rtw_hal_sreset_xmit_status_check() is a wrapper to call
rtl8188e_sreset_xmit_status_check(), which calls
rtl8188e_silentreset_for_specific_platform() in case of transmission has
stopped to do a silent reset and restore the transmission but
rtl8188e_silentreset_for_specific_platform() has empty defination,
so we can remove rtw_hal_sreset_xmit_status_check() because it doesn't
serve its purpose.
Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We can replace rtw_hal_sreset_reset_value() with rtw_hal_sreset_init() because
both function call sreset_reset_value() and sreset_init_value() respectively at
the end of code path, and function defination of sreset_reset_value() and
sreset_init_value() is identical.
Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

psrtpriv->silent_reset_inprogress is always false.
Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

silentreset_mutex initialized but not being used.
Signed-off-by: navin patidar <navin.patidar@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/rtl8192ee/btcoexist/halbtc8821a2ant.c:2491:3-4: Unneeded semicolon

 Removes unneeded semicolon.

Generated by: /kbuild/src/linux/scripts/coccinelle/misc/semicolon.cocci

CC: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Done as task 10 of the eudyptula challenge.
Signed-off-by: Nicolas Koch <nioko1337@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This prevents PHY not found types of errors for PHY drivers that are
probed after the Ethernet driver is probed, because the ifconfig UP is
done from userspace after all drivers have been probed.

Also avoid the cvmx-helper-board.c PHY code if a real PHY driver is
present, this allows a bootloader supplied device tree to specify the
PHY information rather than having to modify the code for each
different board.
Tested-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: devel@driverdev.osuosl.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgap_init_one() needs to handle error properly
if one of functions in dgap_init_one() is failed.

Introduce some functions for handling error in dgap_init_one()
 - dgap_tty_unregister() : unregister tty driver
 - dgap_free_flipbuf() : free flip buffer
 - dgap_release_remap() : release memory region and unmapped memory.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgap_firmware_load() has a lot of stuff which are
unrelated with loading firmware.
So just moved to dgap_init_one().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dgap_after_config_loaded() as function name doesn't tell
what it does.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dgap_free_irq() will free the irq which is requested in
dgap_request_irq().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It should be called after dgap_tty_register_ports() is failed.
So channels which are allocated in dgap_tty_init() will be freed.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firstminor in struct borad_t is always zero, so it
can be removed.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"remove" parameter is not used in dgap_parsefile().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- dgap_tty_uninit() doesn't match dgap_tty_init() at all.
so rename it. It is just used for cleanup when this module is
exited or failed to initialize by dgap_init_module.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pass "brd" to dgap_after_config_loaded() instead of passing
"dgap_numboards" and looking up brd again.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- Pass "dgap_numboards" to dgap_found_board() instead of
using a global variable.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgap_config_buf is only used in dgap_firmware_load().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- The dgap_tty_register_ports() needs to handle if the
tty_port_register_device() fails.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the kzalloc() fails for channels, it need to handle
that error. It should free channels which were already
allocated.

And also removes the call to dgap_tty_uninit() in
dgap_firmware_load().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- The channels array were set to NULL in dgap_found_board().
- Removes redundant null check for channels array in for loop,
if one of the channel cannot be allocated, dgap_tty_init() just returns
an error.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds a label for "kfree(brd)". And also remove
a state value as BOARD_FAILED in brd when dgap_do_remap() is failed.
Because "brd" will free after failure.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgap_probe1() function is just calling dgap_found_board().
So it is removed and dgap_found_board() is called directly.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removes confusing and unclear code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Converted a C99 comment to fix the following error:

ERROR: trailing statements should be on next line
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed open brace placement to address the following code-style errors:

ERROR: that open brace { should be on the previous line
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Converted some C99 warnings to fix the following error:

ERROR: trailing statements should be on next line
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rearranged statements around if and switch statements to address the following error:

ERROR: trailing statements should be on next line
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added spaces after ',' to fix the following warning:

ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed dead code from the file.
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ever since rtl8192u was added as a staging driver in v2.6.33 it contained
checks for CONFIG_IEEE80211_CRYPT_TKIP. But the Kconfig symbol
IEEE80211_CRYPT_TKIP was renamed to LIB80211_CRYPT_TKIP in v2.6.29. So
these checks have always evaluated to false. And these checks were rather
odd to begin with, since rtl8192u comes with its own ieee80211 stack,
which has support for TKIP built in.

Now the safe and easy thing to do here would be to remove these checks
and the code they hide. But it turns out that with some minor cleanup
the code currently hidden behind these checks builds cleanly. And by
building it we allow the people actually running this code to test
whether it is any good.

That minor cleanup is needed because ieee80211_encrypt_fragment()
accesses struct sk_buff's data member as if it is a struct
ieee80211_hdr. It's not. See, in ieee80211_xmit() a struct
ieee80211_hdr_3addrqos is skb_put() into the sk_buff with which
ieee80211_encrypt_fragment() will be called. So switch from
ieee80211_hdr to ieee80211_hdr_3addrqos here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added a space around '|' to address:

ERROR: need consistent spacing around '|' (ctx:VxW)
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To address the error -

ERROR: do not use C99 // comments

Removed all C99 comments.
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed dead code, commented out printks and DMESG.
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add staging board support for the KZM9D board and add
an emxx_udc platform device to allow in-tree continous
development of the driver on the KZM9D board.

When DT bindings are ready for the emxx_udc driver then
the platform device in the KZM9D staging board code can
easily be removed. Until then we use platform devices
to continously improve the driver and integration code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add staging board base support to allow continuous upstream
in-tree development and integration of platform devices.

Helps developers integrate devices as platform devices for
device drivers that only provide platform device bindings.
This in turn allows for incremental development of both
hardware feature support and DT binding work in parallel.

Two separate pieces of board staging functionality is
provided to ease per-board staging board support:
 - The board_staging() macro allows easy per-board callbacks
 - The board_staging_dt_node_available() provides DT node checking

Tested on the KZM9D board with the emxx_udc staging driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>