Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
This patch adds misc4 match params which allows using a correct flex parser
that was programmed to the required protocol.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Remove MPLS specific fields from flex parser 3 layout.
Flex parser can be used for multiple protocols and should
not be hardcoded to a specific type.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Added the required definitions for supporting more protocols by flex parsers
(GTP-U, Geneve TLV options), and for using the right flex parser that was
configured for this protocol.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add error code to the error messages and removed duplicated message:
if termination table creation failed, we already get an error message
in mlx5_eswitch_termtbl_create, so no need for the additional error print
in the calling function.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

QP doorbell size is 16 bits.
Fixing sw steering's QP doorbel bitmask, which had 20 bits.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Rename the argument to better reflect that the meaning is
not number of records, but wheather or not we should
ring the dorbell.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Striding RQ attributes below are mutually dependent. An unaware
change to one might take the others out of the valid range derived
by the HW caps:
- The MPWQE size in bytes
- The number of strides in a MPWQE
- The stride size

Add checks to verify they are valid and comply to the HW spec
and SW assumptions/requirements.
This is not a fix, no particular issue exists today.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

If mlx5e_devlink_port_register() fails, driver may try to register
devlink health TX and RX reporters on non-registered devlink port.

Instead, create health reporters only if mlx5e_devlink_port_register()
does not fail. And destroy reporters only if devlink_port is registered.

Also, change mlx5e_get_devlink_port() behavior and return NULL in case
port is not registered to replicate devlink's wrapper when ndo is not
implemented.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The changes done in commit [1] were missed by the code movements
done in [2], as they were developed in ~parallel.
Here we re-apply them.

[1] commit e4484d9d ("net/mlx5e: Enable striding RQ for Connect-X IPsec capable devices")
[2] commit b3a131c2 ("net/mlx5e: Move params logic into its dedicated file")

Fixes: b3a131c2 ("net/mlx5e: Move params logic into its dedicated file")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

ETHTOOL_MSG_MODULE_EEPROM_GET is missing from the list of messages.
ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY is sadly a rather long name
so we need to adjust column length.

v2: use spaces (Andrew)

Fixes: c781ff12 ("ethtool: Allow network drivers to dump arbitrary EEPROM data")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido suggests we add a comment about the init of stats to -1.
This is unlikely to be clear to first time readers.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael suggest a few more stats we can expose.

$ ethtool -S eth0 --groups eth-mac
Standard stats for eth0:
eth-mac-FramesTransmittedOK: 902623288966
eth-mac-FramesReceivedOK: 28727667047
eth-mac-FrameCheckSequenceErrors: 1
eth-mac-AlignmentErrors: 0
eth-mac-OutOfRangeLengthField: 0
$ ethtool -S eth0 | grep '\(fcs\|align\|oor\)'
     rx_fcs_err_frames: 1
     rx_align_err_frames: 0
     tx_fcs_err_frames: 0
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Radu Pirea says:

====================
TJA1103 driver

This small series adds the TJA1103 PHY driver.

Changes in v3:
 - use phy_read_mmd_poll_timeout instead of spin_until_cond
 - changed the phy name from a generic one to something specific
 - minor indentation change

Changes in v2:
 - implemented genphy_c45_pma_suspend/genphy_c45_pma_suspend
 - set default internal delays set to 2ns(90 degrees)
 - added "VEND1_" prefix to the register definitions
 - disable rxid in case of txid
 - disable txid in case of rxid
 - disable internal delays in rgmii mode
 - reduced max line length to 80 characters
 - rebased on top of net-next/master
 - use genphy_c45_loopback as .set_loopback callback
 - renamed the driver from nxp-c45 to nxp-c45-tja11xx
 - used phy phy_set_bits_mmd/phy_clear_bits_mmd instead on phy_write_mmd where
 I had to set/clear one bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add driver for tja1103 driver and for future NXP C45 PHYs.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add generic PMA suspend and resume callback functions for C45 PHYs.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add PCI match for AC3X 98DX3265 device which is supported by the current
driver and firmware.
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On driver probe, kmemleak reported the following memory leak which was
due to allocated bitmap that was not being freed in stmmac_dvr_probe().

unreferenced object 0xffff9276014b13c0 (size 8):
  comm "systemd-udevd", pid 2143, jiffies 4294681112 (age 116.720s)
  hex dump (first 8 bytes):
    00 00 00 00 00 00 00 00                          ........
  backtrace:
    [<00000000c51e34b2>] stmmac_dvr_probe+0x1c0/0x440 [stmmac]
    [<00000000b530eb41>] intel_eth_pci_probe.cold+0x2b/0x14e [dwmac_intel]
    [<00000000b10f8929>] pci_device_probe+0xd2/0x150
    [<00000000fb254c74>] really_probe+0xf8/0x410
    [<0000000034128a59>] driver_probe_device+0x5d/0x150
    [<00000000016104d5>] device_driver_attach+0x53/0x60
    [<00000000cb18cd07>] __driver_attach+0x96/0x140
    [<00000000da9ffd5c>] bus_for_each_dev+0x7a/0xc0
    [<00000000af061a88>] bus_add_driver+0x184/0x1f0
    [<000000008be5c1c5>] driver_register+0x6c/0xc0
    [<0000000052b18a9e>] do_one_initcall+0x4d/0x210
    [<00000000154d4f07>] do_init_module+0x5c/0x230
    [<000000009b648d09>] load_module+0x2a5a/0x2d40
    [<000000000d86b76d>] __do_sys_finit_module+0xb5/0x120
    [<000000002b0cef95>] do_syscall_64+0x33/0x40
    [<0000000067b45bbb>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: bba2556e ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Bogendoerfer says:

====================
net: Korina improvements

While converting Mikrotik RB532 support to use device tree I stumbled
over the korina ethernet driver, which used way too many MIPS specific
hacks. This series cleans this all up and adds support for device tree.

Changes in v6:
 - remove korina from resource names and adapt DT binding to it
 - removed superfluous braces around of_get_mac_address

Changes in v5:
  - fixed email address in binding document, which prevented sending it

Changes in v4:
  - improve error returns in mdio_read further
  - added clock name and improved clk handling
  - fixed binding errors

Changes in v3:
  - use readl_poll_timeout_atomic in mdio_wait
  - return -ETIMEDOUT, if mdio_wait failed
  - added DT binding and changed name to idt,3243x-emac
  - fixed usage of of_get_mac_address for net-next

Changes in v2:
  - added device tree support to get rid of idt_cpu_freq
  - fixed compile test on 64bit archs
  - fixed descriptor current address handling by storing/using mapped
    dma addresses (dma controller modifies current address)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree bindings for ethernet controller integrated into
IDT 79RC3243x SoCs.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move structs/defines for ethernet/dma register into driver, since they
are only used for this driver and remove any MIPS specific includes.
This makes it possible to COMPILE_TEST the driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

With device tree clock is provided via CCF. For non device tree
use a maximum clock value to not overclock the PHY. The non device
tree usage will go away after platform is converted to DT.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there is no mac address passed via platform data try to get it via
device tree and fall back to a random mac address, if all fail.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of access to struct korina_device by just passing the mac
address via platform data and use drvdata for passing netdev to remove
function.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of messing with MIPS specific macros use DMA API for mapping
descriptors and skbs.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove helpers, which are only used in one call site.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Descriptors are mapped uncached so there is no need to do any cache
handling for them.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify probe/remove code by using devm_ functions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed MDIO functions to work reliable and not just by accident.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
mtk_ppe_offload fixes

A few incremental fixes for the initial flowtable offload support
and this driver:

1) Fix undefined reference to `dsa_port_from_netdev' due to missing
   dependencies in Kconfig, reported by Kbuild robot.

2) Missing mutex to serialize flow events via workqueue to the driver.

3) Handle FLOW_ACTION_VLAN_POP tag action.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not hit EOPNOTSUPP when flowtable offload provides a VLAN pop action.

Fixes: efce49df ("netfilter: flowtable: add vlan pop action offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch 2ed37183 ("netfilter: flowtable: separate replace, destroy and
stats to different workqueues") splits the workqueue per event type. Add
a mutex to serialize updates.

Fixes: 502e84e2 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Caused by:

 CONFIG_NET_DSA=m
 CONFIG_NET_MEDIATEK_SOC=y

mtk_ppe_offload.c:undefined reference to `dsa_port_from_netdev'

Fixes: 502e84e2 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next:

1) Add vlan match and pop actions to the flowtable offload,
   patches from wenxu.

2) Reduce size of the netns_ct structure, which itself is
   embedded in struct net Make netns_ct a read-mostly structure.
   Patches from Florian Westphal.

3) Add FLOW_OFFLOAD_XMIT_UNSPEC to skip dst check from garbage
   collector path, as required by the tc CT action. From Roi Dayan.

4) VLAN offload fixes for nftables: Allow for matching on both s-vlan
   and c-vlan selectors. Fix match of VLAN id due to incorrect
   byteorder. Add a new routine to properly populate flow dissector
   ethertypes.

5) Missing keys in ip{6}_route_me_harder() results in incorrect
   routes. This includes an update for selftest infra. Patches
   from Ido Schimmel.

6) Add counter hardware offload support through FLOW_CLS_STATS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Taking address of a function argument directly works just fine.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issue was traffic problems after a while with increased ping times if
flow offload is active. It turns out that key_offset with cookie is
needed in rhashtable_params but was re-assigned to head_offset.
Fix the assignment.

Fixes: 502e84e2 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: misc updates for -next

This series includes some misc updates for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SEPARATOR_VALUE macro is used as separator when getting
the register value, but the value of this macro is different
between pf and vf, it is a bit confusing for the user, so
synchronize the value of vf with pf.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify some inappropriate spaces in comments of struct
hlcgevf_tqp_stats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When enter suspend mode the counter of pf reset will be increased
twice, since both hclge_prepare_general() and hclge_prepare_wait()
increase this counter. So remove the duplicate counting in
hclge_prepare_general().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kernel test robot reports build errors in 3 Xilinx ethernet drivers.
They all use ioremap functions that are only available when HAS_IOMEM
is set/enabled. If it is not enabled, they all have build errors,
so make these 3 drivers depend on HAS_IOMEM.

ld: drivers/net/ethernet/xilinx/xilinx_emaclite.o: in function `xemaclite_of_probe':
xilinx_emaclite.c:(.text+0x9fc): undefined reference to `devm_ioremap_resource'

ld: drivers/net/ethernet/xilinx/xilinx_axienet_main.o: in function `axienet_probe':
xilinx_axienet_main.c:(.text+0x942): undefined reference to `devm_ioremap_resource'

ld: drivers/net/ethernet/xilinx/ll_temac_main.o: in function `temac_probe':
ll_temac_main.c:(.text+0x1283): undefined reference to `devm_platform_ioremap_resource_byname'
ld: ll_temac_main.c:(.text+0x13ad): undefined reference to `devm_of_iomap'
ld: ll_temac_main.c:(.text+0x162e): undefined reference to `devm_platform_ioremap_resource'

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Cc: Gary Guo <gary@garyguo.net>
Cc: Zhang Changzhong <zhangchangzhong@huawei.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: stable@vger.kernel.org
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>