commit bb8175a8 ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.

So sometimes we get the following error on Marvell BG2Q DMP board:

[    1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[    1.569314] mmcblk0: retrying using single block read
[    1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[    1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[    1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[    1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3

This patches fixes this by adding the missing driver type setting.

Fixes: bb8175a8 ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The 250ms timeout is too short.

On my system enabling the oclk takes under 50ms and disabling slightly
over 100ms when idle. Under load disabling the clock can take over
350ms.

This does not make mmc clock gating look like good option to have on
sunxi but the system should not crash with mmc clock gating enabled
nonetheless.

This patch sets the timeout to 750ms.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

the current quirk set is for an old FPGA, and this patch corrects
quirks according to real SoC.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.

For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.

This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.

This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.

So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.

So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a required property "fsl,imx7d-usdhc" in binding doc.
Add an optional property "fsl,tuning-step" in binding doc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
	sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25

In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.

This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.

Fixes: 348487cb ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use more compact of_property_read_bool() calls instead of the
of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch fixes MMC not working issue on O2Micro/BayHub Host, which
requires transfer mode register to be cleared when sending no DMA
command.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When requesting a trim for several bytes, everything up to the next
erase-group is erased. This causes data corruption.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix the problem which timeout occurs at the time of command request with
several cards.

The timeout value was insufficient as a verification of several cards,
so it was changed 5 seconds from 2 seconds.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add an entry for Atmel SDMMC device.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.

dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.

We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.

This means that host should get DRTO and DTO interrupt.

But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.

There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

supports-highspeed was deprecated.
If someone use it, we need to notice information for it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

"blk_setting" doesn't use anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

When num-slots is lower than 1, it's right that should be returned -ENODEV.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.

Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.

So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a

[    4.991109] ------------[ cut here ]------------
[    4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[    4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM

because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.

Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
   "ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
   "min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.

On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.

In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.

Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.

What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Some Sandisk cards(such as "SDMB-32" and "SDM032" cards)
can't support CMD23, and would generate CMD timeout. So add
FIX-UP for these two types Sandisk cards.

Error log:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Before 5b83b223 the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16

Make this available only for built-in case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

See Documentation/DMA-API.txt - Part Id
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

adding SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,SDHCI_QUIRK2_PRESET_VALUE_BROKEN
flags for arasan sdhc.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>