- 06 Sep, 2013 14 commits
-
-
Seungwon Jeon authored
Implements to support GET and SET operations of the DME. These operations are used to configure the behavior of the UNIPRO. Along with basic operation, {Peer/AttrSetType} can be mixed. Signed-off-by:Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Tested-by:
Yaniv Gardi <ygardi@codeaurora.org> Signed-off-by:
Santosh Y <santoshsy@gmail.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Seungwon Jeon authored
IACTH(Interrupt aggregation counter threshold) value is allowed up to 0x1F and current setting value is the maximum. This value is related with NUTRS(max:0x20) of HCI's capability. Considering HCI controller doesn't support the maximum, IACTH setting should be adjusted with possible value. For that, existing 'ufshcd_config_int_aggr' is split into two part [reset, configure]. Signed-off-by:
-
Seungwon Jeon authored
Unlike 'GOOD' and 'CHECK CONDITION', other status values in Response UPIU may or may not contain sense data. That is returning sense data isn't obvious. So, in this case the Data Segment Length field should be checked. If a non-zero value, it means that UPIU has Sense Data in the Data Segment area. Signed-off-by:
-
adam radford authored
Signed-off-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
-
adam radford authored
Signed-off-by:
-
Greg Kroah-Hartman authored
Right now the Makefile for the mpt3sas driver does not even allow the driver to be built into the kernel. So fix that up, as there doesn't seem to be any obvious reason why this shouldn't be done. Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Sreekanth Reddy <Sreekanth.Reddy@lsi.com> Signed-off-by:
-
Brian King authored
This fixes an issue seen with devices getting marked offline in a scenario where a VIOS was getting rebooted while a client VFC adapter is in SCSI EH and prevents unnecessary EH escalation in some scenarios. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by:
-
Anton Blanchard authored
The hypervisor is big endian, so little endian kernel builds need to byteswap. [jejb: fix checkpatch errors] Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Bradley Grove authored
Reported-by:
Dave Jones <davej@redhat.com> Signed-off-by:
Bradley Grove <bgrove@attotech.com> Signed-off-by:
-
Bradley Grove authored
Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Bradley Grove authored
Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Bradley Grove authored
Reported-by:
-
Bradley Grove authored
Reported-by:
-
Bradley Grove authored
Reported-by:
-
- 03 Sep, 2013 26 commits
-
-
Vaughan Cao authored
Push file descriptor list locking down to per-device locking. Let sg_index_lock only protect device lookup. sdp->detached is also set and checked with this lock held. Signed-off-by:
Vaughan Cao <vaughan.cao@oracle.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Vaughan Cao authored
@detached is set under the protection of sg_index_lock. Without getting the lock, new sfp will be added during sg removal and there is no chance for it to be picked out. So check with sg_index_lock held in sg_add_sfp(). Signed-off-by:
-
Vaughan Cao authored
Open exclusive check is protected by o_sem, no need sg_open_exclusive_lock. @exclude is used to record which type of rwsem we are holding. Signed-off-by:
-
Vaughan Cao authored
A race condition may happen if two threads are both trying to open the same sg with O_EXCL simultaneously. It's possible that they both find fsds list is empty and get_exclude(sdp) returns 0, then they both call set_exclude() and break out from wait_event_interruptible and resume open. Now use rwsem to protect this process. Exclusive open gets write lock and others get read lock. The lock will be held until file descriptor is closed. This also leads 'exclude' only a status rather than a check mark. Signed-off-by:
-
Akinobu Mita authored
Commit b90ebc3d ("[SCSI] scsi_debug: fix logical block provisioning support") fixed several issues with logical block provisioning support, but it still doesn't properly fix the cases when unmap_alignment > 0. For example, load scsi_debug module with the following module parameters and make all blocks mapped by filling the storage with zero. # modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4 # dd if=/dev/zero of=$DEV Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS unexpectedly reports that the last UNMAP has done nothing. # sg_unmap --lba=1 --num=4 $DEV # sg_get_lba_status --lba=1 $DEV descriptor LBA: 0x0000000000000001 blocks: 16383 mapped The problem is in map_index_to_lba(), which should return the first LBA which is corresponding to a given index of provisioning map (map_storep). Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
"Martin K. Petersen" <martin.petersen@oracle.com> Acked-by:
-
Akinobu Mita authored
With module parameter num_parts > 0, partition table is built on the ramdisk storage when loading the driver. Unfortunately, there is an endianness bug in sdebug_build_parts(). So the partition table is not correctly initialized on big-endian systems. Signed-off-by:
Martin Peschke <mpeschke@linux.vnet.ibm.com> Acked-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Joe Carnuccio authored
At mailbox/buffer debug level, print the correct values of the outgoing and incoming mailbox registers. Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
On any Adapter when we flash through FC/FCoE without card reset option it still shows the Running FW version in Flashed FW version. This new interface will be used by API to instruct the driver to update its cache versions. Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Unless there is a need to observe them, the queue depth ramp up/down messages are a nuisance and may cause the system to become unresponsive so move it a non-default logging level. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Santosh Vernekar authored
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver. We now have to handle the aen so that other protocol drivers can use time extension during some loopback operations. Signed-off-by:
Santosh Vernekar <santosh.vernekar@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it Signed-off-by:
Armen Baloyan <armen.baloyan@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Joe Carnuccio authored
Add the missing FCP statistics to sysfs. Add reset FCP statistics functionality via sysfs. Signed-off-by:
-
Chad Dupuis authored
[SCSI] qla2xxx: Make log message that prints when a completion status requires a port down more readable. Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
Srinivasa Rao <srinivasa.rao@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Joe Carnuccio authored
For supported ISPS, Read asic temperature by calling the GET PARAMS (type C) mailbox command. Signed-off-by:
-
