- 23 Feb, 2017 40 commits
-
-
Chen-Yu Tsai authored
commit 919ab252 upstream. The musb driver calls into this phy driver to disable/enable squelch detection. This function was introduced in 24fe86a6 ("phy: sun4i-usb: Add a sunxi specific function for setting squelch-detect"). This function in turn calls sun4i_usb_phy_write, which uses a mutex to guard the common access register. Unfortunately musb does this in atomic context, which results in the following warning with lock debugging enabled: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97 in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: kworker/0:2 CPU: 0 PID: 96 Comm: kworker/0:2 Not tainted 4.8.0-rc4-00181-gd502f8ad1c3e #13 Hardware name: Allwinner sun8i Family Workqueue: events musb_deassert_reset [<c010bc01>] (unwind_backtrace) from [<c0109237>] (show_stack+0xb/0xc) [<c0109237>] (show_stack) from [<c02a669b>] (dump_stack+0x67/0x74) [<c02a669b>] (dump_stack) from [<c05d68c9>] (mutex_lock+0x15/0x2c) [<c05d68c9>] (mutex_lock) from [<c02c3589>] (sun4i_usb_phy_write+0x39/0xec) [<c02c3589>] (sun4i_usb_phy_write) from [<c03e6327>] (musb_port_reset+0xfb/0x184) [<c03e6327>] (musb_port_reset) from [<c03e4917>] (musb_deassert_reset+0x1f/0x2c) [<c03e4917>] (musb_deassert_reset) from [<c012ecb5>] (process_one_work+0x129/0x2b8) [<c012ecb5>] (process_one_work) from [<c012f5e3>] (worker_thread+0xf3/0x424) [<c012f5e3>] (worker_thread) from [<c0132dbd>] (kthread+0xa1/0xb8) [<c0132dbd>] (kthread) from [<c0105f31>] (ret_from_fork+0x11/0x20) Since the register access is mmio, we can use a spinlock to guard this specific access, rather than the mutex that guards the entire phy. Fixes: ba4bdc9e ("PHY: sunxi: Add driver for sunxi usb phy") Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Robert Jarzmik authored
commit ca26475b upstream. The commit 9bf448c6 ("ARM: pxa: use generic gpio operation instead of gpio register") from Oct 17, 2011, leads to the following static checker warning: arch/arm/mach-pxa/spitz_pm.c:172 spitz_charger_wakeup() warn: double left shift '!gpio_get_value(SPITZ_GPIO_KEY_INT) << (1 << ((SPITZ_GPIO_KEY_INT) & 31))' As Dan reported, the value is shifted three times : - once by gpio_get_value(), which returns either 0 or BIT(gpio) - once by the shift operation '<<' - a last time by GPIO_bit(gpio) which is BIT(gpio) Therefore the calculation lead to a chained or operator of : - (1 << gpio) << (1 << gpio) = (2^gpio)^gpio = 2 ^ (gpio * gpio) It is be sheer luck the former statement works, only because each gpio used is strictly smaller than 6, and therefore 2^(gpio^2) never overflows a 32 bits value, and because it is used as a boolean value to check a gpio activation. As the xxx_charger_wakeup() functions are used as a true/false detection mechanism, take that opportunity to change their prototypes from integer return value to boolean one. Fixes: 9bf448c6 ("ARM: pxa: use generic gpio operation instead of gpio register") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Joe Perches <joe@perches.com> Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Eric Dumazet authored
commit e895cdce upstream. In commit f02db315 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data") Francesco added IP_TOS values specified as integer. However, kernel sends to userspace (at recvmsg() time) an IP_TOS value in a single byte, when IP_RECVTOS is set on the socket. It can be very useful to reflect all ancillary options as given by the kernel in a subsequent sendmsg(), instead of aborting the sendmsg() with EINVAL after Francesco patch. So this patch extends IP_TOS ancillary to accept an u8, so that an UDP server can simply reuse same ancillary block without having to mangle it. Jesper can then augment https://github.com/netoptimizer/network-testing/blob/master/src/udp_example02.c to add TOS reflection ;) Fixes: f02db315 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Francesco Fusco <ffusco@redhat.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Andrew Bresticker authored
commit d771fdf9 upstream. The ramoops buffer may be mapped as either I/O memory or uncached memory. On ARM64, this results in a device-type (strongly-ordered) mapping. Since unnaligned accesses to device-type memory will generate an alignment fault (regardless of whether or not strict alignment checking is enabled), it is not safe to use memcpy(). memcpy_fromio() is guaranteed to only use aligned accesses, so use that instead. Signed-off-by:
Andrew Bresticker <abrestic@chromium.org> Signed-off-by:
Enric Balletbo Serra <enric.balletbo@collabora.com> Reviewed-by:
Puneet Kumar <puneetster@chromium.org> Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Furquan Shaikh authored
commit 7e75678d upstream. persistent_ram_update uses vmap / iomap based on whether the buffer is in memory region or reserved region. However, both map it as non-cacheable memory. For armv8 specifically, non-cacheable mapping requests use a memory type that has to be accessed aligned to the request size. memcpy() doesn't guarantee that. Signed-off-by:
Furquan Shaikh <furquan@google.com> Signed-off-by:
Aaron Durbin <adurbin@chromium.org> Reviewed-by:
Olof Johansson <olofj@chromium.org> Tested-by:
Furquan Shaikh <furquan@chromium.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit d5a9bf0b upstream. I have here a FPGA behind PCIe which exports SRAM which I use for pstore. Now it seems that the FPGA no longer supports cmpxchg based updates and writes back 0xff…ff and returns the same. This leads to crash during crash rendering pstore useless. Since I doubt that there is much benefit from using cmpxchg() here, I am dropping this atomic access and use the spinlock based version. Cc: Anton Vorontsov <anton@enomsg.org> Cc: Colin Cross <ccross@android.com> Cc: Kees Cook <keescook@chromium.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Rabin Vincent <rabinv@axis.com> Tested-by:
Rabin Vincent <rabinv@axis.com> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> [kees: remove "_locked" suffix since it's the only option now] Signed-off-by:
-
Daeho Jeong authored
commit 93e3b4e6 upstream. Now, ext4_do_update_inode() clears high 16-bit fields of uid/gid of deleted and evicted inode to fix up interoperability with old kernels. However, it checks only i_dtime of an inode to determine whether the inode was deleted and evicted, and this is very risky, because i_dtime can be used for the pointer maintaining orphan inode list, too. We need to further check whether the i_dtime is being used for the orphan inode list even if the i_dtime is not NULL. We found that high 16-bit fields of uid/gid of inode are unintentionally and permanently cleared when the inode truncation is just triggered, but not finished, and the inode metadata, whose high uid/gid bits are cleared, is written on disk, and the sudden power-off follows that in order. Signed-off-by:
Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by:
Hobin Woo <hobin.woo@samsung.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 24b923f0 upstream. This device uses GPIOs: 28 to switch between analog and digital modes: on digital mode, it should be set to 1. The code that sets it on analog mode is OK, but it misses the logic that sets it on digital mode. Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 1871d718 upstream. The cx231xx_set_agc_analog_digital_mux_select() callers expect it to return 0 or an error. Returning a positive value makes the first attempt to switch between analog/digital to fail. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 505a0ea7 upstream. With the current settings, only one channel locks properly. That's likely because, when this driver was written, Brazil were still using experimental transmissions. Change it to reproduce the settings used by the newer drivers. That makes it lock on other channels. Tested with both PixelView SBTVD Hybrid (cx231xx-based) and C3Tech Digital Duo HDTV/SDTV (em28xx-based) devices. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit dafb65fb upstream. On this frontend, it takes a while to start output normal TS data. That only happens on state S9. On S8, the TS output is enabled, but it is not reliable enough. However, the zigzag loop is too fast to let it sync. As, on practical tests, the zigzag software loop doesn't seem to be helping, but just slowing down the tuning, let's switch to hardware algorithm, as the tuners used on such devices are capable of work with frequency drifts without any help from software. Signed-off-by:
-
David Hsu authored
commit 0733424c upstream. Exported pwm channels aren't removed before the pwmchip and are leaked. This results in invalid sysfs files. This fix removes all exported pwm channels before chip removal. Signed-off-by:
David Hsu <davidhsu@google.com> Fixes: 76abbdde ("pwm: Add sysfs interface") Signed-off-by:
Thierry Reding <thierry.reding@gmail.com> Signed-off-by:
-
Larry Finger authored
commit 0c9d3491 upstream. Some RTL8821AE devices sold in Great Britain have the country code of 0x25 encoded in their EEPROM. This value is not tested in the routine that establishes the regulatory info for the chip. The fix is to set this code to have the same capabilities as the EU countries. In addition, the channels allowed for COUNTRY_CODE_ETSI were more properly suited for China and Israel, not the EU. This problem has also been fixed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Shao Fu authored
commit 02b5fffb upstream. Driver rtlwifi maintains its own regulatory information, The Chrome Autotest (https://www.chromium.org/chromium-os/testing/autotest-user-doc) showed some errors. This patch adds the necessary information for rtlwifi. Signed-off-by:
Shao Fu <shaofu@realtek.com> Signed-off-by:
-
Sebastian Frias authored
commit ee26c013 upstream. Without this patch irq_domain_disassociate() cannot properly release the interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed' but said bit is never cleared, only set. Commit 088f40b7 ("genirq: Generic chip: Add linear irq domain support") added irq_map_generic_chip() function and also stated "This lacks a removal function for now". This commit provides an implementation of an unmap function that can be called by irq_domain_disassociate(). [ tglx: Made the function static and removed the export as we have neither a prototype nor a modular user. ] Fixes: 088f40b7 ("genirq: Generic chip: Add linear irq domain support") Signed-off-by:
Sebastian Frias <sf84@laposte.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Mason <slash.tmp@free.fr> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> [bwh: Backported to 3.16: open-code irq_domain_get_irq_data(), irq_domain_set_info()] Signed-off-by:
-
Chen-Yu Tsai authored
commit 071133a2 upstream. The value for the second channel in _ENUM_DOUBLE (double channel) MUXs is not correctly updated, due to using the wrong bit shift. Use the correct bit shift, so both channels toggle together. Fixes: 3727b496 (ASoC: dapm: Consolidate MUXs and value MUXs) Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit 432746f8 upstream. When we call symbol__fixup_duplicate() we use algorithms to pick the "best" symbols for cases where there are various functions/aliases to an address, and those check zero size symbols, which, before calling symbol__fixup_end() are _all_ symbols in a just parsed kallsyms file. So first fixup the end, then fixup the duplicates. Found while trying to figure out why 'perf test vmlinux' failed, see the output of 'perf test -v vmlinux' to see cases where the symbols picked as best for vmlinux don't match the ones picked for kallsyms. Cc: Anton Blanchard <anton@samba.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 694bf407 ("perf symbols: Add some heuristics for choosing the best duplicate symbol") Link: http://lkml.kernel.org/n/tip-rxqvdgr0mqjdxee0kf8i2ufn@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Will Deacon authored
commit 3a402a70 upstream. When TIF_SINGLESTEP is set for a task, the single-step state machine is enabled and we must take care not to reset it to the active-not-pending state if it is already in the active-pending state. Unfortunately, that's exactly what user_enable_single_step does, by unconditionally setting the SS bit in the SPSR for the current task. This causes failures in the GDB testsuite, where GDB ends up missing expected step traps if the instruction being stepped generates another trap, e.g. PTRACE_EVENT_FORK from an SVC instruction. This patch fixes the problem by preserving the current state of the stepping state machine when TIF_SINGLESTEP is set on the current thread. Reported-by:
Yao Qi <yao.qi@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Sergei Shtylyov authored
commit e330b9a6 upstream. of_irq_get[_byname]() return 0 iff irq_create_of_mapping() call fails. Returning both error code and 0 on failure is a sign of a misdesigned API, it makes the failure check unnecessarily complex and error prone. We should rely on the platform IRQ resource in this case, not return 0, especially as 0 can be a valid IRQ resource too... Fixes: aff008ad ("platform_get_irq: Revert to platform_get_resource if of_irq_get fails") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Jan Viktorin authored
commit 4d31a258 upstream. The variable i contains a total number of resources (including IORESOURCE_IRQ). However, we want the dmem_region_start to point after the last resource of type IORESOURCE_MEM. The original behaviour leads (very likely) to skipping several UIO mapping regions and makes them useless. Fix this by computing dmem_region_start from the uiomem which points to the last used UIO mapping. Fixes: 0a0c3b5a ("Add new uio device for dynamic memory allocation") Signed-off-by:
Jan Viktorin <viktorin@rehivetech.com> Signed-off-by:
-
Florian Westphal authored
commit 95a8d19f upstream. In case nf_conntrack_tuple_taken did not find a conflicting entry check that all entries in this hash slot were tested and restart in case an entry was moved to another chain. Reported-by:
Florian Westphal <fw@strlen.de> Acked-by:
Pablo Neira Ayuso <pablo@netfilter.org> [bwh: Backported to 3.16: - Adjust context - Use NF_CT_STAT_INC(), not the _ATOMIC variant, since we disable BHs] Signed-off-by:
-
Florian Fainelli authored
commit 9a0a5c4c upstream. Since we keep shadow copies of which interrupt sources are enabled through the intrl2_*_mask_{set,clear} macros, make sure that the ordering in which we do these two operations: update the copy, then unmask the register is correct. This is not currently a problem because we actually do not use them, but we will in a subsequent patch optimizing register accesses, so better be safe here. Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Maik Broemme authored
commit 8e2e0317 upstream. Similar to the AR93xx and the AR94xx series, the AR95xx also have the same quirk for the Bus Reset. It will lead to instant system reset if the device is assigned via VFIO to a KVM VM. I've been able reproduce this behavior with a MikroTik R11e-2HnD. Fixes: c3e59ee4 ("PCI: Mark Atheros AR93xx to avoid bus reset") Signed-off-by:
Maik Broemme <mbroemme@libmpq.org> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 72b4f6a5 upstream. On x86_32, when an interrupt happens from kernel space, SS and SP aren't pushed and the existing stack is used. So pt_regs is effectively two words shorter, and the previous stack pointer is normally the memory after the shortened pt_regs, aka '®s->sp'. But in the rare case where the interrupt hits right after the stack pointer has been changed to point to an empty stack, like for example when call_on_stack() is used, the address immediately after the shortened pt_regs is no longer on the stack. In that case, instead of '®s->sp', the previous stack pointer should be retrieved from the beginning of the current stack page. kernel_stack_pointer() wants to do that, but it forgets to dereference the pointer. So instead of returning a pointer to the previous stack, it returns a pointer to the beginning of the current stack. Note that it's probably outside of kernel_stack_pointer()'s scope to be switching stacks at all. The x86_64 version of this function doesn't do it, and it would be better for the caller to do it if necessary. But that's a patch for another day. This just fixes the original intent. Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Byungchul Park <byungchul.park@lge.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nilay Vaish <nilayvaish@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 0788aa6a ("x86: Prepare removal of previous_esp from i386 thread_info structure") Link: http://lkml.kernel.org/r/472453d6e9f6a2d4ab16aaed4935f43117111566.1471535549.git.jpoimboe@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Geert Uytterhoeven authored
commit 2cf9a578 upstream. clk-divider uses clk_readl()/clk_writel() everywhere, except in clk_divider_round_rate(), where plain readl() is used. Change this to clk_readl(), as it makes a difference on powerpc. Fixes: e6d5e7d9 ("clk-divider: Fix READ_ONLY when divider > 1") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Steffen Maier authored
commit aceeffbb upstream. This was lost with commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") but is necessary for problem determination, e.g. to see the currently active zone set during automatic port scan. For the large GPN_FT response (4 pages), save space by not dumping any empty residual entries. Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") Reviewed-by:
Alexey Ishchuk <aishchuk@linux.vnet.ibm.com> Reviewed-by:
Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Steffen Maier authored
commit 94db3725 upstream. commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") started to add FC_CT_HDR_LEN which made zfcp dump random data out of bounds for RSPN GS responses because u.rspn.rsp is the largest and last field in the union of struct zfcp_fc_req. Other request/response types only happened to stay within bounds due to the padding of the union or due to the trace capping of u.gspn.rsp to ZFCP_DBF_SAN_MAX_PAYLOAD. Timestamp : ... Area : SAN Subarea : 00 Level : 1 Exception : - CPU id : .. Caller : ... Record id : 2 Tag : fsscth2 Request id : 0x... Destination ID : 0x00fffffc Payload short : 01000000 fc020000 80020000 00000000 xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx <=== 00000000 00000000 00000000 00000000 Payload length : 32 <=== struct zfcp_fc_req { [0] struct zfcp_fsf_ct_els ct_els; [56] struct scatterlist sg_req; [96] struct scatterlist sg_rsp; union { struct {req; rsp;} adisc; SIZE: 28+28= 56 struct {req; rsp;} gid_pn; SIZE: 24+20= 44 struct {rspsg; req;} gpn_ft; SIZE: 40*4+20=180 struct {req; rsp;} gspn; SIZE: 20+273= 293 struct {req; rsp;} rspn; SIZE: 277+16= 293 [136] } u; } SIZE: 432 Signed-off-by:
-
Steffen Maier authored
commit 771bf035 upstream. With commit 2c55b750 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") we lost the N_Port-ID where an ELS response comes from. With commit 7c7dc196 ("[SCSI] zfcp: Simplify handling of ct and els requests") we lost the N_Port-ID where a CT response comes from. It's especially useful if the request SAN trace record with D_ID was already lost due to trace buffer wrap. GS uses an open WKA port handle and ELS just a D_ID, and only for ELS we could get D_ID from QTCB bottom via zfcp_fsf_req. To cover both cases, add a new field to zfcp_fsf_ct_els and fill it in on request to use in SAN response trace. Strictly speaking the D_ID on SAN response is the FC frame's S_ID. We don't need a field for the other end which is always us. Signed-off-by:
-
Steffen Maier authored
commit 7c964ffe upstream. This information was lost with commit a54ca0f6 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") but is required to debug e.g. invalid handle situations. Signed-off-by:
-
Steffen Maier authored
commit d27a7cb9 upstream. Since commit a54ca0f6 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") HBA records no longer contain WWPN, D_ID, or LUN to reduce duplicate information which is already in REC records. In contrast to "regular" target ports, we don't use recovery to open WKA ports such as directory/nameserver, so we don't get REC records. Therefore, introduce pseudo REC running records without any actual recovery action but including D_ID of WKA port on open/close. Signed-off-by:
-
Steffen Maier authored
commit 0102a30a upstream. bring back commit d21e9daa ("[SCSI] zfcp: Dont use 0 to indicate invalid LUN in rec trace") which was lost with commit ae0904f6 ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.") Signed-off-by:
-
Steffen Maier authored
commit 35f040df upstream. While retaining the actual filtering according to trace level, the following commits started to write such filtered records with a hardcoded record level of 1 instead of the actual record level: commit 250a1352 ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.") commit a54ca0f6 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") Now we can distinguish written records again for offline level filtering. Signed-off-by:
-
Steffen Maier authored
commit 4eeaa4f3 upstream. On a successful end of reopen port forced, zfcp_erp_strategy_followup_success() re-uses the port erp_action and the subsequent zfcp_erp_action_cleanup() now sees ZFCP_ERP_SUCCEEDED with erp_action->action==ZFCP_ERP_ACTION_REOPEN_PORT instead of ZFCP_ERP_ACTION_REOPEN_PORT_FORCED but must not perform zfcp_scsi_schedule_rport_register(). We can detect this because the fresh port reopen erp_action is in its very first step ZFCP_ERP_STEP_UNINITIALIZED. Otherwise this opens a time window with unblocked rport (until the followup port reopen recovery would block it again). If a scsi_cmnd timeout occurs during this time window fc_timed_out() cannot work as desired and such command would indeed time out and trigger scsi_eh. This prevents a clean and timely path failover. This should not happen if the path issue can be recovered on FC transport layer such as path issues involving RSCNs. Also, unnecessary and repeated DID_IMM_RETRY for pending and undesired new requests occur because internally zfcp still has its zfcp_port blocked. As follow-on errors with scsi_eh, it can cause, in the worst case, permanently lost paths due to one of: sd <scsidev>: [<scsidisk>] Medium access timeout failure. Offlining disk! sd <scsidev>: Device offlined - not ready after error recovery For fix validation and to aid future debugging with other recoveries we now also trace (un)blocking of rports. Signed-off-by:
-
Steffen Maier authored
commit 70369f8e upstream. In the hardware data router case, introduced with kernel 3.2 commit 86a9668a ("[SCSI] zfcp: support for hardware data router") the ELS/GS request&response length needs to be initialized as in the chained SBAL case. Otherwise, the FCP channel rejects ELS requests with FSF_REQUEST_SIZE_TOO_LARGE. Such ELS requests can be issued by user space through BSG / HBA API, or zfcp itself uses ADISC ELS for remote port link test on RSCN. The latter can cause a short path outage due to unnecessary remote target port recovery because the always failing ADISC cannot detect extremely short path interruptions beyond the local FCP channel. Below example is decoded with zfcpdbf from s390-tools: Timestamp : ... Area : SAN Subarea : 00 Level : 1 Exception : - CPU id : .. Caller : zfcp_dbf_san_req+0408 Record id : 1 Tag : fssels1 Request id : 0x<reqid> Destination ID : 0x00<target d_id> Payload info : 52000000 00000000 <our wwpn > [ADISC] <our wwnn > 00<s_id> 00000000 00000000 00000000 00000000 00000000 Timestamp : ... Area : HBA Subarea : 00 Level : 1 Exception : - CPU id : .. Caller : zfcp_dbf_hba_fsf_res+0740 Record id : 1 Tag : fs_ferr Request id : 0x<reqid> Request status : 0x00000010 FSF cmnd : 0x0000000b [FSF_QTCB_SEND_ELS] FSF sequence no: 0x... FSF issued : ... FSF stat : 0x00000061 [FSF_REQUEST_SIZE_TOO_LARGE] FSF stat qual : 00000000 00000000 00000000 00000000 Prot stat : 0x00000100 Prot stat qual : 00000000 00000000 00000000 00000000 Signed-off-by:
-
Steffen Maier authored
commit bd77befa upstream. For an NPIV-enabled FCP device, zfcp can erroneously show "NPort (fabric via point-to-point)" instead of "NPIV VPORT" for the port_type sysfs attribute of the corresponding fc_host. s390-tools that can be affected are dbginfo.sh and ziomon. zfcp_fsf_exchange_config_evaluate() ignores fsf_qtcb_bottom_config.connection_features indicating NPIV and only sets fc_host_port_type to FC_PORTTYPE_NPORT if fsf_qtcb_bottom_config.fc_topology is FSF_TOPO_FABRIC. Only the independent zfcp_fsf_exchange_port_evaluate() evaluates connection_features to overwrite fc_host_port_type to FC_PORTTYPE_NPIV in case of NPIV. Code was introduced with upstream kernel 2.6.30 commit 0282985d ("[SCSI] zfcp: Report fc_host_port_type as NPIV"). This works during FCP device recovery (such as set online) because it performs FSF_QTCB_EXCHANGE_CONFIG_DATA followed by FSF_QTCB_EXCHANGE_PORT_DATA in sequence. However, the zfcp-specific scsi host sysfs attributes "requests", "megabytes", or "seconds_active" trigger only zfcp_fsf_exchange_config_evaluate() resetting fc_host port_type to FC_PORTTYPE_NPORT despite NPIV. The zfcp-specific scsi host sysfs attribute "utilization" triggers only zfcp_fsf_exchange_port_evaluate() correcting the fc_host port_type again in case of NPIV. Evaluate fsf_qtcb_bottom_config.connection_features in zfcp_fsf_exchange_config_evaluate() where it belongs to. Signed-off-by:
-
Max Staudt authored
commit d50b3f43 upstream. When using efifb with a 16-bit (5:6:5) visual, fbcon's text is rendered in the wrong colors - e.g. text gray (#aaaaaa) is rendered as green (#50bc50) and neighboring pixels have slightly different values (such as #50bc78). The reason is that fbcon loads its 16 color palette through efifb_setcolreg(), which in turn calculates a 32-bit value to write into memory for each palette index. Until now, this code could only handle 8-bit visuals and didn't mask overlapping values when ORing them. With this patch, fbcon displays the correct colors when a qemu VM is booted in 16-bit mode (in GRUB: "set gfxpayload=800x600x16"). Fixes: 7c83172b ("x86_64 EFI boot support: EFI frame buffer driver") # v2.6.24+ Signed-off-by:
Max Staudt <mstaudt@suse.de> Acked-By:
Peter Jones <pjones@redhat.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Lyude authored
commit 9504a892 upstream. While VGA hotplugging worked(ish) before, it looks like that was mainly because we'd unintentionally enable it in valleyview_crt_detect_hotplug() when we did a force trigger. This doesn't work reliably enough because whenever the display powerwell on vlv gets disabled, the values set in VLV_ADPA get cleared and consequently VGA hotplugging gets disabled. This causes bugs such as one we found on an Intel NUC, where doing the following sequence of hotplugs: - Disconnect all monitors - Connect VGA - Disconnect VGA - Connect HDMI Would result in VGA hotplugging becoming disabled, due to the powerwells getting toggled in the process of connecting HDMI. Changes since v3: - Expose intel_crt_reset() through intel_drv.h and call that in vlv_display_power_well_init() instead of encoder->base.funcs->reset(&encoder->base); Changes since v2: - Use intel_encoder structs instead of drm_encoder structs Changes since v1: - Instead of handling the register writes ourself, we just reuse intel_crt_detect() - Instead of resetting the ADPA during display IRQ installation, we now reset them in vlv_display_power_well_init() Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Lyude <cpaul@redhat.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> [danvet: Rebase over dev_priv/drm_device embedding.] Signed-off-by:
-
Lyude authored
commit 28cf71ce upstream. This lets call intel_crt_reset() in contexts where IRQs are disabled and as such, can't hold the locks required to work with the connectors. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by:
-
Jan Kara authored
commit 31051c85 upstream. inode_change_ok() will be resposible for clearing capabilities and IMA extended attributes and as such will need dentry. Give it as an argument to inode_change_ok() instead of an inode. Also rename inode_change_ok() to setattr_prepare() to better relect that it does also some modifications in addition to checks. Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jan Kara <jack@suse.cz> [bwh: Backported to 3.16: - Drop changes to orangefs, overlayfs - Adjust filenames, context - In nfsd, pass dentry to nfsd_sanitize_attrs() - Update ext3 as well] Signed-off-by:
-
Jan Kara authored
commit 62490330 upstream. To avoid clearing of capabilities or security related extended attributes too early, inode_change_ok() will need to take dentry instead of inode. Propagate it down to fuse_do_setattr(). Acked-by:
Miklos Szeredi <mszeredi@redhat.com> Reviewed-by:
-
