- 21 Sep, 2016 10 commits
-
-
Chen-Yu Tsai authored
EHCI1 provides an HSIC interface. This interface is exposed on the board through two pins among the GPIO header. With the PHY now powered up and responding, enabling the interface when nothing is connected results in a lot of error messages: usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new high-speed USB device number 3 using ehci-platform usb 2-1: device descriptor read/64, error -71 usb 2-1: device descriptor read/64, error -71 usb 2-1: new high-speed USB device number 4 using ehci-platform usb 2-1: device not accepting address 4, error -71 usb 2-1: new high-speed USB device number 5 using ehci-platform usb 2-1: device not accepting address 5, error -71 usb usb2-port1: unable to enumerate USB device Disable it by default, but leave the entries in the board DTS. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The AXP806 PMIC is the secondary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by:
-
Chen-Yu Tsai authored
The AXP806 PMIC is the secondary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by:
-
Chen-Yu Tsai authored
The AXP809's SW (switch) regulator is unused on the Cubieboard 4. Add an empty node for it so that the OS can generate constraints. Signed-off-by:
-
Chen-Yu Tsai authored
The AXP809's SW (switch) regulator is unused on the A80 Optimus. Add an empty node for it so that the OS can generate constraints. Signed-off-by:
-
Hans de Goede authored
The ga10h tablet has a gsl3675 touchscreen, add a dt node describing it. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Add a node enabling the gsl3670 touchscreen controller found on sun8i-a23-polaroid-mid2809pxe04 tablets. Signed-off-by:
-
Hans de Goede authored
Add a node enabling the gsl1680 touchscreen controller found on sun8i-a23-polaroid-mid2407pxe03 tablets. Signed-off-by:
-
Hans de Goede authored
The inet86dz tablet has a gsl1680 touchscreen, add a dt node describing it. Signed-off-by:
-
Hans de Goede authored
The gt90h tablet has a gsl3675 touchscreen, add a dt node describing it. Signed-off-by:
-
- 11 Sep, 2016 2 commits
-
-
Mylène Josserand authored
The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND, an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI, I2S and LCD. Signed-off-by:
Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by:
-
Mylène Josserand authored
The GR8 is an SoC made by Nextthing loosely based on the sun5i family. Since it's not clear yet what we can factor out and merge with the A10s and A13 support, let's keep it out of the sun5i.dtsi include tree. We will figure out what can be shared when things settle down. Signed-off-by:
-
- 10 Sep, 2016 14 commits
-
-
Chen-Yu Tsai authored
The usbphy and usb_otg nodes in the A23 and A33 dts files only differ by compatible, and for the usbphy, the size of one of its register regions. Move all the common bits to the A23/A33 common dtsi file. Signed-off-by:
-
Maxime Ripard authored
The LCD output needs to be muxed. Add the proper pinctrl node. Signed-off-by:
-
Maxime Ripard authored
Add all the needed blocks to the A33 DTSI. Signed-off-by:
-
Maxime Ripard authored
Now that we have support for the CCU driver in sunxi-ng, convert the A23 and A33 DTs to that driver. Signed-off-by:
-
Chen-Yu Tsai authored
Now that we have a different clock representation, switch to it. Signed-off-by:
-
Maxime Ripard authored
-
Jean Delvare authored
The sunxi-ng clock driver is useless for other architectures. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Acked-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Maxime Ripard authored
Add support for the clock unit found in the A23. Due to the similarities with the A33, it also shares its clock IDs to allow sharing the DTSI. Signed-off-by:
-
Maxime Ripard authored
This commit introduces the clocks found in the Allwinner A33 CCU. Since this SoC is very similar to the A23, and we share a significant share of the DTSI, the clock IDs that are going to be used will also be shared with the A23, hence the name of the various header files. Signed-off-by:
-
Maxime Ripard authored
Add support for the class with a single factor, N, being a multiplier. Signed-off-by:
-
Maxime Ripard authored
Add a new macro to declare muxes based on a table and a gate. Signed-off-by:
-
Maxime Ripard authored
Some dividers might have a maximum value that is lower than the width of the register. Add a field to _ccu_div to handle those case properly. If the field is set to 0, the code will assume that the maximum value is the maximum one that can be used with the field register width. Otherwise, we'll use whatever value has been set. Signed-off-by:
-
Maxime Ripard authored
The internal _ccu_div structure is meant to be embedded into other structures to combine the various dividers and to form the clock classes support. Start to document those structures by using kerneldoc. Signed-off-by: -
Maxime Ripard authored
Add some macros to ease the declaration of clocks that are using them. Signed-off-by:
-
- 06 Sep, 2016 2 commits
-
-
James Pettigrew authored
Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor. Signed-off-by:
James Pettigrew <james@innovum.com.au> Reviewed-by:
Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk> Acked-by:
-
James Pettigrew authored
The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a micro SD slot, 10/100Mbit ethernet and a single USB-A port. Signed-off-by:
-
- 05 Sep, 2016 3 commits
-
-
Hans de Goede authored
Most of the sun8i q8 boards have an SDIO wifi controller, on the variants which use an USB wifi controller, this will result in a couple of error msg-s in dmesg when proving the sdio bus and an used mmc controller. The best way to deal with wifi on this boards really is to simply let the kernel auto-detect usb or sdio wifi controllers, so we will just have to live with the few errors in dmesg. This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and RTL8189FTV wifi controllers. Signed-off-by:
-
Hans de Goede authored
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus, with 2G RAM and an external gbit ethernet phy. Note currently the dts is pretty much empty (except for including the pc-plus dts), I've a local patch which enables the emac actually making this dts different from the pc-plus one, but that needs the h3 emac driver to get merged first. Signed-off-by:
-
Hans de Goede authored
Update the sun8i-h3-orangepi-plus.dts model string to reflect that it is valid for both the Orange Pi Plus and the Orange Pi Plus 2. This is also meant to help users realize that it is not valid for the new Orange Pi Plus 2E, which will get its own dts. Signed-off-by:
-
- 31 Aug, 2016 1 commit
-
-
Milo Kim authored
Acked-by:
Milo Kim <woogyom.kim@gmail.com> Signed-off-by:
-
- 27 Aug, 2016 2 commits
-
-
Icenowy Zheng authored
The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features volume buttons, micro-usb otg, headphone connector and a power button. On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there is also a accompanied board which has a Goodix GT9271 soldered. As this board is desired to create tablets with a Home key dealed by GT9271, a LED is present at the front panel at the position of the Home key. Signed-off-by:
Icenowy Zheng <icenowy@aosc.xyz> Signed-off-by:
-
Chen-Yu Tsai authored
The R_PIO device node is missing #interrupt-cells, which causes interrupt parsing to fail to match it as a valid interrupt controller. Add #interrupt-cells to it. Also remove the unnecesary #address-cells and #size-cells. Fixes: 1ac56a6d ("ARM: dts: sun9i: Add A80 R_PIO pin controller device node") Signed-off-by:
-
- 26 Aug, 2016 6 commits
-
-
Hans de Goede authored
Rename the reference-design-tablet touchscreen node from gsl1680 to touchscreen, all? tablets seem to use the same power and interrupt gpio-s, but not all tablets use a gsl1680 controller making the gsl1680 name somewhat misleading. Also move the reg and compatible property to the actual tablet dts as they may differ per tablet. Signed-off-by:
-
Hans de Goede authored
Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV wifi chip and a DMART06 (1238a4) accelerometer. Note currently the dts for this is somewhat empty. This will change once we add support for the touchscreen and accelerometer. Signed-off-by:
-
Hans de Goede authored
This results in a nice cleanup :) Signed-off-by:
-
Hans de Goede authored
The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi module soldered on the PCB, so there enabling ohci1 is not necessary. Signed-off-by:
-
Hans de Goede authored
The polaroid-mid2809 tablet has an esp8089 wifi chip, add a dt node describing it. Signed-off-by:
-
Hans de Goede authored
The polaroid-mid2407 tablet has an esp8089 wifi chip, add a dt node describing it. Signed-off-by:
-
