intel-pinctrl for v5.10-2

* Respect bias setting when comes from ACPI

The following is an automated git shortlog grouped by driver:

intel:
 -  Set default bias in case no particular value given
 -  Fix 2 kOhm bias which is 833 Ohm

Fix the check on the number of IRQs to allow up to the maximum (32)
instead of only the maximum minus one.

Fixes: 96868dce ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20201107081420.60325-10-damien.lemoal@wdc.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'gpio-fixes-for-v5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes

gpio fixes for v5.10-rc3

- fix missing conversion to gpiolib irqchip in gpio-dwapb
- fix bank properties for ast2600 variant in gpio-aspeed
- make sysfs work again when the character device is disabled
- fix interrupt handling in gpio-pcie-idio-24

This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.

Fixes: 58556204 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

This fixes the COS Enable Register value for enabling/disabling the
corresponding IRQs bank.

Fixes: 58556204 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Fix the bitwise operation to remove only the corresponding bit from the
mask.

Fixes: 58556204 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

In gpiochip_setup_dev() the call to gpiolib_cdev_register() indirectly
calls device_add().  This is still required for the sysfs even when
CONFIG_GPIO_CDEV is not selected in the build.

Replace the stubbed functions in gpiolib-cdev.h with macros in gpiolib.c
that perform the required device_add() and device_del() when
CONFIG_GPIO_CDEV is not selected.

Fixes: d143493c (gpiolib: make cdev a build option)
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Address code indentation warning messages by checkpatch script. Combine
split function parameters on one line. This also resolves the "use tabs
instead of space" warning by checkpatch script.
Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>

Link: https://lore.kernel.org/r/20201013190212.GA85788@ubuntu204Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 579ced8f.

Turns out I was overly optimistic about cpu_pm blocking idle being a
solution for handling edge interrupts. While it helps in preventing
entering idle states that potentially lose context, we can still get
an edge interrupt triggering while entering idle. So we need to also
add back the workaround for seeing if there are any pending edge
interrupts when waking up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20201028060556.56038-1-tony@atomide.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

We actually handle the gpio_irq_chip set-up properly
now despite what the comment says. Also assign this
pointer along with the rest of the gpio_irq_chip
setup code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201019134429.65563-1-linus.walleij@linaro.org

Now that all gpiolib irqchip users have been over to use
the irqchip template, we can finally retire the old code
path and leave just one way in to the irqchip: set up the
template when registering the gpio_chip. For a while
we had two code paths for this which was a bit confusing.

This brings this work to a conclusion, there is now one
way of doing this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://lore.kernel.org/r/20201019134046.65101-1-linus.walleij@linaro.org

Use the new compat_need_64bit_alignment_fixup() helper to avoid
ugly ifdeffery in IOCTL compatibility code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Depends-on: 527c4125 ("compat: add a compat_need_64bit_alignment_fixup() helper")
Link: https://lore.kernel.org/r/20201014103315.82662-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

First of all, bias has a special type as being a part of enum pin_config_param.
Second, 0 is also defined bias which is equivalent to BUS_HOLD.

Taking into account above, change type of bias variable and refactor
gpio_set_bias() in a way that it doesn't use BUS_HOLD as a place holder.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201009184359.16427-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Clarify that a char array containing a string is considered 'empty' if
the first character is the null terminator. The remaining characters
are not relevant to this determination.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201005070329.21055-6-warthog618@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove leading whitespace in ABI v1 comment.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201005070329.21055-5-warthog618@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add kernel-doc formatting to all references to structs, enums, fields
and constants, and move deprecation warnings into the Note section of
the deprecated struct.

Replace 'OR:ed' with 'added', as the former looks odd.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201005070329.21055-4-warthog618@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Make debounce_period_us field documentation consistent with other fields
in the union.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201005070329.21055-3-warthog618@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix kernel-doc warnings, specifically gpioline_info_changed.padding is
not documented and 'GPIO event types' describes defines, which are not
documented by kernel-doc.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201005070329.21055-2-warthog618@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO_T is mapped to the most significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_T is input only. All
the other bits need to be 1 because GPIO_Q/R/S support both input and
output modes.

Fixes: ab4a8553 ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Commit 0ea68393 ("gpio: dwapb: Convert driver to using the
GPIO-lib-based IRQ-chip") missed the case in dwapb_irq_set_wake().

Without this fix, probing the dwapb gpio driver will hit a error:
"address between user and kernel address ranges" on a Ampere armv8a
server and cause a panic.

Fixes: 0ea68393 ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Jia He <justin.he@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.

In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).

Fixes: e57725ea ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:

	000	none
	001	1 kOhm (if available)
	010	5 kOhm
	100	20 kOhm

As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:

	011	~833.3 Ohm
	101	~952.4 Ohm
	110	~4 kOhm
	111	~800 Ohm

That said, convert TERM definitions to be the bit masks to reflect the above.

While at it, enable the same setting for pull down case.

Fixes: 7981c001 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Pull SafeSetID updates from Micah Morton:
 "The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Pull random32 updates from Willy Tarreau:
 "Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/

* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

Commit 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a41 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>