The driver needs both CRC32 and CRC8 to link correctly:

ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe':
drivers/bluetooth/btnxpuart.c:1214: undefined reference to
`crc8_populate_msb'
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack':
drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'

Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds a driver based on serdev driver for the NXP BT serial protocol
based on running H:4, which can enable the built-in Bluetooth device
inside an NXP BT chip.

This driver has Power Save feature that will put the chip into sleep state
whenever there is no activity for 2000ms, and will be woken up when any
activity is to be initiated over UART.

This driver enables the power save feature by default by sending the vendor
specific commands to the chip during setup.

During setup, the driver checks if a FW is already running on the chip
by waiting for the bootloader signature, and downloads device specific FW
file into the chip over UART if bootloader signature is received..
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add binding document for NXP bluetooth chipsets attached over UART.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Adds serdev_device_break_ctl() and an implementation for ttyport.
This function simply calls the break_ctl in tty layer, which can
assert a break signal over UART-TX line, if the tty and the
underlying platform and UART peripheral supports this operation.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP
is not a standard error code. This will help maintain consistency in
error codes when new serdev API's are added.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

tty_set_termios() never returns anything else than 0. Make the debug
prints to look directly into the new termios instead to check CRTSCTS
state.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".

< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
      LE Read Transmit Power (0x08|0x004b) ncmd 1
        Status: Unknown HCI Command (0x01)

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.

It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.

Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined
  but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined
  but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined
  but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
  defined but not used [-Werror=unused-const-variable=]
  drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
  defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/bluetooth/btmrvl_sdio.c:43:34: error:
  ‘btmrvl_sdio_of_match_table’ defined but not used
  [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).

  drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
  but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This delays the identity address updates to give time for userspace to
process the new address otherwise there is a risk that userspace
creates a duplicated device if the MGMT event is delayed for some
reason.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This removes the following duplicate statement in
hci_le_ext_directed_advertising_sync():
cp.own_addr_type = own_addr_type;
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The msft_set_filter_enable() command was using the deprecated
hci_request mechanism rather than hci_sync. This caused the warning error:
hci0: HCI_REQ-0xfcf0
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Currently, when we initiate disconnection, we will wait for the peer's
reply unless when we are suspending, where we fire and forget the
disconnect request.

A similar case is when adapter is powering off. However, we still wait
for the peer's reply in this case. Therefore, if the peer is
unresponsive, the command will time out and the power off sequence
will fail, causing "bluetooth powered on by itself" to users.

This patch makes the host doesn't wait for the peer's reply when the
disconnection reason is powering off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Tested on Acer Nitro AN515-47 Notebook

output from /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e4 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Update the compatible for the Realtek RTL8821CS bluetooth node.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides
WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART
interface.

Note that the firmware this was tested with was firmware version
0x75b8f098.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add compatible string for RTL8821CS for existing Realtek Bluetooth
driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This bluetooth device is found in a combo WLAN/BT card
for a MediaTek 7663.

Tested on Acer Aspire A315-24P Notebook

The device information:

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3801 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes the following new warning:

net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing
error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This makes hci_conn_hash_add append to the tail of the conn_hash so it
matches the order they are created, this is required if the controller
attempts to match the order of ACL with CIS which uses append logic
when programming the CIS ids on the CIG.

The result of this change affects Create CIS:

Before:

< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
        Number of CIS: 2
        CIS Handle: 2560
        ACL Handle: 3586
        CIS Handle: 2561
        ACL Handle: 3585

After:

< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
        Number of CIS: 2
        CIS Handle: 2560
        ACL Handle: 3585
        CIS Handle: 2561
        ACL Handle: 3586
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support for RTL8852BS BT controller on UART interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add serdev support for the 88W8997 from NXP (previously Marvell). It
includes support for changing the baud rate. The command to change the
baud rate is taken from the user manual UM11483 Rev. 9 in section 7
(Bring-up of Bluetooth interfaces) from NXP.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Use the maybe_unused macro for the device tree ids instead of #ifdef
CONFIG_OF. This makes it easier to add support for new devices.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The 88W8997 bluetooth module supports setting the max-speed property.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Update the documentation with the device tree binding for the Marvell
88W8997 bluetooth device.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Remove hardcoded interface number check because Bluetooth specification
since version 4.0 only recommends and no longer requires specific
interface numbers.

While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain
required configuration table in Volume 4 - Host Controller Interface
Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2
changes the table from required to recommended configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This makes use of BIT macro when defining bitfields which makes it
clearer what bit it is toggling.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Pedro Tammela says:

====================
net/sched: act_pedit: minor improvements

This series aims to improve the code and usability of act_pedit for
netlink users.

Patches 1-2 improves error reporting for extended keys parsing with extack.

Patch 3 checks the static offsets a priori on create/update. Currently,
this is done at the datapath for both static and runtime offsets.

Patch 4 removes a check from the datapath which is redundant since the
netlink parsing validates the key types.

Patch 5 changes the 'pr_info()' calls in the datapath to rate limited
versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unbounded info messages in the pedit datapath can flood the printk
ring buffer quite easily depending on the action created.
As these messages are informational, usually printing some, not all,
is enough to bring attention to the real issue.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netlink parsing already validates the key 'htype'.
Remove the datapath check as it's redundant.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static key offsets should always be on 32 bit boundaries. Validate them on
create/update time for static offsets and move the datapath validation
for runtime offsets only.

iproute2 already errors out if a given offset and data size cannot be
packed to a 32 bit boundary. This change will make sure users which
create/update pedit instances directly via netlink also error out,
instead of finding out when packets are traversing.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have extack available when parsing 'ex' keys, so pass it to
tcf_pedit_keys_ex_parse and add more detailed error messages.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transform two checks in the 'ex' key parsing into netlink policies
removing extra if checks.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel will print several warnings in a short period of time
when it stalls. Like this:

First warning:
[ 7100.097547] ------------[ cut here ]------------
[ 7100.097550] NETDEV WATCHDOG: eno2 (xxx): transmit queue 8 timed out
[ 7100.097571] WARNING: CPU: 8 PID: 0 at net/sched/sch_generic.c:467
                       dev_watchdog+0x260/0x270
...

Second warning:
[ 7147.756952] rcu: INFO: rcu_preempt self-detected stall on CPU
[ 7147.756958] rcu:   24-....: (59999 ticks this GP) idle=546/1/0x400000000000000
                      softirq=367      3137/3673146 fqs=13844
[ 7147.756960]        (t=60001 jiffies g=4322709 q=133381)
[ 7147.756962] NMI backtrace for cpu 24
...

We calculate that the transmit queue start stall should occur before
7095s according to watchdog_timeo, the rcu start stall at 7087s.
These two times are close together, it is difficult to confirm which
happened first.

To let users know the exact time the stall started, print msecs when
the transmit queue time out.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Remove skb_mac_header() dependency in DSA xmit path

Eric started working on removing skb_mac_header() assumptions from the
networking xmit path, and I offered to help for DSA:
https://lore.kernel.org/netdev/20230321164519.1286357-1-edumazet@google.com/

The majority of this patch set is a straightforward replacement of
skb_mac_header() with skb->data (hidden either behind skb_eth_hdr(), or
behind skb_vlan_eth_hdr()). The only patch which is more "interesting"
is 9/9.

Another potential caller of __skb_vlan_pop() on xmit (and therefore
also of skb_mac_header()) is tcf_vlan_act(), but I haven't had the time
to investigate that (enough to submit changes other than what's here).

v1->v2:
- 09/09: document the vlan_tci argument of vlan_remove_tag() in the kdoc

v1 at:
https://lore.kernel.org/netdev/20230322233823.1806736-1-vladimir.oltean@nxp.com/

Cc: Madalin Bucur <madalin.bucur@nxp.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_xmit_get_vlan_info() calls __skb_vlan_pop() as the most
appropriate helper I could find which strips away a VLAN header.
That's all I need it to do, but __skb_vlan_pop() has more logic, which
will become incompatible with the future revert of commit 6d1ccff6
("net: reset mac header in dev_start_xmit()").

Namely, it performs a sanity check on skb_mac_header(), which will stop
being set after the above revert, so it will return an error instead of
removing the VLAN tag.

ocelot_xmit_get_vlan_info() gets called in 2 circumstances:

(1) the port is under a VLAN-aware bridge and the bridge sends
    VLAN-tagged packets

(2) the port is under a VLAN-aware bridge and somebody else (an 8021q
    upper) sends VLAN-tagged packets (using a VID that isn't in the
    bridge vlan tables)

In case (1), there is actually no bug to defend against, because
br_dev_xmit() calls skb_reset_mac_header() and things continue to work.

However, in case (2), illustrated using the commands below, it can be
seen that our intervention is needed, since __skb_vlan_pop() complains:

$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set $eth master br0 && ip link set $eth up
$ ip link add link $eth name $eth.100 type vlan id 100 && ip link set $eth.100 up
$ ip addr add 192.168.100.1/24 dev $eth.100

I could fend off the checks in __skb_vlan_pop() with some
skb_mac_header_was_set() calls, but seeing how few callers of
__skb_vlan_pop() there are from TX paths, that seems rather
unproductive.

As an alternative solution, extract the bare minimum logic to strip a
VLAN header, and move it to a new helper named vlan_remove_tag(), close
to the definition of vlan_insert_tag(). Document it appropriately and
make ocelot_xmit_get_vlan_info() call this smaller helper instead.

Seeing that it doesn't appear illegal to test skb->protocol in the TX
path, I guess it would be a good for vlan_remove_tag() to also absorb
the vlan_set_encap_proto() function call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>