Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.

Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two more eBPF test cases for JITs, i.e. the second one revealed a
bug in the x86_64 JIT compiler, where only an int3 filled image from
the allocator was emitted and later wrongly set by the compiler as the
bpf_func program code since optimization pass boundary was surpassed
w/o actually emitting opcodes.

Interpreter:

  [   45.782892] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:0 11 PASS
  [   45.783062] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:0 14705 PASS

After x86_64 JIT (fixed):

  [   80.495638] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:1 6 PASS
  [   80.495957] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:1 17157 PASS

Reference: http://thread.gmane.org/gmane.linux.network/364729Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2015-05-22

The following patches are included in this driver update series:

- Retrieve and set an additional hardware feature setting
- Fix the initial mode/speed determination when auto-negotiation is
  disabled
- Add additional netif_dbg support to the driver

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.

Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send icmp pmtu error if we find that the largest fragment of df-skb
exceeded the output path mtu.

The ip output path will still catch this later on but we can avoid the
forward/postrouting hook traversal by rejecting right away.

This is what ipv6 already does.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hannes Frederic Sowa says:

====================
net: af_unix: zerocopy stream bits

This series implements zerocopy support for AF_UNIX SOCK_STREAM sockets.

Changelog in the specific patches. Thanks to all the reviewers!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

unix_stream_recvmsg is refactored to unix_stream_read_generic in this
patch and enhanced to deal with pipe splicing. The refactoring is
inneglible, we mostly have to deal with a non-existing struct msghdr
argument.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare skb_splice_bits to be able to deal with AF_UNIX sockets.

AF_UNIX sockets don't use lock_sock/release_sock and thus we have to
use a callback to make the locking and unlocking configureable.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements sendpage support for AF_UNIX SOCK_STREAM
sockets. This is also required for a complete splice implementation.

The implementation is a bit tricky because we append to already existing
skbs and so have to hold unix_sk->readlock to protect the reading side
from either advancing UNIXCB.consumed or freeing the skb at the socket
receive tail.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
ath10k:

* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware

ath9k:

* spectral scan: add support for multiple FFT frames per report

iwlwifi:

* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure

brcmfmac:

* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Enable single ported VFs over IB ports

This series further enhances the support for mlx4 single ported VFs
introduced in 3.15 to work over IB ports too.

Just as quick reminder, the ConnectX3 device family exposes one PCI device
which serves both ports.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

Since all the VF interaction with the firmware passes through the PF
driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.

SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.

Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.

To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.

This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.

(1) make sure that events are generated only for VFs sitting on
    the relevant physical port (under the ALL_SLAVES flow).

(2) before generating the event, convert from physical (one or two)
    to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).

This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.

So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.

It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/cadence/macb.c
	drivers/net/phy/phy.c
	include/linux/skbuff.h
	net/ipv4/tcp.c
	net/switchdev/switchdev.c

Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.

phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.

tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.

macb.c involved the addition of two zyncq device entries.

skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
pktgen: cleanups and introducing new samples/pktgen scripts

v3:
 - Aborted v2 send due it was not generating diff stat
   (this is a bug in stg-mail, if not in the root directory)

v2: address nitpicks from Cong Wang
 - Remove useless cat's, but keep them for old pgset()
 - Comment on: Due to pgctrl, cannot use exit code $? from grep
 - Use arithmetic compare in pktgen_sample03_burst_single_flow.sh

This patchset is focused on making pktgen easier to use and better
documented. It contains a number of documentation updates and minor
changes to pktgen.  The major contribution is introduction of common
helper function for sample scripts.

Instead of the old pgset() function, three new shell functions for
configuring the different components of pktgen are introduced:
 pg_ctrl(), pg_thread() and pg_set().

The new functions correspond to pktgens different components.
 * pg_ctrl()   control "pgctrl" (/proc/net/pktgen/pgctrl)
 * pg_thread() control the kernel threads and binding to devices
 * pg_set()    control setup of individual devices

Helpers also provide consistent parameter parsing across the sample
scripts.

Usage example:
 ./pktgen_sample01_simple.sh -i eth41 -m 00:12:C0:02:AC:5A -d 192.168.41.2

Usage: ./pktgen_sample01_simple.sh [-vx] -i ethX
  -i : ($DEV)       output interface/device (required)
  -s : ($PKT_SIZE)  packet size
  -d : ($DEST_IP)   destination IP
  -m : ($DST_MAC)   destination MAC-addr
  -t : ($THREADS)   threads to start
  -c : ($SKB_CLONE) SKB clones send before alloc new SKB
  -b : ($BURST)     HW level bursting of SKBs
  -v : ($VERBOSE)   verbose
  -x : ($DEBUG)     debug

These scripts are borrowed from:
 https://github.com/netoptimizer/network-testing/tree/master/pktgen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This script pktgen_bench_xmit_mode_netif_receive.sh is a benchmark
script, which can be used for benchmarking part of the network stack.
This can be used for performance improving or catching regression in
that area.

The script is developed for benchmarking ingress qdisc path, original
idea by Alexei Starovoitov.  This script don't really need any
hardware.  This is achieved via the recently introduced stack inject
feature "xmit_mode netif_receive". See commit 62f64aed ("pktgen:
introduce xmit_mode '<start_xmit|netif_receive>'").
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the pktgen samples script pktgen_sample03_burst_single_flow.sh
that demonstrates how to acheive maximum performance.

If correctly tuned[1] single CPU 10Gbit/s wirespeed small pkts is
possible[2] which is 14.88Mpps.  The trick is to take advantage of the
"burst" feature introduced in commit 38b2cf29 ("net: pktgen:
packet bursting via skb->xmit_more").

[1] http://netoptimizer.blogspot.dk/2014/06/pktgen-for-network-overload-testing.html
[2] http://netoptimizer.blogspot.dk/2014/10/unlocked-10gbps-tx-wirespeed-smallest.htmlSigned-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the pktgen samples script pktgen_sample02_multiqueue.sh that
demonstrates generating packets on multiqueue NICs.

Specifically notice the options "-t" that specifies how many
kernel threads to activate.  Also notice the flag QUEUE_MAP_CPU,
which cause the SKB TX queue to be mapped to the CPU running the
kernel thread.  For best scalability people are also encourage to
map NIC IRQ /proc/irq/*/smp_affinity to CPU number.

Usage example with "-t" 4 threads and help:
 ./pktgen_sample02_multiqueue.sh -i eth4 -m 00:1B:21:3C:9D:F8 -t 4

Usage: ./pktgen_sample02_multiqueue.sh [-vx] -i ethX
  -i : ($DEV)       output interface/device (required)
  -s : ($PKT_SIZE)  packet size
  -d : ($DEST_IP)   destination IP
  -m : ($DST_MAC)   destination MAC-addr
  -t : ($THREADS)   threads to start
  -c : ($SKB_CLONE) SKB clones send before alloc new SKB
  -b : ($BURST)     HW level bursting of SKBs
  -v : ($VERBOSE)   verbose
  -x : ($DEBUG)     debug

Removing pktgen.conf-2-1 and pktgen.conf-2-2 as these examples
should be covered now.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the first basic pktgen samples script pktgen_sample01_simple.sh,
which demonstrates the a simple use of the helper functions.
Removing pktgen.conf-1-1 as that example should be covered now.

The naming scheme pktgen_sampleNN, where NN is a number, should encourage
reading the samples in a specific order.

Script cause pktgen sending with a single thread and single interface,
and introduce flow variation via random UDP source port.

Usage example and help:
 ./pktgen_sample01_simple.sh -i eth4 -m 00:1B:21:3C:9D:F8 -d 192.168.8.2

Usage: ./pktgen_sample01_simple.sh [-vx] -i ethX
  -i : ($DEV)       output interface/device (required)
  -s : ($PKT_SIZE)  packet size
  -d : ($DEST_IP)   destination IP
  -m : ($DST_MAC)   destination MAC-addr
  -c : ($SKB_CLONE) SKB clones send before alloc new SKB
  -v : ($VERBOSE)   verbose
  -x : ($DEBUG)     debug
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Preparing for removing existing samples/pktgen/ scripts, and
replacing these with easier to use samples.

This commit provides two helper shell files, that can
be "included" by shell source'ing. Namely "functions.sh"
and "parameters.sh".

The parameters.sh file support easy and consistant parameter
parsing across the sample scripts.  Usage example is printed on
errors.

The functions.sh file provides, three new shell functions for
configuring the different components of pktgen: pg_ctrl(),
pg_thread() and pg_set().  A slightly improved version of the old
pgset() function is also provided for backwards compat.

The new functions correspond to pktgens different components.
 * pg_ctrl()   control "pgctrl" (/proc/net/pktgen/pgctrl)
 * pg_thread() control the kernel threads and binding to devices
 * pg_set()    control setup of individual devices

These changes are borrowed from:
 https://github.com/netoptimizer/network-testing/tree/master/pktgenSigned-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Giving /proc/net/pktgen/pgctrl an invalid command just returns shell
success and prints a warning in dmesg.  This is not very useful for
shell scripting, as it can only detect the error by parsing dmesg.

Instead return -EINVAL when the command is unknown, as this provides
userspace shell scripting a way of detecting this.

Also bump version tag to 2.75, because (1) reading /proc/net/pktgen/pgctrl
output this version number which would allow to detect this small
semantic change, and (2) because the pktgen version tag have not been
updated since 2010.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pktgen.txt documentation still claimed that adding same device to
multiple threads were not supported, but it have been since 2008 via
commit e6fce5b9 ("pktgen: multiqueue etc.").

Document this and describe the naming scheme dev@X, as the procfile name
still need to be unique.

Fixes: e6fce5b9 ("pktgen: multiqueue etc.")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pktgen.txt documentation over available config options were not complete.
Making the list complete by adding the following.

Pgcontrol commands:
 reset

Device commands:
 burst
 queue_map_min
 queue_map_max
 skb_priority
 tos
 traffic_class
 node
 spi
 dst6_max
 dst6_min
 vlan_cfi
 vlan_id
 vlan_p
 svlan_cfi
 svlan_id
 svlan_p
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Too many spaces were introduced in commit 63adc6fb ("pktgen: cleanup
checkpatch warnings"), thus misaligning "src_min:" to other columns.

Fixes: 63adc6fb ("pktgen: cleanup checkpatch warnings")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And cleanup some whitespaces in pktgen.txt.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "Radeon has two displayport fixes, one for a regression.

  i915 regression flicker fix needed so 4.0 can get fixed.

  A bunch of msm fixes and a bunch of exynos fixes, these two are
  probably a bit larger than I'd like, but most of them seems pretty
  good"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
  drm/radeon: fix error flag checking in native aux path
  drm/radeon: retry dcpd fetch
  drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
  drm/exynos: dp: Lower level of EDID read success message
  drm/exynos: cleanup exynos_drm_plane
  drm/exynos: 'win' is always unsigned
  drm/exynos: mixer: don't dump registers under spinlock
  drm/exynos: Consolidate return statements in fimd_bind()
  drm/exynos: Constify exynos_drm_crtc_ops
  drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
  drm/exynos: mixer: Constify platform_device_id
  drm/exynos: mixer: cleanup pixelformat handling
  drm/exynos: mixer: also allow NV21 for the video processor
  drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
  drm/exynos: plane: honor buffer offset for dma_addr
  drm/exynos: fb: use drm_format_num_planes to get buffer count
  drm/i915: fix screen flickering
  drm/msm: fix locking inconsistencies in gpu->destroy()
  drm/msm/dsi: Simplify the code to get the number of read byte
  drm/msm: Attach assigned encoder to eDP and DSI connectors
  ...

Pull networking fixes from David Miller:

 1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.

 2) Fix neighbour table entry leak in rocker driver, from Ying Xue.

 3) Do not emit bonding notifications for unregistered interfaces, from
    Nicolas Dichtel.

 4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
    Fourcot.

 5) Fix regression in ipv6 multicast filter test, from Henning Rogge.

 6) do_replace() in various footables netfilter modules is missing a
    check for 0 counters in the datastructure provided by the user.  Fix
    from Dave Jones, and found with trinity.

 7) Fix RCU bug in packet scheduler classifier module unloads, from
    Daniel Borkmann.

 8) Avoid deadlock in tcp_get_info() by using u64_sync.  From Eric
    Dumzaet.

 9) Input packet processing can race with inetdev_destroy() teardown,
    fix potential OOPS in ip_error() by explicitly testing whether the
    inetdev is still attached.  From Eric W Biederman.

10) MLDv2 parser in bridge multicast code breaks too early while
    parsing.  Fix from Thadeu Lima de Souza Cascardo.

11) Asking for settings on non-zero PHYID doesn't work because we do not
    import the command structure from the user and use the PHYID
    provided there.  Fix from Arun Parameswaran.

12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.

13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
    fix from Florian Westphal.

14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
    from Jesper Dangaard Brouer.

15) If netlink autobind retry fails, we have to reset the sockets portid
    back to zero.  From Herbert Xu.

16) VXLAN netns exit code unregisters using wrong device, from John W
    Linville.

17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
    Dmitry Tunin and Wen-chien Jesse Sung.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  bridge: fix lockdep splat
  net: core: 'ethtool' issue with querying phy settings
  bridge: fix parsing of MLDv2 reports
  ARM: zynq: DT: Use the zynq binding with macb
  net: macb: Disable half duplex gigabit on Zynq
  net: macb: Document zynq gem dt binding
  ipv4: fill in table id when replacing a route
  cdc_ncm: Fix tx_bytes statistics
  ipv4: Avoid crashing in ip_error
  tcp: fix a potential deadlock in tcp_get_info()
  net: sched: fix call_rcu() race on classifier module unloads
  net: phy: Make sure phy_start() always re-enables the phy interrupts
  ipv6: fix ECMP route replacement
  ipv6: do not delete previously existing ECMP routes if add fails
  Revert "netfilter: bridge: query conntrack about skb dnat"
  netfilter: ensure number of counters is >0 in do_replace()
  netfilter: nfnetlink_{log,queue}: Register pernet in first place
  tcp: don't over-send F-RTO probes
  tcp: only undo on partial ACKs in CA_Loss
  net/ipv6/udp: Fix ipv6 multicast socket filter regression
  ...

Pull block fixes from Jens Axboe:
 "Three small fixes that have been picked up the last few weeks.
  Specifically:

   - Fix a memory corruption issue in NVMe with malignant user
     constructed request.  From Christoph.

   - Kill (now) unused blk_queue_bio(), dm was changed to not need this
     anymore.  From Mike Snitzer.

   - Always use blk_schedule_flush_plug() from the io_schedule() path
     when flushing a plug, fixing a !TASK_RUNNING warning with md.  From
     Shaohua"

* 'for-linus' of git://git.kernel.dk/linux-block:
  sched: always use blk_schedule_flush_plug in io_schedule_out
  nvme: fix kernel memory corruption with short INQUIRY buffers
  block: remove export for blk_queue_bio

Pull md bugfixes from Neil Brown:
 "I have a few more raid5 bugfixes pending, but I want them to get a bit
  more review first.  In the meantime:

   - one serious RAID0 data corruption - caused by recent bugfix that
     wasn't reviewed properly.

   - one raid5 fix in new code (a couple more of those to come).

   - one little fix to stop static analysis complaining about silly rcu
     annotation"

* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
  md/bitmap: remove rcu annotation from pointer arithmetic.
  md/raid0: fix restore to sector variable in raid0_make_request
  raid5: fix broken async operation chain

Pull input fixes from Dmitry Torokhov:
 "Updates for the input subsystem.

  The main change is that we tell joydev not to touch "absolute mice",
  such as VMware virtual mouse, as that produced bad result (cursor
  stuck in upper right corner) with games"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: smtpe-ts - wait 50mS until polling for pen-up
  Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
  Input: joydev - don't classify the vmmouse as a joystick
  Input: vmmouse - do not reference non-existing version of X driver
  Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
  Input: elantech - fix semi-mt protocol for v3 HW
  Input: sx8654 - fix memory allocation check

Pull another crypto fix from Herbert Xu:
 "Fix ICV corruption in s390/ghash when the same tfm is used by more
  than one thread"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: s390/ghash - Fix incorrect ghash icv buffer handling.

Following lockdep splat was reported :

[   29.382286] ===============================
[   29.382315] [ INFO: suspicious RCU usage. ]
[   29.382344] 4.1.0-0.rc0.git11.1.fc23.x86_64 #1 Not tainted
[   29.382380] -------------------------------
[   29.382409] net/bridge/br_private.h:626 suspicious
rcu_dereference_check() usage!
[   29.382455]
               other info that might help us debug this:

[   29.382507]
               rcu_scheduler_active = 1, debug_locks = 0
[   29.382549] 2 locks held by swapper/0/0:
[   29.382576]  #0:  (((&p->forward_delay_timer))){+.-...}, at:
[<ffffffff81139f75>] call_timer_fn+0x5/0x4f0
[   29.382660]  #1:  (&(&br->lock)->rlock){+.-...}, at:
[<ffffffffa0450dc1>] br_forward_delay_timer_expired+0x31/0x140
[bridge]
[   29.382754]
               stack backtrace:
[   29.382787] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.1.0-0.rc0.git11.1.fc23.x86_64 #1
[   29.382838] Hardware name: LENOVO 422916G/LENOVO, BIOS A1KT53AUS 04/07/2015
[   29.382882]  0000000000000000 3ebfc20364115825 ffff880666603c48
ffffffff81892d4b
[   29.382943]  0000000000000000 ffffffff81e124e0 ffff880666603c78
ffffffff8110bcd7
[   29.383004]  ffff8800785c9d00 ffff88065485ac58 ffff880c62002800
ffff880c5fc88ac0
[   29.383065] Call Trace:
[   29.383084]  <IRQ>  [<ffffffff81892d4b>] dump_stack+0x4c/0x65
[   29.383130]  [<ffffffff8110bcd7>] lockdep_rcu_suspicious+0xe7/0x120
[   29.383178]  [<ffffffffa04520f9>] br_fill_ifinfo+0x4a9/0x6a0 [bridge]
[   29.383225]  [<ffffffffa045266b>] br_ifinfo_notify+0x11b/0x4b0 [bridge]
[   29.383271]  [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[   29.383320]  [<ffffffffa0450de8>]
br_forward_delay_timer_expired+0x58/0x140 [bridge]
[   29.383371]  [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[   29.383416]  [<ffffffff8113a033>] call_timer_fn+0xc3/0x4f0
[   29.383454]  [<ffffffff81139f75>] ? call_timer_fn+0x5/0x4f0
[   29.383493]  [<ffffffff8110a90f>] ? lock_release_holdtime.part.29+0xf/0x200
[   29.383541]  [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[   29.383587]  [<ffffffff8113a6a4>] run_timer_softirq+0x244/0x490
[   29.383629]  [<ffffffff810b68cc>] __do_softirq+0xec/0x670
[   29.383666]  [<ffffffff810b70d5>] irq_exit+0x145/0x150
[   29.383703]  [<ffffffff8189f506>] smp_apic_timer_interrupt+0x46/0x60
[   29.383744]  [<ffffffff8189d523>] apic_timer_interrupt+0x73/0x80
[   29.383782]  <EOI>  [<ffffffff816f131f>] ? cpuidle_enter_state+0x5f/0x2f0
[   29.383832]  [<ffffffff816f131b>] ? cpuidle_enter_state+0x5b/0x2f0

Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.

Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Dominick Grift <dac.override@gmail.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>