029
+						 0x0404002a
+						 0x0405002b
+						 0x0406002c
+						 0x0407002d
+						 0x0408002e
+						 0x0500002f
+						 0x05010030
+						 0x05020031
+						 0x05030032
+						 0x05040033
+						 0x05050034
+						 0x05060035
+						 0x05070036
+						 0x05080037
+						 0x06000038
+						 0x06010039
+						 0x0602003a
+						 0x0603003b
+						 0x0604003c
+						 0x0605003d
+						 0x0606003e
+						 0x0607003f
+						 0x06080040
+						 0x07000041
+						 0x07010042
+						 0x07020043
+						 0x07030044
+						 0x07040045
+						 0x07050046
+						 0x07060047
+						 0x07070048
+						 0x07080049
+						 0x0800004a
+						 0x0801004b
+						 0x0802004c
+						 0x0803004d
+						 0x0804004e
+						 0x0805004f
+						 0x08060050
+						 0x08070051
+						 0x08080052 >;
+			       autorepeat;
+			       st,mode = <0>;
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear300.dtsi

+/*
+ * DTS file for SPEAr300 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x60000000 0x60000000 0x50000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@99000000 {
+			compatible = "st,spear300-pinmux";
+			reg = <0x99000000 0x1000>;
+		};
+
+		clcd@60000000 {
+			compatible = "arm,clcd-pl110", "arm,primecell";
+			reg = <0x60000000 0x1000>;
+			interrupts = <30>;
+			status = "disabled";
+		};
+
+		fsmc: flash@94000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x94000000 0x1000	/* FSMC Register */
+			       0x80000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x20000>;
+			st,cle-off = <0x10000>;
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <1>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			gpio1: gpio@a9000000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xa9000000 0x1000>;
+				status = "disabled";
+			};
+
+			kbd@a0000000 {
+				compatible = "st,spear300-kbd";
+				reg = <0xa0000000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear310-evb.dts

+/*
+ * DTS file for SPEAr310 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear310.dtsi"
+
+/ {
+	model = "ST SPEAr310 Evaluation Board";
+	compatible = "st,spear310-evb", "st,spear310";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b4000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				gpio0 {
+					st,pins = "gpio0_pin0_grp",
+						"gpio0_pin1_grp",
+						"gpio0_pin2_grp",
+						"gpio0_pin3_grp",
+						"gpio0_pin4_grp",
+						"gpio0_pin5_grp";
+					st,function = "gpio0";
+				};
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				emi {
+					st,pins = "emi_cs_0_to_5_grp";
+					st,function = "emi";
+				};
+				fsmc {
+					st,pins = "fsmc_grp";
+					st,function = "fsmc";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				uart3 {
+					st,pins = "uart3_grp";
+					st,function = "uart3";
+				};
+				uart4 {
+					st,pins = "uart4_grp";
+					st,function = "uart4";
+				};
+				uart5 {
+					st,pins = "uart5_grp";
+					st,function = "uart5";
+				};
+			};
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@44000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			serial@b2000000 {
+			       status = "okay";
+			};
+
+			serial@b2080000 {
+			       status = "okay";
+			};
+
+			serial@b2100000 {
+			       status = "okay";
+			};
+
+			serial@b2180000 {
+			       status = "okay";
+			};
+
+			serial@b2200000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear310.dtsi

+/*
+ * DTS file for SPEAr310 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x10000000
+			  0xb0000000 0xb0000000 0x10000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@b4000000 {
+			compatible = "st,spear310-pinmux";
+			reg = <0xb4000000 0x1000>;
+		};
+
+		fsmc: flash@44000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x44000000 0x1000	/* FSMC Register */
+			       0x40000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x10000>;
+			st,cle-off = <0x20000>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xb0000000 0xb0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			serial@b2000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2080000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2080000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2100000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2100000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2180000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2180000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2200000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2200000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear320-evb.dts

+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+	model = "ST SPEAr300 Evaluation Board";
+	compatible = "st,spear300-evb", "st,spear300";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b3000000 {
+			st,pinmux-mode = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				sdhci {
+					st,pins = "sdhci_cd_51_grp";
+					st,function = "sdhci";
+				};
+				i2s {
+					st,pins = "i2s_grp";
+					st,function = "i2s";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				can0 {
+					st,pins = "can0_grp";
+					st,function = "can0";
+				};
+				can1 {
+					st,pins = "can1_grp";
+					st,function = "can1";
+				};
+				mii2 {
+					st,pins = "mii2_grp";
+					st,function = "mii2";
+				};
+				pwm0_1 {
+					st,pins = "pwm0_1_pin_14_15_grp";
+					st,function = "pwm0_1";
+				};
+				pwm2 {
+					st,pins = "pwm2_pin_13_grp";
+					st,function = "pwm2";
+				};
+			};
+		};
+
+		clcd@90000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@4c000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			power-gpio = <&gpio0 2 1>;
+			power_always_enb;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		spi1: spi@a5000000 {
+			status = "okay";
+		};
+
+		spi2: spi@a6000000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			i2c1: i2c@a7000000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			serial@a3000000 {
+			       status = "okay";
+			};
+
+			serial@a4000000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear320.dtsi

+/*
+ * DTS file for SPEAr320 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x80000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@b3000000 {
+			compatible = "st,spear320-pinmux";
+			reg = <0xb3000000 0x1000>;
+		};
+
+		clcd@90000000 {
+			compatible = "arm,clcd-pl110", "arm,primecell";
+			reg = <0x90000000 0x1000>;
+			interrupts = <33>;
+			status = "disabled";
+		};
+
+		fsmc: flash@4c000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x4c000000 0x1000	/* FSMC Register */
+			       0x50000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x20000>;
+			st,cle-off = <0x10000>;
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <29>;
+			status = "disabled";
+		};
+
+		spi1: spi@a5000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa5000000 0x1000>;
+			status = "disabled";
+		};
+
+		spi2: spi@a6000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa6000000 0x1000>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			i2c1: i2c@a7000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xa7000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@a3000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa3000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@a4000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa4000000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear3xx.dtsi

+/*
+ * DTS file for all SPEAr3xx SoCs
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&vic>;
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm926ejs";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+		vic: interrupt-controller@f1100000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xf1100000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic>;
+			interrupts = <8>;
+			status = "disabled";
+		};
+
+		gmac: eth@e0800000 {
+			compatible = "st,spear600-gmac";
+			reg = <0xe0800000 0x8000>;
+			interrupts = <23 22>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			status = "disabled";
+		};
+
+		smi: flash@fc000000 {
+			compatible = "st,spear600-smi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xfc000000 0x1000>;
+			interrupts = <9>;
+			status = "disabled";
+		};
+
+		spi0: spi@d0100000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xd0100000 0x1000>;
+			interrupts = <20>;
+			status = "disabled";
+		};
+
+		ehci@e1800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe1800000 0x1000>;
+			interrupts = <26>;
+			status = "disabled";
+		};
+
+		ohci@e1900000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe1900000 0x1000>;
+			interrupts = <25>;
+			status = "disabled";
+		};
+
+		ohci@e2100000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe2100000 0x1000>;
+			interrupts = <27>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+			gpio0: gpio@fc980000 {
+				compatible = "arm,pl061", "arm,primecell";
+				reg = <0xfc980000 0x1000>;
+				interrupts = <11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@d0180000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xd0180000 0x1000>;
+				interrupts = <21>;
+				status = "disabled";
+			};
+
+			rtc@fc900000 {
+				compatible = "st,spear-rtc";
+				reg = <0xfc900000 0x1000>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
+			serial@d0000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xd0000000 0x1000>;
+				interrupts = <19>;
+				status = "disabled";
+			};
+
+			wdt@fc880000 {
+				compatible = "arm,sp805", "arm,primecell";
+				reg = <0xfc880000 0x1000>;
+				interrupts = <12>;
+				status = "disabled";
+			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupts = <2>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear600-evb.dts

@@ -24,11 +24,44 @@ memory {
 	};
 
 	ahb {
+		dma@fc400000 {
+			status = "okay";
+		};
+
 		gmac: ethernet@e0800000 {
 			phy-mode = "gmii";
 			status = "okay";
 		};
 
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
+		};
+
 		apb {
 			serial@d0000000 {
 				status = "okay";

arch/arm/boot/dts/spear600.dtsi

@@ -45,6 +45,14 @@ vic1: interrupt-controller@f1000000 {
 			#interrupt-cells = <1>;
 		};
 
+		dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <10>;
+			status = "disabled";
+		};
+
 		gmac: ethernet@e0800000 {
 			compatible = "st,spear600-gmac";
 			reg = <0xe0800000 0x8000>;
@@ -169,6 +177,12 @@ i2c@d0200000 {
 				interrupts = <28>;
 				status = "disabled";
 			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupts = <16>;
+			};
 		};
 	};
 };

arch/arm/configs/spear3xx_defconfig

@@ -2,33 +2,70 @@ CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
-CONFIG_BOARD_SPEAR300_EVB=y
-CONFIG_BOARD_SPEAR310_EVB=y
-CONFIG_BOARD_SPEAR320_EVB=y
+CONFIG_MACH_SPEAR300=y
+CONFIG_MACH_SPEAR310=y
+CONFIG_MACH_SPEAR320=y
 CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
 CONFIG_INPUT_FF_MEMLESS=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_SPEAR=y
 # CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
 CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
 # CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_FB_ARMCLCD=y
 # CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SPEAR=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_SECURITY=y
@@ -39,8 +76,7 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
+CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
@@ -48,6 +84,4 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
 CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set

arch/arm/configs/spear6xx_defconfig

@@ -2,29 +2,60 @@ CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
 CONFIG_ARCH_SPEAR6XX=y
-CONFIG_BOARD_SPEAR600_EVB=y
 CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
 CONFIG_INPUT_FF_MEMLESS=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_RAW_DRIVER=y
 CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
 # CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
 # CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_SECURITY=y
@@ -35,8 +66,7 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
+CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
@@ -44,6 +74,4 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
 CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set

arch/arm/mach-imx/Kconfig

@@ -850,6 +850,8 @@ config SOC_IMX6Q
 	select HAVE_IMX_MMDC
 	select HAVE_IMX_SRC
 	select HAVE_SMP
+	select PINCTRL
+	select PINCTRL_IMX6Q
 	select USE_OF
 
 	help

arch/arm/mach-imx/imx51-dt.c

@@ -14,6 +14,7 @@
 #include <linux/irqdomain.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/pinctrl/machine.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <mach/common.h>
@@ -81,6 +82,8 @@ static void __init imx51_dt_init(void)
 
 	of_irq_init(imx51_irq_match);
 
+	pinctrl_provide_dummies();
+
 	node = of_find_matching_node(NULL, imx51_iomuxc_of_match);
 	if (node) {
 		of_id = of_match_node(imx51_iomuxc_of_match, node);

arch/arm/mach-imx/imx53-dt.c

@@ -15,6 +15,7 @@
 #include <linux/irqdomain.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/pinctrl/machine.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <mach/common.h>
@@ -88,6 +89,8 @@ static void __init imx53_dt_init(void)
 
 	of_irq_init(imx53_irq_match);
 
+	pinctrl_provide_dummies();
+
 	node = of_find_matching_node(NULL, imx53_iomuxc_of_match);
 	if (node) {
 		of_id = of_match_node(imx53_iomuxc_of_match, node);

arch/arm/mach-imx/mach-imx6q.c

@@ -19,6 +19,7 @@
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
+#include <linux/pinctrl/machine.h>
 #include <linux/phy.h>
 #include <linux/micrel_phy.h>
 #include <asm/smp_twd.h>
@@ -77,6 +78,12 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 
 static void __init imx6q_init_machine(void)
 {
+	/*
+	 * This should be removed when all imx6q boards have pinctrl
+	 * states for devices defined in device tree.
+	 */
+	pinctrl_provide_dummies();
+
 	if (of_machine_is_compatible("fsl,imx6q-sabrelite"))
 		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
 					   ksz9021rn_phy_fixup);

arch/arm/mach-imx/mm-imx1.c

@@ -18,6 +18,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/mach/map.h>
 
@@ -58,4 +59,5 @@ void __init imx1_soc_init(void)
 						MX1_GPIO_INT_PORTC, 0);
 	mxc_register_gpio("imx1-gpio", 3, MX1_GPIO4_BASE_ADDR, SZ_256,
 						MX1_GPIO_INT_PORTD, 0);
+	pinctrl_provide_dummies();
 }

arch/arm/mach-imx/mm-imx21.c

@@ -20,6 +20,7 @@
 
 #include <linux/mm.h>
 #include <linux/init.h>
+#include <linux/pinctrl/machine.h>
 #include <mach/hardware.h>
 #include <mach/common.h>
 #include <mach/devices-common.h>
@@ -88,6 +89,7 @@ void __init imx21_soc_init(void)
 	mxc_register_gpio("imx21-gpio", 4, MX21_GPIO5_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
 	mxc_register_gpio("imx21-gpio", 5, MX21_GPIO6_BASE_ADDR, SZ_256, MX21_INT_GPIO, 0);
 
+	pinctrl_provide_dummies();
 	imx_add_imx_dma();
 	platform_device_register_simple("imx21-audmux", 0, imx21_audmux_res,
 					ARRAY_SIZE(imx21_audmux_res));

arch/arm/mach-imx/mm-imx25.c

@@ -19,6 +19,7 @@
 #include <linux/mm.h>
 #include <linux/init.h>
 #include <linux/err.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/pgtable.h>
 #include <asm/mach/map.h>
@@ -95,6 +96,7 @@ void __init imx25_soc_init(void)
 	mxc_register_gpio("imx31-gpio", 2, MX25_GPIO3_BASE_ADDR, SZ_16K, MX25_INT_GPIO3, 0);
 	mxc_register_gpio("imx31-gpio", 3, MX25_GPIO4_BASE_ADDR, SZ_16K, MX25_INT_GPIO4, 0);
 
+	pinctrl_provide_dummies();
 	/* i.mx25 has the i.mx35 type sdma */
 	imx_add_imx_sdma("imx35-sdma", MX25_SDMA_BASE_ADDR, MX25_INT_SDMA, &imx25_sdma_pdata);
 	/* i.mx25 has the i.mx31 type audmux */

arch/arm/mach-imx/mm-imx27.c

@@ -20,6 +20,7 @@
 
 #include <linux/mm.h>
 #include <linux/init.h>
+#include <linux/pinctrl/machine.h>
 #include <mach/hardware.h>
 #include <mach/common.h>
 #include <mach/devices-common.h>
@@ -89,6 +90,7 @@ void __init imx27_soc_init(void)
 	mxc_register_gpio("imx21-gpio", 4, MX27_GPIO5_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
 	mxc_register_gpio("imx21-gpio", 5, MX27_GPIO6_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
 
+	pinctrl_provide_dummies();
 	imx_add_imx_dma();
 	/* imx27 has the imx21 type audmux */
 	platform_device_register_simple("imx21-audmux", 0, imx27_audmux_res,

arch/arm/mach-imx/mm-imx3.c

@@ -19,6 +19,7 @@
 #include <linux/mm.h>
 #include <linux/init.h>
 #include <linux/err.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/pgtable.h>
 #include <asm/system_misc.h>
@@ -273,6 +274,7 @@ void __init imx35_soc_init(void)
 	mxc_register_gpio("imx31-gpio", 1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
 	mxc_register_gpio("imx31-gpio", 2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
 
+	pinctrl_provide_dummies();
 	if (to_version == 1) {
 		strncpy(imx35_sdma_pdata.fw_name, "sdma-imx35-to1.bin",
 			strlen(imx35_sdma_pdata.fw_name));

arch/arm/mach-imx/mm-imx5.c

@@ -14,6 +14,7 @@
 #include <linux/mm.h>
 #include <linux/init.h>
 #include <linux/clk.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/system_misc.h>
 #include <asm/mach/map.h>
@@ -224,6 +225,7 @@ void __init imx53_soc_init(void)
 	mxc_register_gpio("imx31-gpio", 5, MX53_GPIO6_BASE_ADDR, SZ_16K, MX53_INT_GPIO6_LOW, MX53_INT_GPIO6_HIGH);
 	mxc_register_gpio("imx31-gpio", 6, MX53_GPIO7_BASE_ADDR, SZ_16K, MX53_INT_GPIO7_LOW, MX53_INT_GPIO7_HIGH);
 
+	pinctrl_provide_dummies();
 	/* i.mx53 has the i.mx35 type sdma */
 	imx_add_imx_sdma("imx35-sdma", MX53_SDMA_BASE_ADDR, MX53_INT_SDMA, &imx53_sdma_pdata);
 

arch/arm/mach-mxs/Kconfig

@@ -9,11 +9,13 @@ config SOC_IMX23
 	bool
 	select CPU_ARM926T
 	select HAVE_PWM
+	select PINCTRL_IMX23
 
 config SOC_IMX28
 	bool
 	select CPU_ARM926T
 	select HAVE_PWM
+	select PINCTRL_IMX28
 
 comment "MXS platforms:"
 

arch/arm/mach-mxs/include/mach/common.h

@@ -17,11 +17,13 @@ extern void mxs_timer_init(int);
 extern void mxs_restart(char, const char *);
 extern int mxs_saif_clkmux_select(unsigned int clkmux);
 
+extern void mx23_soc_init(void);
 extern int mx23_register_gpios(void);
 extern int mx23_clocks_init(void);
 extern void mx23_map_io(void);
 extern void mx23_init_irq(void);
 
+extern void mx28_soc_init(void);
 extern int mx28_register_gpios(void);
 extern int mx28_clocks_init(void);
 extern void mx28_map_io(void);

arch/arm/mach-mxs/mach-apx4devkit.c

@@ -207,6 +207,8 @@ static int apx4devkit_phy_fixup(struct phy_device *phy)
 
 static void __init apx4devkit_init(void)
 {
+	mx28_soc_init();
+
 	mxs_iomux_setup_multiple_pads(apx4devkit_pads,
 			ARRAY_SIZE(apx4devkit_pads));
 

arch/arm/mach-mxs/mach-m28evk.c

@@ -319,6 +319,8 @@ static struct mxs_mmc_platform_data m28evk_mmc_pdata[] __initdata = {
 
 static void __init m28evk_init(void)
 {
+	mx28_soc_init();
+
 	mxs_iomux_setup_multiple_pads(m28evk_pads, ARRAY_SIZE(m28evk_pads));
 
 	mx28_add_duart();

arch/arm/mach-mxs/mach-mx23evk.c

@@ -141,6 +141,8 @@ static void __init mx23evk_init(void)
 {
 	int ret;
 
+	mx23_soc_init();
+
 	mxs_iomux_setup_multiple_pads(mx23evk_pads, ARRAY_SIZE(mx23evk_pads));
 
 	mx23_add_duart();

arch/arm/mach-mxs/mach-mx28evk.c

@@ -413,6 +413,8 @@ static void __init mx28evk_init(void)
 {
 	int ret;
 
+	mx28_soc_init();
+
 	mxs_iomux_setup_multiple_pads(mx28evk_pads, ARRAY_SIZE(mx28evk_pads));
 
 	mx28_add_duart();

arch/arm/mach-mxs/mach-stmp378x_devb.c

@@ -85,6 +85,8 @@ static void __init stmp378x_dvb_init(void)
 {
 	int ret;
 
+	mx23_soc_init();
+
 	mxs_iomux_setup_multiple_pads(stmp378x_dvb_pads,
 			ARRAY_SIZE(stmp378x_dvb_pads));
 

arch/arm/mach-mxs/mach-tx28.c

@@ -146,6 +146,8 @@ static struct mxs_mmc_platform_data tx28_mmc0_pdata __initdata = {
 
 static void __init tx28_stk5v3_init(void)
 {
+	mx28_soc_init();
+
 	mxs_iomux_setup_multiple_pads(tx28_stk5v3_pads,
 			ARRAY_SIZE(tx28_stk5v3_pads));
 

arch/arm/mach-mxs/mm.c

@@ -13,6 +13,7 @@
 
 #include <linux/mm.h>
 #include <linux/init.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/mach/map.h>
 
@@ -61,3 +62,13 @@ void __init mx28_init_irq(void)
 {
 	icoll_init_irq();
 }
+
+void __init mx23_soc_init(void)
+{
+	pinctrl_provide_dummies();
+}
+
+void __init mx28_soc_init(void)
+{
+	pinctrl_provide_dummies();
+}