- 15 Jul, 2015 40 commits
-
-
Dmitry Tunin authored
commit 692c062e upstream. BugLink: https://bugs.launchpad.net/bugs/1462614 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=06 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e076 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
J. Bruce Fields authored
commit 9fc2b4b4 upstream. Before calling into the filesystem, vfs_setxattr calls security_inode_setxattr, which ends up calling selinux_inode_setxattr in our case. That returns -EOPNOTSUPP whenever SBLABEL_MNT is not set. SBLABEL_MNT was supposed to be set by sb_finish_set_opts, which sets it only if selinux_is_sblabel_mnt returns true. The selinux_is_sblabel_mnt logic was broken by eadcabc6 "SELinux: do all flags twiddling in one place", which didn't take into the account the SECURITY_FS_USE_NATIVE behavior that had been introduced for nfs with eb9ae686 "SELinux: Add new labeling type native labels". This caused setxattr's of security labels over NFSv4.2 to fail. Cc: Eric Paris <eparis@redhat.com> Cc: David Quigley <dpquigl@davequigley.com> Reported-by: Richard Chan <rc556677@outlook.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> [PM: added the stable dependency] Signed-off-by: Paul Moore <pmoore@redhat.com> [ kamal: backport to 3.19-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Nicolas Boichat authored
commit 7ea3470a upstream. Prevents frequent panic on boot, if the irq handler rt5645_irq gets called before the workqueue rt5645_jack_detect_work is initialized. Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Frediano Ziglio authored
commit 8451cc96 upstream. If the function fails reference counter to the object is not decremented causing leaks. This is hard to spot as it happens only on very low memory situations. Signed-off-by: Frediano Ziglio <fziglio@redhat.com> Reviewed-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Frediano Ziglio authored
commit 2fa19535 upstream. If objects are moved back from system memory to VRAM (and spice id created again) memory is already initialized so we need to set flag to not clear memory. If you don't do it after a while using desktop many images turns to black or transparents. Signed-off-by: Frediano Ziglio <fziglio@redhat.com> Reviewed-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Peter Ujfalusi authored
commit 1cf0f448 upstream. SOC_DAPM_SINGLE("Playback AMP", ..) should not be under kcontrols. It causes kernel crash (NULL pointer) when the mixers are listed. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Peter Ujfalusi authored
commit 80ba2669 upstream. If the card is not part of any card the tas_data->codec is NULL since it is set only during snd_soc_codec_driver.probe, which is not yet called. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Eric W. Biederman authored
commit 8c6cf9cc upstream. Ignore an existing mount if the locked readonly, nodev or atime attributes are less permissive than the desired attributes of the new mount. On success ensure the new mount locks all of the same readonly, nodev and atime attributes as the old mount. The nosuid and noexec attributes are not checked here as this change is destined for stable and enforcing those attributes causes a regression in lxc and libvirt-lxc where those applications will not start and there are no known executables on sysfs or proc and no known way to create exectuables without code modifications Fixes: e51db735 ("userns: Better restrictions on when proc and sysfs can be mounted") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Ludovic Desroches authored
commit ea25525c upstream. Mci0 uses slot 0 not 1. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: 7a475267 ("ARM: at91: dt: add device tree file for SAMA5D4ek board") Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Omar Sandoval authored
commit 64ad6c48 upstream. Since commit bafc9b75 ("vfs: More precise tests in d_invalidate"), mounted subvolumes can be deleted because d_invalidate() won't fail. However, we run into problems when we attempt to delete the default subvolume while it is mounted as the root filesystem: # btrfs subvol list / ID 257 gen 306 top level 5 path rootvol ID 267 gen 334 top level 5 path snap1 # btrfs subvol get-default / ID 267 gen 334 top level 5 path snap1 # btrfs inspect-internal rootid / 267 # mount -o subvol=/ /dev/vda1 /mnt # btrfs subvol del /mnt/snap1 Delete subvolume (no-commit): '/mnt/snap1' ERROR: cannot delete '/mnt/snap1' - Operation not permitted # findmnt / findmnt: can't read /proc/mounts: No such file or directory # ls /proc # Markus reported that this same scenario simply led to a kernel oops. This happens because in btrfs_ioctl_snap_destroy(), we call d_invalidate() before we check may_destroy_subvol(), which means that we detach the submounts and drop the dentry before erroring out. Instead, we should only invalidate the dentry once the deletion has succeeded. Additionally, the shrink_dcache_sb() isn't necessary; d_invalidate() will prune the dcache for the deleted subvolume. Fixes: bafc9b75 ("vfs: More precise tests in d_invalidate") Reported-by: Markus Schauler <mschauler@gmail.com> Signed-off-by: Omar Sandoval <osandov@osandov.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Brian King authored
commit 45c44b5f upstream. Increase the default init stage change timeout from 15 seconds to 30 seconds. This resolves issues we have seen with some adapters not transitioning to the first init stage within 15 seconds, which results in adapter initialization failures. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Trond Myklebust authored
commit 88de6af2 upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9a ("nfs41: New backchannel helper routines") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Aaron Lu authored
commit 61e749d7 upstream. The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq desc's wake_depth unbalanced warning during system resume phase from the gpio_keys driver, which is the driver for the power button of the ASUS T100 laptop. Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Anton Blanchard authored
commit 72e349f1 upstream. When we take a PMU exception or a software event we call perf_read_regs(). This overloads regs->result with a boolean that describes if we should use the sampled instruction address register (SIAR) or the regs. If the exception is in kernel, we start with the kernel regs and backtrace through the kernel stack. At this point we switch to the userspace regs and backtrace the user stack with perf_callchain_user(). Unfortunately these regs have not got the perf_read_regs() treatment, so regs->result could be anything. If it is non zero, perf_instruction_pointer() decides to use the SIAR, and we get issues like this: 0.11% qemu-system-ppc [kernel.kallsyms] [k] _raw_spin_lock_irqsave | ---_raw_spin_lock_irqsave | |--52.35%-- 0 | | | |--46.39%-- __hrtimer_start_range_ns | | kvmppc_run_core | | kvmppc_vcpu_run_hv | | kvmppc_vcpu_run | | kvm_arch_vcpu_ioctl_run | | kvm_vcpu_ioctl | | do_vfs_ioctl | | sys_ioctl | | system_call | | | | | |--67.08%-- _raw_spin_lock_irqsave <--- hi mum | | | | | | | --100.00%-- 0x7e714 | | | 0x7e714 Notice the bogus _raw_spin_irqsave when we transition from kernel (system_call) to userspace (0x7e714). We inserted what was in the SIAR. Add a check in regs_use_siar() to check that the regs in question are from a PMU exception. With this fix the backtrace makes sense: 0.47% qemu-system-ppc [kernel.vmlinux] [k] _raw_spin_lock_irqsave | ---_raw_spin_lock_irqsave | |--53.83%-- 0 | | | |--44.73%-- hrtimer_try_to_cancel | | kvmppc_start_thread | | kvmppc_run_core | | kvmppc_vcpu_run_hv | | kvmppc_vcpu_run | | kvm_arch_vcpu_ioctl_run | | kvm_vcpu_ioctl | | do_vfs_ioctl | | sys_ioctl | | system_call | | __ioctl | | 0x7e714 | | 0x7e714 Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Dmitry Tunin authored
commit 4fa9dabc upstream. Lenovo G30-50 does not have a hardware wireless switch and wireless is always blocked. BugLink: https://bugs.launchpad.net/bugs/1397021Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Philippe Coval <philippe.coval@open.eurogiciel.org> [dvhart@linux.intel.com: Reordered dmi id per Phillippe's later version] Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Sumit.Saxena@avagotech.com authored
megaraid_sas : Modify return value of megasas_issue_blocked_cmd() and wait_and_poll() to consider command status returned by firmware commit 2be2a988 upstream. This patch is rebased on top of recently sent 18 patches(submitted by me) for megaraid_sas driver. Change the return value of wait_and_poll() and megsas_issue_blocked_cmd() based on MFI_STAT returned by firmware for that command. Earlier driver always send return type based on command completion (but never check MFI_STAT_OK for that command), so even if command is failed by firmware still driver will return SUCCESS status from these functions wait_and_poll() and megsas_issue_blocked_cmd() and if caller of these functions does not check command status (MFI_STAT), then it may endup using invalid data returned in DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to avoid this type of issue is do error handling and set proper return type from caller function wait_and_poll() and megsas_issue_blocked_cmd(). The change proposed in this patch will fix the regression introduced in patch- "90dc9d98 megaraid_sas : MFI MPT linked list corruption fix" inside function megasas_ld_list_query(). Prior to this MFI MPT linked list corruption fix patch, megasas_ld_list_query() function used to check DCMD status(returned by firmware) but with this linked list corruption fix patch, DCMD status will not be checked inside function megasas_ld_list_query() and introduced this issue of wrong data being used by function megasas_ld_list_query(). Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Olga Kornievskaia authored
commit e8d975e7 upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Malcolm Priestley authored
commit b5eeed8c upstream. There is a small chance that pRD->pRDInfo->skb could go NULL while the interrupt is processing. Put NULL check on loop to break out. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Robert Schlabbach authored
commit fb6d1f7d upstream. Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset. Dissolve the function hub_port_finish_reset() completely and divide the actions to be taken into those which need to be done after each reset attempt and those which need to be done after the full procedure is complete, and place them in the appropriate places in hub_port_reset(). Also, remove an unneeded forward declaration of hub_port_reset(). Verbose Problem Description: USB 3.0 devices may be "lost for good" during a hub port reset. This makes Linux unable to boot from USB 3.0 devices in certain constellations of host controllers and devices, because the USB device is lost during initialization, preventing the rootfs from being mounted. The underlying problem is that in the affected constellations, during the processing inside hub_port_reset(), the hub link state goes from 0 to SS.inactive after the initial reset, and back to 0 again only after the following "warm" reset. However, hub_port_finish_reset() is called after each reset attempt and sets the state the connected USB device based on the "preliminary" status of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when the following warm reset is complete and hub_port_finish_reset() is called again, its call to set the device to USB_STATE_DEFAULT is blocked by usb_set_device_state() which does not allow taking USB devices out of USB_STATE_NOTATTACHED state. Thanks to Alan Stern for guiding me to the proper solution and how to submit it. Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27Signed-off-by: Robert Schlabbach <robert_s@gmx.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Haggai Eran authored
commit cab46214 upstream. With an RTL8191SU USB adaptor, sometimes the hints for a fragmented packet are set, but the packet length is too large. Allocate enough space to prevent memory corruption and a resulting kernel panic [1]. [1] http://www.spinics.net/lists/linux-wireless/msg136546.htmlSigned-off-by: Haggai Eran <haggai.eran@gmail.com> ACKed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Yinghai Lu authored
commit 3a9ad0b4 upstream. David Ahern reported that d63e2e1f ("sparc/PCI: Clip bridge windows to fit in upstream windows") fails to boot on sparc/T5-8: pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000) The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA addresses, i.e., bus addresses returned via the DMA API (dma_map_single(), etc.), while the PCI core assumed dma_addr_t could hold *any* bus address, including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so they don't fit in a dma_addr_t. d63e2e1f added new checking that tripped over this mismatch. Add pci_bus_addr_t, which is wide enough to hold any PCI bus address, including both raw BAR values and DMA addresses. This will be 64 bits on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then dma_addr_t only needs to be wide enough to hold addresses from the DMA API. [bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at least as wide as dma_addr_t, documentation] Fixes: d63e2e1f ("sparc/PCI: Clip bridge windows to fit in upstream windows") Fixes: 23b13bc7 ("PCI: Fail safely if we can't handle BARs larger than 4GB") Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231Reported-by: David Ahern <david.ahern@oracle.com> Tested-by: David Ahern <david.ahern@oracle.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Joe Thornber authored
commit fb4100ae upstream. There is a race between a policy deciding to replace a cache entry, the core target writing back any dirty data from this block, and other IO threads doing IO to the same block. This sort of problem is avoided most of the time by the core target grabbing a bio prison cell before making the request to the policy. But for a demotion the core target doesn't know which block will be demoted, so can't do this in advance. Fix this demotion race by introducing a callback to the policy interface that allows the policy to grab the cell on behalf of the core target. Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Felipe Balbi authored
commit e18b7975 upstream. In case of non-Isochronous transfers, we don't want to clear DWC3_EP_BUSY flag until XferComplete event. That's because XferInProgress was only enabled so we can recycle TRBs and usb_requests quicker, but there are still other pending requests being transferred. In order to make sure we don't allow for another StartTransfer command while the HW is still processing other transfers, we must keep DWC3_EP_BUSY flag set and this what this patch does. Fixes: f3af3651 (usb: dwc3: gadget: always enable IOC on bulk/interrupt transfers) Reported-by: sundeep subbaraya <sundeep.lkml@gmail.com> Tested-by: sundeep subbaraya <sundeep.lkml@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Richard Fitzgerald authored
commit 15575ed5 upstream. The Arizona codec drivers had an incorrect dB scaling for the noise generator gain that started at 0dB and went upwards. Actually the highest setting is 0dB. Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Paul E. McKenney authored
commit 6e91f8cb upstream. If, at the time __rcu_process_callbacks() is invoked, there are callbacks in Tiny RCU's callback list, but none of them are ready to be invoked, the current list-management code will knit the non-ready callbacks out of the list. This can result in hangs and possibly worse. This commit therefore inserts a check for there being no callbacks that can be invoked immediately. This bug is unlikely to occur -- you have to get a new callback between the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to __rcu_process_callbacks(). It was detected by the addition of RCU-bh testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's mutation testing. Although this bug was made much more likely by 915e8a4f (rcu: Remove fastpath from __rcu_process_callbacks()), this did not cause the bug, but rather made it much more probable. That said, it takes more than 40 hours of rcutorture testing, on average, for this bug to appear, so this fix cannot be considered an emergency. Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Alex Deucher authored
commit 39fa10f7 upstream. Since we are messing with state in the worker. v2: drop the changes in the mst worker Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Vincent Fann authored
commit 1277fa2a upstream. Several of these drivers have there TX randomly blocked for 3~5 seconds while measuring tx throughput (iperf). The root couse happens in rtl_pci_flush(). The function uses a while-loop to wait for TX queue length to decrease to 0. The TX queue length counts the number of packets that are queued in the driver. The driver relys on the TX OK interrupt to return skb and reduce TX queue length. The interrupt subroutine disables interupts, reads the interrupt registers, and then clears the registers in the beginning of _rtl_pci_interrupt(). After all interupts process are finished, the driver invokes enable_interrupt() to enable interupts. This behavior is normal for an interrupt subroutine. But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in unterminated while-loop. This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior. Signed-off-by: Vincent Fann <vincent_fann@realtek.com> Signed-off-by: Shao Fu <shaofu@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Gregory CLEMENT authored
commit ce2f6ea1 upstream. The commit df59fa7f "spi: orion: support armada extended baud rates" was too optimistic for the maximum baud rate that the Armada SoCs can support. According to the hardware datasheet the maximum frequency supported by the Armada 370 SoC is tclk/4. But for the Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and for the Armada 375 it is tclk/15. Currently the armada-370-spi compatible is only used by the Armada 370 and the Armada XP device tree. On Armada 370, tclk cannot be higher than 200MHz. In order to be able to handle both SoCs, we can take the minimum of 50MHz and tclk/4. A proper solution is adding a compatible string for each SoC, but it can't be done as a fix for compatibility reason (we can't modify device tree that have been already released) and it will be part of a separate patch. Fixes: df59fa7f (spi: orion: support armada extended baud rates) Reported-by: Kostya Porotchkin <kostap@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Nicolas Ferre authored
commit 8687634b upstream. In RS485 mode, we may want to set the delay_rts_after_send value to 0. In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but this is exactly the expected behavior if we want no delay... Moreover, if the value was set to non-zero value by device-tree or earlier ioctl command, it was impossible to change it back to zero. Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ kamal: backport to 3.19-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
David Fries authored
commit f7134eea upstream. A temperature conversion can take 750 ms and when possible the w1_therm slave driver drops the bus_mutex to allow other bus operations, but that includes operations such as a periodic slave search, which can remove this slave when it is no longer detected. If that happens the sl->family_data will be freed and set to NULL causing w1_slave_show to crash when it wakes up. Signed-off-by: David Fries <David@Fries.net> Reported-By: Thorsten Bschorr <thorsten@bschorr.de> Tested-by: Thorsten Bschorr <thorsten@bschorr.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Tomas Winkler authored
commit fe292283 upstream. HW has to be in known state before the initialisation sequence is started. The polling step for settling aliveness was set to 200ms while in practise this can be done in up to 30msecs. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Barak Yoresh <barak.yoresh@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Rafael J. Wysocki authored
commit 08249651 upstream. Refine the mechanism introduced by commit f244d8b6 ("ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the ignore_hotplug setting of the device to its parent bridge in case hotplug notifications related to the graphics adapter switching are given for the bridge rather than for the device itself (they need to be ignored in both cases). Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927 Fixes: b440bde7 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Reported-and-tested-by: tiagdtd-lava <tiagdtd-lava@yahoo.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Mimi Zohar authored
commit f2b3dee4 upstream. The call to asymmetric_key_hex_to_key_id() from ca_keys_setup() silently fails with -ENOMEM. Instead of dynamically allocating memory from a __setup function, this patch defines a variable and calls __asymmetric_key_hex_to_key_id(), a new helper function, directly. This bug was introduced by 'commit 46963b77 ("KEYS: Overhaul key identification when searching for asymmetric keys")'. Changelog: - for clarification, rename hexlen to asciihexlen in asymmetric_key_hex_to_key_id() - add size argument to __asymmetric_key_hex_to_key_id() - David Howells - inline __asymmetric_key_hex_to_key_id() - David Howells - remove duplicate strlen() calls Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Mimi Zohar authored
commit cd025f7f upstream. Include don't appraise or measure rules for the NSFS filesystem in the builtin ima_tcb and ima_appraise_tcb policies. Changelog: - Update documentation Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Roberto Sassu authored
commit 6438de9f upstream. This patch adds a rule in the default measurement policy to skip inodes in the cgroupfs filesystem. Measurements for this filesystem can be avoided, as all the digests collected have the same value of the digest of an empty file. Furthermore, this patch updates the documentation of IMA policies in Documentation/ABI/testing/ima_policy to make it consistent with the policies set in security/integrity/ima/ima_policy.c. Signed-off-by: Roberto Sassu <rsassu@suse.de> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Paolo Bonzini authored
commit 69a12200 upstream. The argument to KVM_GET_DIRTY_LOG is a memslot id; it may not match the position in the memslots array, which is sorted by gfn. Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Bart Van Assche authored
commit a44074f1 upstream. Although it is possible to let SRP I/O continue if a reconnect results in a reduction of the number of channels, the current code does not handle this scenario correctly. Instead of making the reconnect code more complex, consider this as a reconnection failure. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Bart Van Assche authored
commit c014c8cd upstream. Reception of a DREQ message only causes the state of a single channel to change. Hence move the 'connected' member variable from the target to the channel data structure. This patch avoids that following false positive warning can be reported by srp_destroy_qp(): WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]() Call Trace: [<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0 [<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp] [<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp] [<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp] [<ffffffff81346f60>] dev_attr_store+0x20/0x30 [<ffffffff811dd90f>] sysfs_write_file+0xef/0x170 [<ffffffff8116d248>] vfs_write+0xc8/0x190 [<ffffffff8116d411>] sys_write+0x51/0x90 Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Bart Van Assche authored
commit 8de9fe3a upstream. Avoid that receiving a DREQ while RDMA channels are being established causes target->qp_in_error to be reset. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Bart Van Assche authored
commit fb49c8bb upstream. Fix a scsi_get_host() / scsi_host_put() imbalance in the error path of srp_create_target(). See also patch "IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning" (commit ID 34aa654e). Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-