- 16 Mar, 2021 8 commits
-
-
Tong Zhang authored
There is a UAF in c_can_pci_remove(). dev is released by free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later. To fix this issue, save the mmio address before releasing dev. Fixes: 5b92da04 ("c_can_pci: generic module for C_CAN/D_CAN on PCI") Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.comSigned-off-by:
Tong Zhang <ztong0001@gmail.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Jimmy Assarsson authored
Add support for Kvaser USBcan Pro 4xHS. Link: https://lore.kernel.org/r/20210309091724.31262-2-jimmyassarsson@gmail.comSigned-off-by:
Jimmy Assarsson <extja@kvaser.com> Signed-off-by:
-
Jimmy Assarsson authored
Under certain circumstances, when switching from Kvaser's linuxcan driver (kvpciefd) to the SocketCAN driver (kvaser_pciefd), the bus load reporting is not disabled. This is flooding the kernel log with prints like: [3485.574677] kvaser_pciefd 0000:02:00.0: Received unexpected packet type 0x00000009 Always put the controller in the expected state, instead of assuming that bus load reporting is inactive. Note: If bus load reporting is enabled when the driver is loaded, you will still get a number of bus load packages (and printouts), before it is disabled. Fixes: 26ad340e ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Link: https://lore.kernel.org/r/20210309091724.31262-1-jimmyassarsson@gmail.comSigned-off-by: -
Angelo Dureghello authored
For cases when flexcan is built-in, bitrate is still not set at registering. So flexcan_chip_freeze() generates: [ 1.860000] *** ZERO DIVIDE *** FORMAT=4 [ 1.860000] Current process id is 1 [ 1.860000] BAD KERNEL TRAP: 00000000 [ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8 To allow chip freeze, using an hardcoded timeout when bitrate is still not set. Fixes: ec15e27c ("can: flexcan: enable RX FIFO after FRZ/HALT valid") Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.orgSigned-off-by:
Angelo Dureghello <angelo@kernel-space.org> [mkl: use if instead of ? operator] Signed-off-by:
-
Stephane Grosjean authored
Since the peak_usb driver also supports the CAN-USB interfaces "PCAN-USB X6" and "PCAN-Chip USB" from PEAK-System GmbH, this patch adds their names to the list of explicitly supported devices. Fixes: ea8b65b5 ("can: usb: Add support of PCAN-Chip USB stamp module") Fixes: f00b534d ("can: peak: Add support for PCAN-USB X6 USB interface") Link: https://lore.kernel.org/r/20210309082128.23125-3-s.grosjean@peak-system.comSigned-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by:
-
Marc Kleine-Budde authored
The previous patch ensures that the TX flags (struct can_isotp_ll_options::tx_flags) are 0 for classic CAN frames or a user configured value for CAN-FD frames. This patch sets the CAN frames flags unconditionally to the ISO-TP TX flags, so that they are initialized to a proper value. Otherwise when running "candump -x" on a classical CAN ISO-TP stream shows wrongly set "B" and "E" flags. | $ candump any,0:0,#FFFFFFFF -extA | [...] | can0 TX B E 713 [8] 2B 0A 0B 0C 0D 0E 0F 00 | can0 TX B E 713 [8] 2C 01 02 03 04 05 06 07 | can0 TX B E 713 [8] 2D 08 09 0A 0B 0C 0D 0E | can0 TX B E 713 [8] 2E 0F 00 01 02 03 04 05 Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/r/20210218215434.1708249-2-mkl@pengutronix.de Cc: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Marc Kleine-Budde authored
CAN-FD frames have struct canfd_frame::flags, while classic CAN frames don't. This patch refuses to set TX flags (struct can_isotp_ll_options::tx_flags) on non CAN-FD isotp sockets. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/r/20210218215434.1708249-2-mkl@pengutronix.de Cc: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Martin Willi authored
When a non-initial netns is destroyed, the usual policy is to delete all virtual network interfaces contained, but move physical interfaces back to the initial netns. This keeps the physical interface visible on the system. CAN devices are somewhat special, as they define rtnl_link_ops even if they are physical devices. If a CAN interface is moved into a non-initial netns, destroying that netns lets the interface vanish instead of moving it back to the initial netns. default_device_exit() skips CAN interfaces due to having rtnl_link_ops set. Reproducer: ip netns add foo ip link set can0 netns foo ip netns delete foo WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60 CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1 Workqueue: netns cleanup_net [<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14) [<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8) [<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114) [<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac) [<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60) [<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380) [<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438) [<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8) [<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c) [<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c) To properly restore physical CAN devices to the initial netns on owning netns exit, introduce a flag on rtnl_link_ops that can be set by drivers. For CAN devices setting this flag, default_device_exit() considers them non-virtual, applying the usual namespace move. The issue was introduced in the commit mentioned below, as at that time CAN devices did not have a dellink() operation. Fixes: e008b5fc ("net: Simplfy default_device_exit and improve batching.") Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.orgSigned-off-by:
Martin Willi <martin@strongswan.org> Signed-off-by:
-
- 15 Mar, 2021 5 commits
-
-
Davide Caratti authored
Currently, Linux computes the HMAC contained in ADD_ADDR sub-option using the Address Id and the IP Address, and hardcodes a destination port equal to zero. This is not ok for ADD_ADDR with port: ensure to account for the endpoint port when computing the HMAC, in compliance with RFC8684 §3.4.1. Fixes: 22fb85ff ("mptcp: add port support for ADD_ADDR suboption writing") Reviewed-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Acked-by:
Geliang Tang <geliangtang@gmail.com> Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Ovechkin authored
Currently tcp_check_req can be called with obsolete req socket for which big socket have been already created (because of CPU race or early demux assigning req socket to multiple packets in gro batch). Commit e0f9759f ("tcp: try to keep packet if SYN_RCV race is lost") added retry in case when tcp_check_req is called for PSH|ACK packet. But if client sends RST+ACK immediatly after connection being established (it is performing healthcheck, for example) retry does not occur. In that case tcp_check_req tries to close req socket, leaving big socket active. Fixes: e0f9759f ("tcp: try to keep packet if SYN_RCV race is lost") Signed-off-by:
Alexander Ovechkin <ovov@yandex-team.ru> Reported-by:
Oleg Senin <olegsenin@yandex-team.ru> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
Before calling tipc_aead_key_size(ptr), we need to ensure we have enough data to dereference ptr->keylen. We probably also want to make sure tipc_aead_key_size() wont overflow with malicious ptr->keylen values. Syzbot reported: BUG: KMSAN: uninit-value in __tipc_nl_node_set_key net/tipc/node.c:2971 [inline] BUG: KMSAN: uninit-value in tipc_nl_node_set_key+0x9bf/0x13b0 net/tipc/node.c:3023 CPU: 0 PID: 21060 Comm: syz-executor.5 Not tainted 5.11.0-rc7-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:120 kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x5f/0xa0 mm/kmsan/kmsan_instr.c:197 __tipc_nl_node_set_key net/tipc/node.c:2971 [inline] tipc_nl_node_set_key+0x9bf/0x13b0 net/tipc/node.c:3023 genl_family_rcv_msg_doit net/netlink/genetlink.c:739 [inline] genl_family_rcv_msg net/netlink/genetlink.c:783 [inline] genl_rcv_msg+0x1319/0x1610 net/netlink/genetlink.c:800 netlink_rcv_skb+0x6fa/0x810 net/netlink/af_netlink.c:2494 genl_rcv+0x63/0x80 net/netlink/genetlink.c:811 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline] netlink_unicast+0x11d6/0x14a0 net/netlink/af_netlink.c:1330 netlink_sendmsg+0x1740/0x1840 net/netlink/af_netlink.c:1919 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg net/socket.c:672 [inline] ____sys_sendmsg+0xcfc/0x12f0 net/socket.c:2345 ___sys_sendmsg net/socket.c:2399 [inline] __sys_sendmsg+0x714/0x830 net/socket.c:2432 __compat_sys_sendmsg net/compat.c:347 [inline] __do_compat_sys_sendmsg net/compat.c:354 [inline] __se_compat_sys_sendmsg+0xa7/0xc0 net/compat.c:351 __ia32_compat_sys_sendmsg+0x4a/0x70 net/compat.c:351 do_syscall_32_irqs_on arch/x86/entry/common.c:79 [inline] __do_fast_syscall_32+0x102/0x160 arch/x86/entry/common.c:141 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:166 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:209 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c RIP: 0023:0xf7f60549 Code: 03 74 c0 01 10 05 03 74 b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00 RSP: 002b:00000000f555a5fc EFLAGS: 00000296 ORIG_RAX: 0000000000000172 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000020000200 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:121 [inline] kmsan_internal_poison_shadow+0x5c/0xf0 mm/kmsan/kmsan.c:104 kmsan_slab_alloc+0x8d/0xe0 mm/kmsan/kmsan_hooks.c:76 slab_alloc_node mm/slub.c:2907 [inline] __kmalloc_node_track_caller+0xa37/0x1430 mm/slub.c:4527 __kmalloc_reserve net/core/skbuff.c:142 [inline] __alloc_skb+0x2f8/0xb30 net/core/skbuff.c:210 alloc_skb include/linux/skbuff.h:1099 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline] netlink_sendmsg+0xdbc/0x1840 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg net/socket.c:672 [inline] ____sys_sendmsg+0xcfc/0x12f0 net/socket.c:2345 ___sys_sendmsg net/socket.c:2399 [inline] __sys_sendmsg+0x714/0x830 net/socket.c:2432 __compat_sys_sendmsg net/compat.c:347 [inline] __do_compat_sys_sendmsg net/compat.c:354 [inline] __se_compat_sys_sendmsg+0xa7/0xc0 net/compat.c:351 __ia32_compat_sys_sendmsg+0x4a/0x70 net/compat.c:351 do_syscall_32_irqs_on arch/x86/entry/common.c:79 [inline] __do_fast_syscall_32+0x102/0x160 arch/x86/entry/common.c:141 do_fast_syscall_32+0x6a/0xc0 arch/x86/entry/common.c:166 do_SYSENTER_32+0x73/0x90 arch/x86/entry/common.c:209 entry_SYSENTER_compat_after_hwframe+0x4d/0x5c Fixes: e1f32190 ("tipc: add support for AEAD key setting via netlink") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Ong Boon Leong authored
if pl->mac_ops->mac_finish() failed, phylink_err should use "mac_finish" instead of "mac_prepare". Fixes: b7ad14c2 ("net: phylink: re-implement interface configuration with PCS") Signed-off-by:
Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
-
Xie He authored
"x25_close" is called by "hdlc_close" in "hdlc.c", which is called by hardware drivers' "ndo_stop" function. "x25_xmit" is called by "hdlc_start_xmit" in "hdlc.c", which is hardware drivers' "ndo_start_xmit" function. "x25_rx" is called by "hdlc_rcv" in "hdlc.c", which receives HDLC frames from "net/core/dev.c". "x25_close" races with "x25_xmit" and "x25_rx" because their callers race. However, we need to ensure that the LAPB APIs called in "x25_xmit" and "x25_rx" are called before "lapb_unregister" is called in "x25_close". This patch adds locking to ensure when "x25_xmit" and "x25_rx" are doing their work, "lapb_unregister" is not yet called in "x25_close". Reasons for not solving the racing between "x25_close" and "x25_xmit" by calling "netif_tx_disable" in "x25_close": 1. We still need to solve the racing between "x25_close" and "x25_rx"; 2. The design of the HDLC subsystem assumes the HDLC hardware drivers have full control over the TX queue, and the HDLC protocol drivers (like this driver) have no control. Controlling the queue here in the protocol driver may interfere with hardware drivers' control of the queue. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Xie He <xie.he.0141@gmail.com> Signed-off-by:
-
- 14 Mar, 2021 4 commits
-
-
Alexander Lobakin authored
flow_dissector_key_icmp::id is of type u16 (CPU byteorder), ICMP header has its ID field in network byteorder obviously. Sparse says: net/core/flow_dissector.c:178:43: warning: restricted __be16 degrades to integer Convert ID value to CPU byteorder when storing it into flow_dissector_key_icmp. Fixes: 5dec597e ("flow_dissector: extract more ICMP information") Signed-off-by:
Alexander Lobakin <alobakin@pm.me> Signed-off-by:
-
Eric Dumazet authored
struct sockaddr_qrtr has a 2-byte hole, and qrtr_recvmsg() currently does not clear it before copying kernel data to user space. It might be too late to name the hole since sockaddr_qrtr structure is uapi. BUG: KMSAN: kernel-infoleak in kmsan_copy_to_user+0x9c/0xb0 mm/kmsan/kmsan_hooks.c:249 CPU: 0 PID: 29705 Comm: syz-executor.3 Not tainted 5.11.0-rc7-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:120 kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118 kmsan_internal_check_memory+0x202/0x520 mm/kmsan/kmsan.c:402 kmsan_copy_to_user+0x9c/0xb0 mm/kmsan/kmsan_hooks.c:249 instrument_copy_to_user include/linux/instrumented.h:121 [inline] _copy_to_user+0x1ac/0x270 lib/usercopy.c:33 copy_to_user include/linux/uaccess.h:209 [inline] move_addr_to_user+0x3a2/0x640 net/socket.c:237 ____sys_recvmsg+0x696/0xd50 net/socket.c:2575 ___sys_recvmsg net/socket.c:2610 [inline] do_recvmmsg+0xa97/0x22d0 net/socket.c:2710 __sys_recvmmsg net/socket.c:2789 [inline] __do_sys_recvmmsg net/socket.c:2812 [inline] __se_sys_recvmmsg+0x24a/0x410 net/socket.c:2805 __x64_sys_recvmmsg+0x62/0x80 net/socket.c:2805 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x465f69 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f43659d6188 EFLAGS: 00000246 ORIG_RAX: 000000000000012b RAX: ffffffffffffffda RBX: 000000000056bf60 RCX: 0000000000465f69 RDX: 0000000000000008 RSI: 0000000020003e40 RDI: 0000000000000003 RBP: 00000000004bfa8f R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000010060 R11: 0000000000000246 R12: 000000000056bf60 R13: 0000000000a9fb1f R14: 00007f43659d6300 R15: 0000000000022000 Local variable ----addr@____sys_recvmsg created at: ____sys_recvmsg+0x168/0xd50 net/socket.c:2550 ____sys_recvmsg+0x168/0xd50 net/socket.c:2550 Bytes 2-3 of 12 are uninitialized Memory access of size 12 starts at ffff88817c627b40 Data copied to user address 0000000020000140 Fixes: bdabad3e ("net: Add Qualcomm IPC router") Signed-off-by:
-
Tong Zhang authored
There are two issues when handling error case in com20020pci_probe() 1. priv might be not initialized yet when calling com20020pci_remove() from com20020pci_probe(), since the priv is set at the very last but it can jump to error handling in the middle and priv remains NULL. 2. memory leak - the net device is allocated in alloc_arcdev but not properly released if error happens in the middle of the big for loop [ 1.529110] BUG: kernel NULL pointer dereference, address: 0000000000000008 [ 1.531447] RIP: 0010:com20020pci_remove+0x15/0x60 [com20020_pci] [ 1.536805] Call Trace: [ 1.536939] com20020pci_probe+0x3f2/0x48c [com20020_pci] [ 1.537226] local_pci_probe+0x48/0x80 [ 1.539918] com20020pci_init+0x3f/0x1000 [com20020_pci] Signed-off-by:
-
Eva Dengler authored
This commit fixes three spelling typos in devlink-dpipe.rst and devlink-port.rst. Signed-off-by:
Eva Dengler <eva.dengler@fau.de> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
- 13 Mar, 2021 9 commits
-
-
Alex Elder authored
When a QMI handle is initialized, an array of message handler structures is provided, defining how any received message should be handled based on its type and message ID. The QMI core code traverses this array when a message arrives and calls the function associated with the (type, msg_id) found in the array. The array is supposed to be terminated with an empty (all zero) entry though. Without it, an unsupported message will cause the QMI core code to go past the end of the array. Fix this bug, by properly terminating the message handler arrays provided when QMI handles are set up by the IPA driver. Fixes: 530f9216 ("soc: qcom: ipa: AP/modem communications") Reported-by:
Sujit Kautkar <sujitka@chromium.org> Signed-off-by:
Alex Elder <elder@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/gitDavid S. Miller authored
/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-03-12 This series contains updates to ice, i40e, ixgbe and igb drivers. Magnus adjusts the return value for xsk allocation for ice. This fixes reporting of napi work done and matches the behavior of other Intel NIC drivers for xsk allocations. Maciej moves storing of the rx_offset value to after the build_skb flag is set as this flag affects the offset value for ice, i40e, and ixgbe. Li RongQing resolves an issue where an Rx buffer can be reused prematurely with XDP redirect for igb. ====================
-
Lijun Pan authored
Tom wrote most of the driver code and his experience is valuable to us. Add him as a Reviewer so that patches will be Cc'ed and reviewed by him. Signed-off-by:
Lijun Pan <ljp@linux.ibm.com> Signed-off-by:
-
Mat Martineau authored
The join self tests previously used the '-c' command line option to enable creation of pcap files for the tests that run, but the change to allow running a subset of the join tests made overlapping use of that option. Restore the capture functionality with '-c' and move the syncookie test option to '-k'. Fixes: 1002b89f ("selftests: mptcp: add command line arguments for mptcp_join.sh") Acked-and-tested-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Ilya Lipnitskiy authored
A recent change to MIPS ralink reset logic made it so mt7530 actually resets the switch on platforms such as mt7621 (where bit 2 is the reset line for the switch). That exposed an issue where the switch would not function properly in TRGMII mode after a reset. Reconfigure core clock in TRGMII mode to fix the issue. Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled. Fixes: 3f9ef778 ("MIPS: ralink: manage low reset lines") Signed-off-by:
Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by:
-
Dan Carpenter authored
The MPTCP_PUSH_PENDING define is 6 and these tests should be testing if BIT(6) is set. Fixes: c2e6048f ("mptcp: fix race in release_cb") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Florian Fainelli authored
The PHY driver entry for BCM50160 and BCM50610M calls bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in order to configuration appropriate clock delays on the PHY, fix that. Fixes: 73333626 ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Dylan Hung authored
The interrupt handler may set the flag to reset the mac in the future, but that flag is not cleared once the reset has occurred. Fixes: 10cbd640 ("ftgmac100: Rework NAPI & interrupts handling") Signed-off-by:
Dylan Hung <dylan_hung@aspeedtech.com> Acked-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
-
Robert Hancock authored
The driver did not always clean up all allocated resources when probe failed. Fix the probe cleanup path to clean up everything that was allocated. Fixes: 57baf8cc ("net: axienet: Handle deferred probe on clock properly") Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Signed-off-by:
-
- 12 Mar, 2021 14 commits
-
-
liuyacan authored
The "backlog" argument in listen() specifies the maximom length of pending connections, so the accept queue should be considered full if there are exactly "backlog" elements. Signed-off-by:
liuyacan <yacanliu@163.com> Signed-off-by:
-
David S. Miller authored
This reverts commit 2055a99d. This change rejects legitimate configurations. A slave doesn't need to exist nor implement ndo_slave_setup. Signed-off-by:
-
Li RongQing authored
Igb needs a similar fix as commit 75aab4e1 ("i40e: avoid premature Rx buffer reuse") The page recycle code, incorrectly, relied on that a page fragment could not be freed inside xdp_do_redirect(). This assumption leads to that page fragments that are used by the stack/XDP redirect can be reused and overwritten. To avoid this, store the page count prior invoking xdp_do_redirect(). Longer explanation: Intel NICs have a recycle mechanism. The main idea is that a page is split into two parts. One part is owned by the driver, one part might be owned by someone else, such as the stack. t0: Page is allocated, and put on the Rx ring +--------------- used by NIC ->| upper buffer (rx_buffer) +--------------- | lower buffer +--------------- page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX t1: Buffer is received, and passed to the stack (e.g.) +--------------- | upper buff (skb) +--------------- used by NIC ->| lower buffer (rx_buffer) +--------------- page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX - 1 t2: Buffer is received, and redirected +--------------- | upper buff (skb) +--------------- used by NIC ->| lower buffer (rx_buffer) +--------------- Now, prior calling xdp_do_redirect(): page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX - 2 This means that buffer *cannot* be flipped/reused, because the skb is still using it. The problem arises when xdp_do_redirect() actually frees the segment. Then we get: page count == USHRT_MAX - 1 rx_buffer->pagecnt_bias == USHRT_MAX - 2 From a recycle perspective, the buffer can be flipped and reused, which means that the skb data area is passed to the Rx HW ring! To work around this, the page count is stored prior calling xdp_do_redirect(). Fixes: 9cbc948b ("igb: add XDP support") Signed-off-by:
Li RongQing <lirongqing@baidu.com> Reviewed-by:
Alexander Duyck <alexanderduyck@fb.com> Tested-by:
Vishakha Jambekar <vishakha.jambekar@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Maciej Fijalkowski authored
ixgbe_rx_offset(), that is supposed to initialize the Rx buffer headroom, relies on __IXGBE_RX_BUILD_SKB_ENABLED flag. Currently, the callsite of mentioned function is placed incorrectly within ixgbe_setup_rx_resources() where Rx ring's build skb flag is not set yet. This causes the XDP_REDIRECT to be partially broken due to inability to create xdp_frame in the headroom space, as the headroom is 0. Fix this by moving ixgbe_rx_offset() to ixgbe_configure_rx_ring() after the flag setting, which happens to be set in ixgbe_set_rx_buffer_len. Fixes: c0d4e9d2 ("ixgbe: store the result of ixgbe_rx_offset() onto ixgbe_ring") Signed-off-by:
Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by:
-
Maciej Fijalkowski authored
ice_rx_offset(), that is supposed to initialize the Rx buffer headroom, relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence. Currently, the callsite of mentioned function is placed incorrectly within ice_setup_rx_ring() where Rx ring's build skb flag is not set yet. This causes the XDP_REDIRECT to be partially broken due to inability to create xdp_frame in the headroom space, as the headroom is 0. Fix this by moving ice_rx_offset() to ice_setup_rx_ctx() after the flag setting. Fixes: f1b1f409 ("ice: store the result of ice_rx_offset() onto ice_ring") Signed-off-by:
Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by:
-
Maciej Fijalkowski authored
i40e_rx_offset(), that is supposed to initialize the Rx buffer headroom, relies on I40E_RXR_FLAGS_BUILD_SKB_ENABLED flag. Currently, the callsite of mentioned function is placed incorrectly within i40e_setup_rx_descriptors() where Rx ring's build skb flag is not set yet. This causes the XDP_REDIRECT to be partially broken due to inability to create xdp_frame in the headroom space, as the headroom is 0. For the record, below is the call graph: i40e_vsi_open i40e_vsi_setup_rx_resources i40e_setup_rx_descriptors i40e_rx_offset() <-- sets offset to 0 as build_skb flag is set below i40e_vsi_configure_rx i40e_configure_rx_ring set_ring_build_skb_enabled(ring) <-- set build_skb flag Fix this by moving i40e_rx_offset() to i40e_configure_rx_ring() after the flag setting. Fixes: f7bb0d71 ("i40e: store the result of i40e_rx_offset() onto i40e_ring") Reported-by:
Jesper Dangaard Brouer <brouer@redhat.com> Co-developed-by:
-
Magnus Karlsson authored
Fix the wrong napi work done reporting in the xsk path of the ice driver. The code in the main Rx processing loop was written to assume that the buffer allocation code returns true if all allocations where successful and false if not. In contrast with all other Intel NIC xsk drivers, the ice_alloc_rx_bufs_zc() has the inverted logic messing up the work done reporting in the napi loop. This can be fixed either by inverting the return value from ice_alloc_rx_bufs_zc() in the function that uses this in an incorrect way, or by changing the return value of ice_alloc_rx_bufs_zc(). We chose the latter as it makes all the xsk allocation functions for Intel NICs behave in the same way. My guess is that it was this unexpected discrepancy that gave rise to this bug in the first place. Fixes: 5bb0c4b5 ("ice, xsk: Move Rx allocation out of while-loop") Reported-by:
Magnus Karlsson <magnus.karlsson@intel.com> Tested-by:
-
David S. Miller authored
Maxim Mikityanskiy says: ==================== Bugfixes for HTB The HTB offload feature introduced a few bugs in HTB. One affects the non-offload mode, preventing attaching qdiscs to HTB classes, and the other affects the error flow, when the netdev doesn't support the offload, but it was requested. This short series fixes them. ==================== Acked-by:
Cong Wang <cong.wang@bytedance.com> Signed-off-by:
-
Maxim Mikityanskiy authored
htb_init may fail to do the offload if it's not supported or if a runtime error happens when allocating direct qdiscs. In those cases TC_HTB_CREATE command is not sent to the driver, however, htb_destroy gets called anyway and attempts to send TC_HTB_DESTROY. It shouldn't happen, because the driver didn't receive TC_HTB_CREATE, and also because the driver may not support ndo_setup_tc at all, while q->offload is true, and htb_destroy mistakenly thinks the offload is supported. Trying to call ndo_setup_tc in the latter case will lead to a NULL pointer dereference. This commit fixes the issues with htb_destroy by deferring assignment of q->offload until after the TC_HTB_CREATE command. The necessary cleanup of the offload entities is already done in htb_init. Reported-by: syzbot+b53a709f04722ca12a3c@syzkaller.appspotmail.com Fixes: d03b195b ("sch_htb: Hierarchical QoS hardware offload") Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
-
Maxim Mikityanskiy authored
htb_select_queue assumes it's always the offload mode, and it ends up in calling ndo_setup_tc without any checks. It may lead to a NULL pointer dereference if ndo_setup_tc is not implemented, or to an error returned from the driver, which will prevent attaching qdiscs to HTB classes in the non-offload mode. This commit fixes the bug by adding the missing check to htb_select_queue. In the non-offload mode it will return sch->dev_queue, mimicking tc_modify_qdisc's behavior for the case where select_queue is not implemented. Reported-by: syzbot+b53a709f04722ca12a3c@syzkaller.appspotmail.com Fixes: d03b195b ("sch_htb: Hierarchical QoS hardware offload") Signed-off-by:
-
Florian Fainelli authored
Per the datasheet, when we clear the power down bit, the PHY remains in an internal reset state for 40us and then resume normal operation. Account for that delay to avoid any issues in the future if genphy_resume() changes. Fixes: fe26821f ("net: phy: broadcom: Wire suspend/resume for BCM54810") Signed-off-by:
-
Tong Zhang authored
setup_fritz() in avmfritz.c might fail with -EIO and in this case the isac.type and isac.write_reg is not initialized and remains 0(NULL). A subsequent call to isac_release() will dereference isac->write_reg and crash. [ 1.737444] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 1.737809] #PF: supervisor instruction fetch in kernel mode [ 1.738106] #PF: error_code(0x0010) - not-present page [ 1.738378] PGD 0 P4D 0 [ 1.738515] Oops: 0010 [#1] SMP NOPTI [ 1.738711] CPU: 0 PID: 180 Comm: systemd-udevd Not tainted 5.12.0-rc2+ #78 [ 1.739077] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-p rebuilt.qemu.org 04/01/2014 [ 1.739664] RIP: 0010:0x0 [ 1.739807] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. [ 1.740200] RSP: 0018:ffffc9000027ba10 EFLAGS: 00010202 [ 1.740478] RAX: 0000000000000000 RBX: ffff888102f41840 RCX: 0000000000000027 [ 1.740853] RDX: 00000000000000ff RSI: 0000000000000020 RDI: ffff888102f41800 [ 1.741226] RBP: ffffc9000027ba20 R08: ffff88817bc18440 R09: ffffc9000027b808 [ 1.741600] R10: 0000000000000001 R11: 0000000000000001 R12: ffff888102f41840 [ 1.741976] R13: 00000000fffffffb R14: ffff888102f41800 R15: ffff8881008b0000 [ 1.742351] FS: 00007fda3a38a8c0(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 1.742774] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1.743076] CR2: ffffffffffffffd6 CR3: 00000001021ec000 CR4: 00000000000006f0 [ 1.743452] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1.743828] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1.744206] Call Trace: [ 1.744339] isac_release+0xcc/0xe0 [mISDNipac] [ 1.744582] fritzpci_probe.cold+0x282/0x739 [avmfritz] [ 1.744861] local_pci_probe+0x48/0x80 [ 1.745063] pci_device_probe+0x10f/0x1c0 [ 1.745278] really_probe+0xfb/0x420 [ 1.745471] driver_probe_device+0xe9/0x160 [ 1.745693] device_driver_attach+0x5d/0x70 [ 1.745917] __driver_attach+0x8f/0x150 [ 1.746123] ? device_driver_attach+0x70/0x70 [ 1.746354] bus_for_each_dev+0x7e/0xc0 [ 1.746560] driver_attach+0x1e/0x20 [ 1.746751] bus_add_driver+0x152/0x1f0 [ 1.746957] driver_register+0x74/0xd0 [ 1.747157] ? 0xffffffffc00d8000 [ 1.747334] __pci_register_driver+0x54/0x60 [ 1.747562] AVM_init+0x36/0x1000 [avmfritz] [ 1.747791] do_one_initcall+0x48/0x1d0 [ 1.747997] ? __cond_resched+0x19/0x30 [ 1.748206] ? kmem_cache_alloc_trace+0x390/0x440 [ 1.748458] ? do_init_module+0x28/0x250 [ 1.748669] do_init_module+0x62/0x250 [ 1.748870] load_module+0x23ee/0x26a0 [ 1.749073] __do_sys_finit_module+0xc2/0x120 [ 1.749307] ? __do_sys_finit_module+0xc2/0x120 [ 1.749549] __x64_sys_finit_module+0x1a/0x20 [ 1.749782] do_syscall_64+0x38/0x90 Signed-off-by:
-
Lv Yunlong authored
In qlcnic_83xx_get_minidump_template, fw_dump->tmpl_hdr was freed by vfree(). But unfortunately, it is used when extended is true. Fixes: 7061b2bd ("qlogic: Deletion of unnecessary checks before two function calls") Signed-off-by:
Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-03-11 This series contains updates to igc and e1000e drivers. Sasha adds locking to reset task to prevent race condition for igc. Muhammad fixes reporting of supported pause frame as well as advertised pause frame for Tx/Rx off for igc. Andre fixes timestamp retrieval from the wrong timer for igc. Vitaly adds locking to reset task to prevent race condition for e1000e. Dinghao Liu adds a missed check to return on error in e1000_set_d0_lplu_state_82571. ==================== Signed-off-by:
-
