This reverts commit 60293364.

Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.

The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly.  Most
of them use this to enable prefetching, which can only be done
for disk media.

But the commit being reverted here calls ->set_pio_mode() before
it's setup.  Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().

The set of drivers that depend upon the media type in their
->set_pio_method() are:

drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c

And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>

CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.

Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2

- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
  are corrupted, there are twiddled single bits 1->0 and some full 32-bit
  words corrupted, sometimes commands fail (which switches /dev/hda to
  PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
  corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.

This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 24df31ac.

The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 60293364) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.

This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 60293364).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 60293364.

Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf_event, powerpc: Fix compilation after big perf_counter rename

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vegard/kmemcheck:
  kmemcheck: add missing braces to do-while in kmemcheck_annotate_bitfield
  kmemcheck: update documentation
  kmemcheck: depend on HAVE_ARCH_KMEMCHECK
  kmemcheck: remove useless check
  kmemcheck: remove duplicated #include

* 'for-2.6.32' of git://linux-nfs.org/~bfields/linux: (68 commits)
  nfsd4: nfsv4 clients should cross mountpoints
  nfsd: revise 4.1 status documentation
  sunrpc/cache: avoid variable over-loading in cache_defer_req
  sunrpc/cache: use list_del_init for the list_head entries in cache_deferred_req
  nfsd: return success for non-NFS4 nfs4_state_start
  nfsd41: Refactor create_client()
  nfsd41: modify nfsd4.1 backchannel to use new xprt class
  nfsd41: Backchannel: Implement cb_recall over NFSv4.1
  nfsd41: Backchannel: cb_sequence callback
  nfsd41: Backchannel: Setup sequence information
  nfsd41: Backchannel: Server backchannel RPC wait queue
  nfsd41: Backchannel: Add sequence arguments to callback RPC arguments
  nfsd41: Backchannel: callback infrastructure
  nfsd4: use common rpc_cred for all callbacks
  nfsd4: allow nfs4 state startup to fail
  SUNRPC: Defer the auth_gss upcall when the RPC call is asynchronous
  nfsd4: fix null dereference creating nfsv4 callback client
  nfsd4: fix whitespace in NFSPROC4_CLNT_CB_NULL definition
  nfsd41: sunrpc: add new xprt class for nfsv4.1 backchannel
  sunrpc/cache: simplify cache_fresh_locked and cache_fresh_unlocked.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
  trivial: fix typo in aic7xxx comment
  trivial: fix comment typo in drivers/ata/pata_hpt37x.c
  trivial: typo in kernel-parameters.txt
  trivial: fix typo in tracing documentation
  trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
  trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
  trivial: remove unnecessary semicolons
  trivial: Fix duplicated word "options" in comment
  trivial: kbuild: remove extraneous blank line after declaration of usage()
  trivial: improve help text for mm debug config options
  trivial: doc: hpfall: accept disk device to unload as argument
  trivial: doc: hpfall: reduce risk that hpfall can do harm
  trivial: SubmittingPatches: Fix reference to renumbered step
  trivial: fix typos "man[ae]g?ment" -> "management"
  trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
  trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
  trivial: fix missing printk space in amd_k7_smp_check
  trivial: fix typo s/ketymap/keymap/ in comment
  trivial: fix typo "to to" in multiple files
  trivial: fix typos in comments s/DGBU/DBGU/
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Remove duplicate Kconfig entry
  HID: consolidate connect and disconnect into core code
  HID: fix non-atomic allocation in hid_input_report

Add a driver for the the Consumer IR (CIR) functionality of the Winbond
WPCD376I chipset (found on e.g. Intel DG45FC motherboards).
Signed-off-by: David Härdeman <david@hardeman.nu>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The shutdown method is used by the winbond cir driver to setup the
hardware for wake-from-S5.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt.  This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend.  Works for both suspend to ram
and hibernation.  The patch has zero effect on the running state.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This enabled power management functions for the SPI transport layer of the
lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.

[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Bit 0x80 in CTRL_REG3 is an ACTIVE_LOW rather than an ACTIVE_HIGH
function, I got that wrong during my last change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Enable the coretemp driver on an Intel Atom.

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add checks for Blackfin-specific issues that seem to crop up from time to
time.  In particular, we have helper macros to break a 32bit address into
the hi/lo parts, and we want to make sure people use the csync/ssync
variant that includes fun anomaly workarounds.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Limit our type matcher to the s/u/le/be etc sizes that actually exist to
prevent miss categorising s2 as a type.  Fix up the spelling of the error
also.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We should not recommend braces for the following:

    #define pr_fmt(fmt)    "%s: " fmt, __func__

allow things with double quotes round them to avoid this check.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Impact:
  - More verbose help/usage message.
  - Make the option -f an alias for --file.
  - On -h, --help, and --version display help message and exit(0).
  - With no FILE(s) given, exit(1) with "no input files".
  - On invalid options display help/usage and exit(1).

Based on a patch by Pavel Machek.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Ensure we terminate when there are no futher continuation lines when
trying to determine relative indent of conditionals and their blocks.
Reported-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the sanitation process in checkpatch.pl so that it blocks out
the text after a C99 style comment the same way it does with block style
comments.  This prevents the text from getting processed as regular code.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

An else cannot start a type, it would have to be within a block after the
else.  This can trigger false modifier matching.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add kerneldoc annotations for function formals of type struct flex_array
and gfp_t which are currently lacking.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

FLEX_ARRAY_INIT(element_size, total_nr_elements) cannot determine if
either parameter is valid, so flex arrays which are statically allocated
with this interface can easily become corrupted or reference beyond its
allocated memory.

This removes FLEX_ARRAY_INIT() as a struct flex_array initializer since no
initializer may perform the required checking.  Instead, the array is now
defined with a new interface:

	DEFINE_FLEX_ARRAY(name, element_size, total_nr_elements)

This may be prefixed with `static' for file scope.

This interface includes compile-time checking of the parameters to ensure
they are valid.  Since the validity of both element_size and
total_nr_elements depend on FLEX_ARRAY_BASE_SIZE and FLEX_ARRAY_PART_SIZE,
the kernel build will fail if either of these predefined values changes
such that the array parameters are no longer valid.

Since BUILD_BUG_ON() requires compile time constants, several of the
static inline functions that were once local to lib/flex_array.c had to be
moved to include/linux/flex_array.h.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a new function to the flex_array API:

	int flex_array_shrink(struct flex_array *fa)

This function will free all unused second-level pages.  Since elements are
now poisoned if they are not allocated with __GFP_ZERO, it's possible to
identify parts that consist solely of unused elements.

flex_array_shrink() returns the number of pages freed.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Newly initialized flex_array's and/or flex_array_part's are now poisoned
with a new poison value, FLEX_ARRAY_FREE.  It's value is similar to
POISON_FREE used in the various slab allocators, but is different to
distinguish between flex array's poisoned kmem and slab allocator poisoned
kmem.

This will allow us to identify flex_array_part's that only contain free
elements (and free them with an addition to the flex_array API).  This
could also be extended in the future to identify `get' uses on elements
that have not been `put'.

If __GFP_ZERO is passed for a part's gfp mask, the poisoning is avoided.
These elements are considered to be in-use since they have been
initialized.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a new function to the flex_array API:

	int flex_array_clear(struct flex_array *fa,
				unsigned int element_nr)

This function will zero the element at element_nr in the flex_array.

Although this is equivalent to using flex_array_put() and passing a
pointer to zero'd memory, flex_array_clear() does not require such a
pointer to memory that would most likely need to be allocated on the
caller's stack which could be significantly large depending on
element_size.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A couple of new uses of separate "P: name" "M: address" lines are
converted to single line "M: name <address>"
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Otherwise 'arch/arm/*omap*/foo.c' wouldn't match
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>