PMUv3p5 (which is mandatory with ARMv8.5) comes with some extra
features:

- All counters are 64bit

- The overflow point is controlled by the PMCR_EL0.LP bit

Add the required checks in the helpers that control counter
width and overflow, as well as the sysreg handling for the LP
bit. A new kvm_pmu_is_3p5() helper makes it easy to spot the
PMUv3p5 specific handling.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-14-maz@kernel.org

Allow userspace to write ID_DFR0_EL1, on the condition that only
the PerfMon field can be altered and be something that is compatible
with what was computed for the AArch64 view of the guest.
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-13-maz@kernel.org

Allow userspace to write ID_AA64DFR0_EL1, on the condition that only
the PMUver field can be altered and be at most the one that was
initially computed for the guest.
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-12-maz@kernel.org

As further patches will enable the selection of a PMU revision
from userspace, sample the supported PMU revision at VM creation
time, rather than building each time the ID_AA64DFR0_EL1 register
is accessed.

This shouldn't result in any change in behaviour.
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-11-maz@kernel.org

Even when using PMUv3p5 (which implies 64bit counters), there is
no way for AArch32 to write to the top 32 bits of the counters.
The only way to influence these bits (other than by counting
events) is by writing PMCR.P==1.

Make sure we obey the architecture and preserve the top 32 bits
on a counter update.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-10-maz@kernel.org

kvm_pmu_set_counter_value() is pretty odd, as it tries to update
the counter value while taking into account the value that is
currently held by the running perf counter.

This is not only complicated, this is quite wrong. Nowhere in
the architecture is it said that the counter would be offset
by something that is pending. The counter should be updated
with the value set by SW, and start counting from there if
required.

Remove the odd computation and just assign the provided value
after having released the perf event (which is then restarted).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-9-maz@kernel.org

In order to reduce the boilerplate code, add two helpers returning
the counter register index (resp. the event register) in the vcpu
register file from the counter index.
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-8-maz@kernel.org

The current PMU emulation sometimes narrows counters to 32bit
if the counter isn't the cycle counter. As this is going to
change with PMUv3p5 where the counters are all 64bit, fix
the couple of cases where this happens unconditionally.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20221113163832.3154370-7-maz@kernel.org

For 64bit counters that overflow on a 32bit boundary, make
sure we only check the bottom 32bit to generate a CHAIN event.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20221113163832.3154370-6-maz@kernel.org

The PMU architecture makes a subtle difference between a 64bit
counter and a counter that has a 64bit overflow. This is for example
the case of the cycle counter, which can generate an overflow on
a 32bit boundary if PMCR_EL0.LC==0 despite the accumulation being
done on 64 bits.

Use this distinction in the few cases where it matters in the code,
as we will reuse this with PMUv3p5 long counters.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-5-maz@kernel.org

Even when the underlying HW doesn't offer the CHAIN event
(which happens with QEMU), we can always support it as we're
in control of the counter overflow.

Always advertise the event via PMCEID0_EL0.
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-4-maz@kernel.org

Ricardo recently pointed out that the PMU chained counter emulation
in KVM wasn't quite behaving like the one on actual hardware, in
the sense that a chained counter would expose an overflow on
both halves of a chained counter, while KVM would only expose the
overflow on the top half.

The difference is subtle, but significant. What does the architecture
say (DDI0087 H.a):

- Up to PMUv3p4, all counters but the cycle counter are 32bit

- A 32bit counter that overflows generates a CHAIN event on the
  adjacent counter after exposing its own overflow status

- The CHAIN event is accounted if the counter is correctly
  configured (CHAIN event selected and counter enabled)

This all means that our current implementation (which uses 64bit
perf events) prevents us from emulating this overflow on the lower half.

How to fix this? By implementing the above, to the letter.

This largely results in code deletion, removing the notions of
"counter pair", "chained counters", and "canonical counter".
The code is further restructured to make the CHAIN handling similar
to SWINC, as the two are now extremely similar in behaviour.
Reported-by: Ricardo Koller <ricarkol@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20221113163832.3154370-3-maz@kernel.org

Align the ID_DFR0_EL1.PerfMon values with ID_AA64DFR0_EL1.PMUver.
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221113163832.3154370-2-maz@kernel.org

Pull fbdev fixes from Helge Deller:
 "A use-after-free bugfix in the smscufx driver and various minor error
  path fixes, smaller build fixes, sysfs fixes and typos in comments in
  the stifb, sisfb, da8xxfb, xilinxfb, sm501fb, gbefb and cyber2000fb
  drivers"

* tag 'fbdev-for-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  fbdev: cyber2000fb: fix missing pci_disable_device()
  fbdev: sisfb: use explicitly signed char
  fbdev: smscufx: Fix several use-after-free bugs
  fbdev: xilinxfb: Make xilinxfb_release() return void
  fbdev: sisfb: fix repeated word in comment
  fbdev: gbefb: Convert sysfs snprintf to sysfs_emit
  fbdev: sm501fb: Convert sysfs snprintf to sysfs_emit
  fbdev: stifb: Fall back to cfb_fillrect() on 32-bit HCRX cards
  fbdev: da8xx-fb: Fix error handling in .remove()
  fbdev: MIPS supports iomem addresses

Pull char/misc fixes from Greg KH:
 "Some small driver fixes for 6.1-rc3.  They include:

   - iio driver bugfixes

   - counter driver bugfixes

   - coresight bugfixes, including a revert and then a second fix to get
     it right.

  All of these have been in linux-next with no reported problems"

* tag 'char-misc-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  misc: sgi-gru: use explicitly signed char
  coresight: cti: Fix hang in cti_disable_hw()
  Revert "coresight: cti: Fix hang in cti_disable_hw()"
  counter: 104-quad-8: Fix race getting function mode and direction
  counter: microchip-tcb-capture: Handle Signal1 read and Synapse
  coresight: cti: Fix hang in cti_disable_hw()
  coresight: Fix possible deadlock with lock dependency
  counter: ti-ecap-capture: fix IS_ERR() vs NULL check
  counter: Reduce DEFINE_COUNTER_ARRAY_POLARITY() to defining counter_array
  iio: bmc150-accel-core: Fix unsafe buffer attributes
  iio: adxl367: Fix unsafe buffer attributes
  iio: adxl372: Fix unsafe buffer attributes
  iio: at91-sama5d2_adc: Fix unsafe buffer attributes
  iio: temperature: ltc2983: allocate iio channels once
  tools: iio: iio_utils: fix digit calculation
  iio: adc: stm32-adc: fix channel sampling time init
  iio: adc: mcp3911: mask out device ID in debug prints
  iio: adc: mcp3911: use correct id bits
  iio: adc: mcp3911: return proper error code on failure to allocate trigger
  iio: adc: mcp3911: fix sizeof() vs ARRAY_SIZE() bug
  ...

Pull USB fixes from Greg KH:
 "A few small USB fixes for 6.1-rc3. Include in here are:

   - MAINTAINERS update, including a big one for the USB gadget
     subsystem. Many thanks to Felipe for all of the years of hard work
     he has done on this codebase, it was greatly appreciated.

   - dwc3 driver fixes for reported problems.

   - xhci driver fixes for reported problems.

   - typec driver fixes for minor issues

   - uvc gadget driver change, and then revert as it wasn't relevant for
     6.1-final, as it is a new feature and people are still reviewing
     and modifying it.

  All of these have been in the linux-next tree with no reported issues"

* tag 'usb-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: gadget: Don't set IMI for no_interrupt
  usb: dwc3: gadget: Stop processing more requests on IMI
  Revert "usb: gadget: uvc: limit isoc_sg to super speed gadgets"
  xhci: Remove device endpoints from bandwidth list when freeing the device
  xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices
  xhci: Add quirk to reset host back to default state at shutdown
  usb: xhci: add XHCI_SPURIOUS_SUCCESS to ASM1042 despite being a V0.96 controller
  usb: dwc3: st: Rely on child's compatible instead of name
  usb: gadget: uvc: limit isoc_sg to super speed gadgets
  usb: bdc: change state when port disconnected
  usb: typec: ucsi: acpi: Implement resume callback
  usb: typec: ucsi: Check the connection on resume
  usb: gadget: aspeed: Fix probe regression
  usb: gadget: uvc: fix sg handling during video encode
  usb: gadget: uvc: fix sg handling in error case
  usb: gadget: uvc: fix dropped frame after missed isoc
  usb: dwc3: gadget: Don't delay End Transfer on delayed_status
  usb: dwc3: Don't switch OTG -> peripheral if extcon is present
  MAINTAINERS: Update maintainers for broadcom USB
  MAINTAINERS: move USB gadget and phy entries under the main USB entry

Pull gpio fixes from Bartosz Golaszewski:

 - convert gpio-tegra to using an immutable irqchip

 - MAINTAINERS update

* tag 'gpio-fixes-for-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: Change myself to a maintainer
  gpio: tegra: Convert to immutable irq chip

Pull perf fixes from Borislav Petkov:

 - Rename a perf memory level event define to denote it is of CXL type

 - Add Alder and Raptor Lakes support to RAPL

 - Make sure raw sample data is output with tracepoints

* tag 'perf_urgent_for_v6.1_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/mem: Rename PERF_MEM_LVLNUM_EXTN_MEM to PERF_MEM_LVLNUM_CXL
  perf/x86/rapl: Add support for Intel Raptor Lake
  perf/x86/rapl: Add support for Intel AlderLake-N
  perf: Fix missing raw data on tracepoint events

Merge tag 'loongarch-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch fixes from Huacai Chen:
 "Remove unused kernel stack padding, fix some build errors/warnings and
  two bugs in laptop platform driver"

* tag 'loongarch-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  platform/loongarch: laptop: Fix possible UAF and simplify generic_acpi_laptop_init()
  platform/loongarch: laptop: Adjust resume order for loongson_hotkey_resume()
  LoongArch: BPF: Avoid declare variables in switch-case
  LoongArch: Use flexible-array member instead of zero-length array
  LoongArch: Remove unused kernel stack padding

Pull cifs fixes from Steve French:

 - use after free fix for reconnect race

 - two memory leak fixes

* tag '6.1-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix use-after-free caused by invalid pointer `hostname`
  cifs: Fix pages leak when writedata alloc failed in cifs_write_from_iter()
  cifs: Fix pages array leak when writedata alloc failed in cifs_writedata_alloc()

Pull random number generator fix from Jason Donenfeld:
 "One fix from Jean-Philippe Brucker, addressing a regression in which
  early boot code on ARM64 would use the non-_early variant of the
  arch_get_random family of functions, resulting in the architectural
  random number generator appearing unavailable during that early phase
  of boot.

  The fix simply changes arch_get_random*() to arch_get_random*_early().

  This distinction between these two functions is a bit of an old wart
  I'm not a fan of, and for 6.2 I'll see if I can make obsolete the
  _early variant, so that one function does the right thing in all
  contexts without overhead"

* tag 'random-6.1-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: use arch_get_random*_early() in random_init()

Pull SCSI fixes from James Bottomley:
 "Varions small  fixes, all  in drivers.

  Some of these arrived during the merge window and got held over to
  make sure of testing on the -rc tree.

  The biggest change is for standards conformance in the target driver,
  closely followed by a set of bug fixes in megaraid_sas"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: ufs: core: Fix typo in comment
  scsi: mpi3mr: Select CONFIG_SCSI_SAS_ATTRS
  scsi: ufs: core: Fix typo for register name in comments
  scsi: pm80xx: Display proc_name in sysfs
  scsi: ufs: core: Fix the error log in ufshcd_query_flag_retry()
  scsi: ufs: core: Remove unneeded casts from void *
  scsi: lpfc: Fix spelling mistake "unsolicted" -> "unsolicited"
  scsi: qla2xxx: Use transport-defined speed mask for supported_speeds
  scsi: target: iblock: Fold iblock_emulate_read_cap_with_block_size() into iblock_get_blocks()
  scsi: qla2xxx: Fix serialization of DCBX TLV data request
  scsi: ufs: qcom: Remove redundant dev_err() call
  scsi: megaraid_sas: Move megasas_dbg_lvl init to megasas_init()
  scsi: megaraid_sas: Remove unnecessary memset()
  scsi: megaraid_sas: Simplify megasas_update_device_list
  scsi: megaraid_sas: Correct an error message
  scsi: megaraid_sas: Correct value passed to scsi_device_lookup()
  scsi: target: core: UA on all LUNs after reset
  scsi: target: core: New key must be used for moved PR
  scsi: target: core: Abort all preempted regs if requested
  scsi: target: core: Fix memory leak in preempt_and_abort
  ...

Pull block fixes from Jens Axboe:

 - NVMe pull request via Christoph:
      - make the multipath dma alignment match the non-multipath one
        (Keith Busch)
      - fix a bogus use of sg_init_marker() (Nam Cao)
      - fix circulr locking in nvme-tcp (Sagi Grimberg)

 - Initialization fix for requests allocated via the special hw queue
   allocator (John)

 - Fix for a regression added in this release with the batched
   completions of end_io backed requests (Ming)

 - Error handling leak fix for rbd (Yang)

 - Error handling leak fix for add_disk() failure (Yu)

* tag 'block-6.1-2022-10-28' of git://git.kernel.dk/linux:
  blk-mq: Properly init requests from blk_mq_alloc_request_hctx()
  blk-mq: don't add non-pt request with ->end_io to batch
  rbd: fix possible memory leak in rbd_sysfs_init()
  nvme-multipath: set queue dma alignment to 3
  nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
  nvme-tcp: replace sg_init_marker() with sg_init_table()
  block: fix memory leak for elevator on add_disk failure

Pull io_uring fix from Jens Axboe:
 "Just a fix for a locking regression introduced with the deferred
  task_work running from this merge window"

* tag 'io_uring-6.1-2022-10-28' of git://git.kernel.dk/linux:
  io_uring: unlock if __io_run_local_work locked inside
  io_uring: use io_run_local_work_locked helper

Pull misc hotfixes from Andrew Morton:
 "Eight fix pre-6.0 bugs and the remainder address issues which were
  introduced in the 6.1-rc merge cycle, or address issues which aren't
  considered sufficiently serious to warrant a -stable backport"

* tag 'mm-hotfixes-stable-2022-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (23 commits)
  mm: multi-gen LRU: move lru_gen_add_mm() out of IRQ-off region
  lib: maple_tree: remove unneeded initialization in mtree_range_walk()
  mmap: fix remap_file_pages() regression
  mm/shmem: ensure proper fallback if page faults
  mm/userfaultfd: replace kmap/kmap_atomic() with kmap_local_page()
  x86: fortify: kmsan: fix KMSAN fortify builds
  x86: asm: make sure __put_user_size() evaluates pointer once
  Kconfig.debug: disable CONFIG_FRAME_WARN for KMSAN by default
  x86/purgatory: disable KMSAN instrumentation
  mm: kmsan: export kmsan_copy_page_meta()
  mm: migrate: fix return value if all subpages of THPs are migrated successfully
  mm/uffd: fix vma check on userfault for wp
  mm: prep_compound_tail() clear page->private
  mm,madvise,hugetlb: fix unexpected data loss with MADV_DONTNEED on hugetlbfs
  mm/page_isolation: fix clang deadcode warning
  fs/ext4/super.c: remove unused `deprecated_msg'
  ipc/msg.c: fix percpu_counter use after free
  memory tier, sysfs: rename attribute "nodes" to "nodelist"
  MAINTAINERS: git://github.com -> https://github.com for nilfs2
  mm/kmemleak: prevent soft lockup in kmemleak_scan()'s object iteration loops
  ...

Pull powerpc fixes from Michael Ellerman:

 - Fix a case of rescheduling with user access unlocked, when preempt is
   enabled.

 - A follow-up fix for a recent fix, which could lead to IRQ state
   assertions firing incorrectly.

 - Two fixes for lockdep warnings seen when using kfence with the Hash
   MMU.

 - Two fixes for preempt warnings seen when using the Hash MMU.

 - Two fixes for the VAS coprocessor mechanism used on pseries.

 - Prevent building some of our older KVM backends when
   CONTEXT_TRACKING_USER is enabled, as it's known to cause crashes.

 - A couple of fixes for issues seen with PMU NMIs.

Thanks to Nicholas Piggin, Guenter Roeck, Frederic Barrat Haren Myneni,
Sachin Sant, and Samuel Holland.

* tag 'powerpc-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s/interrupt: Fix clear of PACA_IRQS_HARD_DIS when returning to soft-masked context
  powerpc/64s/interrupt: Perf NMI should not take normal exit path
  powerpc/64/interrupt: Prevent NMI PMI causing a dangerous warning
  KVM: PPC: BookS PR-KVM and BookE do not support context tracking
  powerpc: Fix reschedule bug in KUAP-unlocked user copy
  powerpc/64s: Fix hash__change_memory_range preemption warning
  powerpc/64s: Disable preemption in hash lazy mmu mode
  powerpc/64s: make linear_map_hash_lock a raw spinlock
  powerpc/64s: make HPTE lock and native_tlbie_lock irq-safe
  powerpc/64s: Add lockdep for HPTE lock
  powerpc/pseries: Use lparcfg to reconfig VAS windows for DLPAR CPU
  powerpc/pseries/vas: Add VAS IRQ primary handler

Currently the return value of 'sub_driver->init' is not checked. If
sparse_keymap_setup() called in the init function fails, 'generic_
inputdev' is freed, then it will lead a UAF when using it in generic_
acpi_laptop_init(). Fix it by checking the return value and setting
generic_inputdev to NULL after free, so as to avoid double free it.

The error code in generic_subdriver_init() is always negative, so the
return of generic_subdriver_init() can be simplified.

Fixes: 6246ed09 ("LoongArch: Add ACPI-based generic laptop driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Some laptops don't support SW_LID, but still have backlight control,
move backlight resuming before SW_LID event handling so as to avoid
backlight mistake due to early return.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Not all compilers support declare variables in switch-case, so move
declarations to the beginning of a function. Otherwise we may get such
build errors:

arch/loongarch/net/bpf_jit.c: In function ‘emit_atomic’:
arch/loongarch/net/bpf_jit.c:362:3: error: a label can only be part of a statement and a declaration is not a statement
   u8 r0 = regmap[BPF_REG_0];
   ^~
arch/loongarch/net/bpf_jit.c: In function ‘build_insn’:
arch/loongarch/net/bpf_jit.c:727:3: error: a label can only be part of a statement and a declaration is not a statement
   u8 t7 = -1;
   ^~
arch/loongarch/net/bpf_jit.c:778:3: error: a label can only be part of a statement and a declaration is not a statement
   int ret;
   ^~~
arch/loongarch/net/bpf_jit.c:779:3: error: expected expression before ‘u64’
   u64 func_addr;
   ^~~
arch/loongarch/net/bpf_jit.c:780:3: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
   bool func_addr_fixed;
   ^~~~
arch/loongarch/net/bpf_jit.c:784:11: error: ‘func_addr’ undeclared (first use in this function); did you mean ‘in_addr’?
          &func_addr, &func_addr_fixed);
           ^~~~~~~~~
           in_addr
arch/loongarch/net/bpf_jit.c:784:11: note: each undeclared identifier is reported only once for each function it appears in
arch/loongarch/net/bpf_jit.c:814:3: error: a label can only be part of a statement and a declaration is not a statement
   u64 imm64 = (u64)(insn + 1)->imm << 32 | (u32)insn->imm;
   ^~~
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Eliminate the following coccicheck warning:
./arch/loongarch/include/asm/ptrace.h:32:15-21: WARNING use flexible-array member instead
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Yushan Zhou <katrinzhou@tencent.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer making sense. Remove the padding for clarity.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>

Pull s390 fixes from Vasily Gorbik:

 - Remove outdated linux390 link from MAINTAINERS

 - Add few missing EX_TABLE entries to inline assemblies

 - Fix raw data collection for pai_ext PMU

 - Add kernel image secure boot trailer for future firmware versions

 - Fix out-of-bounds access on cio_ignore free

 - Fix memory allocation of mdev_types array in vfio-ap

* tag 's390-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vfio-ap: Fix memory allocation for mdev_types array
  s390/cio: fix out-of-bounds access on cio_ignore free
  s390/pai: fix raw data collection for PMU pai_ext
  s390/boot: add secure boot trailer
  s390/pci: add missing EX_TABLE entries to __pcistg_mio_inuser()/__pcilg_mio_inuser()
  s390/futex: add missing EX_TABLE entry to __futex_atomic_op()
  s390/uaccess: add missing EX_TABLE entries to __clear_user()
  MAINTAINERS: remove outdated linux390 link

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix for a build warning in the jump_label code

 - One of the git://github -> https://github cleanups, for the SiFive
   drivers

 - A fix for the kasan initialization code, this still likely warrants
   some cleanups but that's a bigger problem and at least this fixes the
   crashes in the short term

 - A pair of fixes for extension support detection on mixed LLVM/GNU
   toolchains

 - A fix for a runtime warning in the /proc/cpuinfo code

* tag 'riscv-for-linus-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Fix /proc/cpuinfo cpumask warning
  riscv: fix detection of toolchain Zihintpause support
  riscv: fix detection of toolchain Zicbom support
  riscv: mm: add missing memcpy in kasan_init
  MAINTAINERS: git://github.com -> https://github.com for sifive
  riscv: jump_label: mark arguments as const to satisfy asm constraints

Pull ACPI and device properties fixes from Rafael Wysocki:
 "These fix device properties documentation and the ACPI PCC code, add a
  new IRQ override quirk for resource handling and add one more item to
  the list of device IDs to be ignored when returned by _DEP.

  Specifics:

   - Fix the documentation of the *_match_string() family of functions
     to properly cover the return value (Andy Shevchenko)

   - Fix a possible integer overflow during multiplication in the ACPI
     PCC code (Manank Patel)

   - Make the ACPI device resources code skip IRQ override on Asus
     Vivobook S5602ZA (Tamim Khan)

   - Add LATT2021 to the list of device IDs that are ignored when
     returned by _DEP, because there are no drivers for them in the
     kernel and no plans to add such drivers (Hans de Goede)"

* tag 'acpi-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: scan: Add LATT2021 to acpi_ignore_dep_ids[]
  ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA
  ACPI: PCC: Fix unintentional integer overflow
  device property: Fix documentation for *_match_string() APIs

Pull power management fixes from Rafael Wysocki:
 "These make the intel_pstate driver work as expected on all hybrid
  platforms to date (regardless of possible platform firmware issues),
  fix hybrid sleep on systems using suspend-to-idle by default, make the
  generic power domains code handle disabled idle states properly and
  update pm-graph.

  Specifics:

   - Make intel_pstate use what is known about the hardware instead of
     relying on information from the platform firmware (ACPI CPPC in
     particular) to establish the relationship between the HWP CPU
     performance levels and frequencies on all hybrid platforms
     available to date (Rafael Wysocki)

   - Allow hybrid sleep to use suspend-to-idle as a system suspend
     method if it is the current suspend method of choice (Mario
     Limonciello)

   - Fix handling of unavailable/disabled idle states in the generic
     power domains code (Sudeep Holla)

   - Update the pm-graph suite of utilities to version 5.10 which is
     fixes-mostly and does not add any new features (Todd Brandt)"

* tag 'pm-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: domains: Fix handling of unavailable/disabled idle states
  pm-graph v5.10
  cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores
  cpufreq: intel_pstate: Read all MSRs on the target CPU
  PM: hibernate: Allow hybrid sleep to work with s2idle

While reworking the archrandom handling, commit d349ab99 ("random:
handle archrandom with multiple longs") switched to the non-early
archrandom helpers in random_init(), which broke initialization of the
entropy pool from the arm64 random generator.

Indeed at that point the arm64 CPU features, which verify that all CPUs
have compatible capabilities, are not finalized so arch_get_random_seed_longs()
is unsuccessful. Instead random_init() should use the _early functions,
which check only the boot CPU on arm64. On other architectures the
_early functions directly call the normal ones.

Fixes: d349ab99 ("random: handle archrandom with multiple longs")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>

lru_gen_add_mm() has been added within an IRQ-off region in the commit
mentioned below.  The other invocations of lru_gen_add_mm() are not within
an IRQ-off region.

The invocation within IRQ-off region is problematic on PREEMPT_RT because
the function is using a spin_lock_t which must not be used within
IRQ-disabled regions.

The other invocations of lru_gen_add_mm() occur while
task_struct::alloc_lock is acquired.  Move lru_gen_add_mm() after
interrupts are enabled and before task_unlock().

Link: https://lkml.kernel.org/r/20221026134830.711887-1-bigeasy@linutronix.de
Fixes: bd74fdae ("mm: multi-gen LRU: support page table walks")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Yu Zhao <yuzhao@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Before the do-while loop in mtree_range_walk(), the variables next, min,
max need to be initialized.  The variables last, prev_min and prev_max are
set within the loop body before they are eventually used after exiting the
loop body.

As it is a do-while loop, the loop body is executed at least once, so the
variables last, prev_min and prev_max do not need to be initialized before
the loop body.

Remove unneeded initialization of last and prev_min.

The needless initialization was reported by clang-analyzer as Dead Stores.

As the compiler already identifies these assignments as unneeded, it
optimizes the assignments away.  Hence:

No functional change. No change in object code.

Link: https://lkml.kernel.org/r/20221026120029.12555-2-lukas.bulwahn@gmail.comSigned-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

When using the VMA iterator, the final execution will set the variable
'next' to NULL which causes the function to fail out.  Restore the break
in the loop to exit the VMA iterator early without clearing NULL fixes the
issue.

Link: https://lore.kernel.org/lkml/29344.1666681759@jrobl/
Link: https://lkml.kernel.org/r/20221025161222.2634030-1-Liam.Howlett@oracle.com
Fixes: 763ecb03 (mm: remove the vma linked list)
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reported-by: "J. R. Okajima" <hooanon05g@gmail.com>
Tested-by: "J. R. Okajima" <hooanon05g@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>