- 23 Nov, 2018 34 commits
-
-
Tristram Ha authored
[ Upstream commit 284fb78e ] Initialize mutex before use. Avoid kernel complaint when CONFIG_DEBUG_LOCK_ALLOC is enabled. Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477") Signed-off-by:
Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by:
Pavel Machek <pavel@ucw.cz> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Subash Abhinov Kasiviswanathan authored
[ Upstream commit d02854dc ] A null dereference was observed when a sysctl was being set from userspace and rmnet was stuck trying to complete some actions in the NETDEV_REGISTER callback. This is because the real_dev is set only after the device registration handler completes. sysctl call stack - <6> Unable to handle kernel NULL pointer dereference at virtual address 00000108 <2> pc : rmnet_vnd_get_iflink+0x1c/0x28 <2> lr : dev_get_iflink+0x2c/0x40 <2> rmnet_vnd_get_iflink+0x1c/0x28 <2> inet6_fill_ifinfo+0x15c/0x234 <2> inet6_ifinfo_notify+0x68/0xd4 <2> ndisc_ifinfo_sysctl_change+0x1b8/0x234 <2> proc_sys_call_handler+0xac/0x100 <2> proc_sys_write+0x3c/0x4c <2> __vfs_write+0x54/0x14c <2> vfs_write+0xcc/0x188 <2> SyS_write+0x60/0xc0 <2> el0_svc_naked+0x34/0x38 device register call stack - <2> notifier_call_chain+0x84/0xbc <2> raw_notifier_call_chain+0x38/0x48 <2> call_netdevice_notifiers_info+0x40/0x70 <2> call_netdevice_notifiers+0x38/0x60 <2> register_netdevice+0x29c/0x3d8 <2> rmnet_vnd_newlink+0x68/0xe8 <2> rmnet_newlink+0xa0/0x160 <2> rtnl_newlink+0x57c/0x6c8 <2> rtnetlink_rcv_msg+0x1dc/0x328 <2> netlink_rcv_skb+0xac/0x118 <2> rtnetlink_rcv+0x24/0x30 <2> netlink_unicast+0x158/0x1f0 <2> netlink_sendmsg+0x32c/0x338 <2> sock_sendmsg+0x44/0x60 <2> SyS_sendto+0x150/0x1ac <2> el0_svc_naked+0x34/0x38 Fixes: b752eff5 ("net: qualcomm: rmnet: Implement ndo_get_iflink") Signed-off-by:
Sean Tranchetti <stranche@codeaurora.org> Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by:
-
Xin Long authored
[ Upstream commit 12480e3b ] According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to defined as SCTP_SS_FCFS or SCTP_SS_RR. SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch. Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations") Reported-by:
Jianwen Ji <jiji@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Holger Hoffstätte authored
[ Upstream commit 0432e833 ] Since 4.19 the following error in sysfs has appeared when using the r8169 NIC driver: $cd /sys/module/realtek/drivers $ls -l ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory [..garbled dir entries follow..] Apparently the forward slash in "10/100Mbps Ethernet" is interpreted as directory separator that leads nowhere, and was introduced in commit 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions"). Fix this by removing the offending slash in the driver name. Other drivers in net/phy seem to have the same problem, but I cannot test/verify them. Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by:
Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by:
-
Andrew Lunn authored
[ Upstream commit a9049ff9 ] The mv88e6161 would sometime fail to probe with a timeout waiting for the switch to complete an operation. This operation is supposed to clear the statistics counters. However, due to a read/modify/write, without the needed mask, the operation actually carried out was more random, with invalid parameters, resulting in the switch not responding. We need to preserve the histogram mode bits, so apply a mask to keep them. Reported-by:
Chris Healy <Chris.Healy@zii.aero> Fixes: 40cff8fc ("net: dsa: mv88e6xxx: Fix stats histogram mode") Signed-off-by:
-
Denis Drozdov authored
[ Upstream commit acf3766b ] The mlx5e channels should be closed before mlx5i_uninit_underlay_qp puts the QP into RST (reset) state during mlx5i_close. Currently QP state incorrectly set to RST before channels got deactivated and closed, since mlx5_post_send request expects QP in RTS (Ready To Send) state. The fix is to keep QP in RTS state until mlx5e channels get closed and to reset QP afterwards. Also this fix is simply correct in order to keep the open/close flow symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open, the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing at close, which is exactly what this patch is doing. Fixes: dae37456 ("net/mlx5: Support for attaching multiple underlay QPs to root flow table") Signed-off-by:
Denis Drozdov <denisd@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Raed Salem authored
[ Upstream commit f2b18732 ] The commit "net/mlx5: Refactor accel IPSec code" introduced a bug where asynchronous short time change in hash key value by create/release SA context might happen during an asynchronous hash resize operation this could cause a subsequent remove SA context operation to fail as the key value used during resize is not the same key value used when remove SA context operation is invoked. This commit fixes the bug by defining the SA context hash key such that it includes only fields that never change during the lifetime of the SA context object. Fixes: d6c4f029 ("net/mlx5: Refactor accel IPSec code") Signed-off-by:
Raed Salem <raeds@mellanox.com> Reviewed-by:
Aviad Yehezkel <aviadye@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit f8504f4c ] This issue happens when trying to add an existent tunnel. It doesn't call sock_put() before returning -EEXIST to release the sock refcnt that was held by calling sock_hold() before the existence check. This patch is to fix it by holding the sock after doing the existence check. Fixes: f6cd651b ("l2tp: fix race in duplicate tunnel detection") Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 0d5b9311 ] Multiple cpus might attempt to insert a new fragment in rhashtable, if for example RPS is buggy, as reported by 배석진 in https://patchwork.ozlabs.org/patch/994601/ We use rhashtable_lookup_get_insert_key() instead of rhashtable_insert_fast() to let cpus losing the race free their own inet_frag_queue and use the one that was inserted by another cpu. Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
배석진 <soukjin.bae@samsung.com> Signed-off-by:
-
Shay Agroskin authored
[ Upstream commit 64e28334 ] Querying interface FEC caps with 'ethtool [int]' after link reset throws warning regading link speed. This warning is not needed as there is already an indication in user space that the link is not up. Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration") Signed-off-by:
Shay Agroskin <shayag@mellanox.com> Signed-off-by:
-
Valentine Fatiev authored
[ Upstream commit 228c4cd0 ] Loopback test had fixed packet size, which can be bigger than configured MTU. Shorten the loopback packet size to be bigger than minimal MTU allowed by the device. Text field removed from struct 'mlx5ehdr' as redundant to allow send small packets as minimal allowed MTU. Fixes: d605d668 ("net/mlx5e: Add support for ethtool self diagnostics test") Signed-off-by:
Valentine Fatiev <valentinef@mellanox.com> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 83621b7d ] We get the match level (none, l2, l3, l4) while going over the match dissectors of an offloaded tc rule. When doing this, the match level enum and the not min inline enum values should be used, fix that. This worked accidentally b/c both enums have the same numerical values. Fixes: d708f902 ('net/mlx5e: Get the required HW match level while parsing TC flow matches') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 69fec325 ] This reverts commit 22d7be26. The dst's mtu in transport can be updated by a non sctp place like in xfrm where the MTU information didn't get synced between asoc, transport and dst, so it is still needed to do the pmtu check in sctp_packet_config. Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Moshe Shemesh authored
[ Upstream commit 0073c8f7 ] In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means that WQE (RX descriptor) can be used for many packets and so the WQE is much bigger than MTU. In virtualization setups where the port mtu can be larger than the vf mtu, if received packet is bigger than MTU, it won't be dropped by HW on too small receive WQE. If we use linear SKB in striding RQ, since each stride has room for mtu size payload and skb info, an oversized packet can lead to crash for crossing allocated page boundary upon the call to build_skb. So driver needs to check packet size and drop it. Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the number of packets dropped by the driver for being too large. As a new field is added to the RQ struct, re-open the channels whenever this field is being used in datapath (i.e., in the case of linear Striding RQ). Fixes: 619a8f2a ("net/mlx5e: Use linear SKB in Striding RQ") Signed-off-by:
Moshe Shemesh <moshe@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Yuval Avnery authored
[ Upstream commit a1f240f1 ] When core driver enters deattach/attach flow after pci reset, Number of logical CPUs may have changed. As a result we need to update the cpu affiliated resource tables. 1. indirect rqt list 2. eq table Reproduction (PowerPC): echo 1000 > /sys/kernel/debug/powerpc/eeh_max_freezes ppc64_cpu --smt=on # Restart driver modprobe -r ... ; modprobe ... # Link up ifconfig ... # Only physical CPUs ppc64_cpu --smt=off # Inject PCI errors so PCI will reset - calling the pci error handler echo 0x8000000000000000 > /sys/kernel/debug/powerpc/<PCI BUS>/err_injct_inboundA Call trace when trying to add non-existing rqs to an indirect rqt: mlx5e_redirect_rqt+0x84/0x260 [mlx5_core] (unreliable) mlx5e_redirect_rqts+0x188/0x190 [mlx5_core] mlx5e_activate_priv_channels+0x488/0x570 [mlx5_core] mlx5e_open_locked+0xbc/0x140 [mlx5_core] mlx5e_open+0x50/0x130 [mlx5_core] mlx5e_nic_enable+0x174/0x1b0 [mlx5_core] mlx5e_attach_netdev+0x154/0x290 [mlx5_core] mlx5e_attach+0x88/0xd0 [mlx5_core] mlx5_attach_device+0x168/0x1e0 [mlx5_core] mlx5_load_one+0x1140/0x1210 [mlx5_core] mlx5_pci_resume+0x6c/0xf0 [mlx5_core] Create cq will fail when trying to use non-existing EQ. Fixes: 89d44f0a ("net/mlx5_core: Add pci error handlers to mlx5_core driver") Signed-off-by:
Yuval Avnery <yuvalav@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 077ecd78 ] Currently, we are only supporting tc hw offloads when the eswitch support is compiled in, but we are not gating the adevertizment of the NETIF_F_HW_TC feature on this config being set. Fix it, and while doing that, also avoid dealing with the feature on ethtool when the config is not set. Fixes: e8f887ac ('net/mlx5e: Introduce tc offload support') Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit d3a80bb5 ] For the "all" ethertype we should not care whether the packet has vlans. Besides being wrong, the way we did it caused FW error for rules such as: tc filter add dev eth0 protocol all parent ffff: \ prio 1 flower skip_sw action drop b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec) wasn't set. Fix that by matching on vlan non-existence only if we were also told to match on the ethertype. Fixes: cee26487 ('net/mlx5e: Set vlan masks for all offloaded TC rules') Signed-off-by:
Slava Ovsiienko <viacheslavo@mellanox.com> Reviewed-by:
Jianbo Liu <jianbol@mellanox.com> Reviewed-by:
-
Jon Maloy authored
[ Upstream commit 7ab412d3 ] When a link failure is detected locally, the link is reset, the flag link->in_session is set to false, and a RESET_MSG with the 'stopping' bit set is sent to the peer. The purpose of this bit is to inform the peer that this endpoint just is going down, and that the peer should handle the reception of this particular RESET message as a local failure. This forces the peer to accept another RESET or ACTIVATE message from this endpoint before it can re-establish the link. This again is necessary to ensure that link session numbers are properly exchanged before the link comes up again. If a failure is detected locally at the same time at the peer endpoint this will do the same, which is also a correct behavior. However, when receiving such messages, the endpoints will not distinguish between 'stopping' RESETs and ordinary ones when it comes to updating session numbers. Both endpoints will copy the received session number and set their 'in_session' flags to true at the reception, while they are still expecting another RESET from the peer before they can go ahead and re-establish. This is contradictory, since, after applying the validation check referred to below, the 'in_session' flag will cause rejection of all such messages, and the link will never come up again. We now fix this by not only handling received RESET/STOPPING messages as a local failure, but also by omitting to set a new session number and the 'in_session' flag in such cases. Fixes: 7ea817f4 ("tipc: check session number before accepting link protocol messages") Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit 63c82997 ] TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only currently contain further nested attributes, which are parsed by hand, so the policy is never actually used resulting in a W=1 build warning: net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=] enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = { Add the validation anyway to avoid potential bugs when other attributes are added and to make the attribute structure slightly more clear. Validation will also set extact to point to bad attribute on error. Fixes: 0a6e7778 ("net/sched: allow flower to match tunnel options") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Simon Horman <simon.horman@netronome.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit 19ab6910 ] tcf_idr_check_alloc() can return a negative value, on allocation failures (-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases. Fixes: 0190c1d4 ("net: sched: atomically check-allocate action") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 7cb6a2a2 ] A timing hazard exists when the network interface is stopped that allows a watchdog timeout to be processed by a separate core in parallel. This creates the potential for the timeout handler to wake the queues while the driver is shutting down, or access registers after their clocks have been removed. The more common case is that the watchdog timeout will produce a warning message which doesn't lead to a crash. The chances of this are greatly increased by the fact that bcm_sysport_netif_stop stops the transmit queues which can easily precipitate a watchdog time- out because of stale trans_start data in the queues. This commit corrects the behavior by ensuring that the watchdog timeout is disabled before enterring bcm_sysport_netif_stop. There are currently only two users of the bcm_sysport_netif_stop function: close and suspend. The close case already handles the issue by exiting the RUNNING state before invoking the driver close service. The suspend case now performs the netif_device_detach to exit the PRESENT state before the call to bcm_sysport_netif_stop rather than after it. These behaviors prevent any future scheduling of the driver timeout service during the window. The netif_tx_stop_all_queues function in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure synchronization with any transmit or timeout threads that may already be executing on other cores. For symmetry, the netif_device_attach call upon resume is moved to after the call to bcm_sysport_netif_start. Since it wakes the transmit queues it is not necessary to invoke netif_tx_start_all_queues from bcm_sysport_netif_start so it is moved into the driver open service. Fixes: 40755a0f ("net: systemport: add suspend and resume support") Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
-
Matthew Cover authored
[ Upstream commit 8ebebcba ] When writing packets to a descriptor associated with a combined queue, the packets should end up on that queue. Before this change all packets written to any descriptor associated with a tap interface end up on rx-0, even when the descriptor is associated with a different queue. The rx traffic can be generated by either of the following. 1. a simple tap program which spins up multiple queues and writes packets to each of the file descriptors 2. tx from a qemu vm with a tap multiqueue netdev The queue for rx traffic can be observed by either of the following (done on the hypervisor in the qemu case). 1. a simple netmap program which opens and reads from per-queue descriptors 2. configuring RPS and doing per-cpu captures with rxtxcpu Alternatively, if you printk() the return value of skb_get_rx_queue() just before each instance of netif_receive_skb() in tun.c, you will get 65535 for every skb. Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes the association between descriptor and rx queue. Signed-off-by:
Matthew Cover <matthew.cover@stackpath.com> Signed-off-by:
-
Jon Maloy authored
[ Upstream commit adba75be ] We get the following warning: [ 47.926140] 32-bit node address hash set to 2010a0a [ 47.927202] [ 47.927433] ================================ [ 47.928050] WARNING: inconsistent lock state [ 47.928661] 4.19.0+ #37 Tainted: G E [ 47.929346] -------------------------------- [ 47.929954] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 47.930116] swapper/3/0 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 47.930116] 00000000af8bc31e (&(&ht->lock)->rlock){+.?.}, at: rhashtable_walk_enter+0x36/0xb0 [ 47.930116] {SOFTIRQ-ON-W} state was registered at: [ 47.930116] _raw_spin_lock+0x29/0x60 [ 47.930116] rht_deferred_worker+0x556/0x810 [ 47.930116] process_one_work+0x1f5/0x540 [ 47.930116] worker_thread+0x64/0x3e0 [ 47.930116] kthread+0x112/0x150 [ 47.930116] ret_from_fork+0x3a/0x50 [ 47.930116] irq event stamp: 14044 [ 47.930116] hardirqs last enabled at (14044): [<ffffffff9a07fbba>] __local_bh_enable_ip+0x7a/0xf0 [ 47.938117] hardirqs last disabled at (14043): [<ffffffff9a07fb81>] __local_bh_enable_ip+0x41/0xf0 [ 47.938117] softirqs last enabled at (14028): [<ffffffff9a0803ee>] irq_enter+0x5e/0x60 [ 47.938117] softirqs last disabled at (14029): [<ffffffff9a0804a5>] irq_exit+0xb5/0xc0 [ 47.938117] [ 47.938117] other info that might help us debug this: [ 47.938117] Possible unsafe locking scenario: [ 47.938117] [ 47.938117] CPU0 [ 47.938117] ---- [ 47.938117] lock(&(&ht->lock)->rlock); [ 47.938117] <Interrupt> [ 47.938117] lock(&(&ht->lock)->rlock); [ 47.938117] [ 47.938117] *** DEADLOCK *** [ 47.938117] [ 47.938117] 2 locks held by swapper/3/0: [ 47.938117] #0: 0000000062c64f90 ((&d->timer)){+.-.}, at: call_timer_fn+0x5/0x280 [ 47.938117] #1: 00000000ee39619c (&(&d->lock)->rlock){+.-.}, at: tipc_disc_timeout+0xc8/0x540 [tipc] [ 47.938117] [ 47.938117] stack backtrace: [ 47.938117] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G E 4.19.0+ #37 [ 47.938117] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 47.938117] Call Trace: [ 47.938117] <IRQ> [ 47.938117] dump_stack+0x5e/0x8b [ 47.938117] print_usage_bug+0x1ed/0x1ff [ 47.938117] mark_lock+0x5b5/0x630 [ 47.938117] __lock_acquire+0x4c0/0x18f0 [ 47.938117] ? lock_acquire+0xa6/0x180 [ 47.938117] lock_acquire+0xa6/0x180 [ 47.938117] ? rhashtable_walk_enter+0x36/0xb0 [ 47.938117] _raw_spin_lock+0x29/0x60 [ 47.938117] ? rhashtable_walk_enter+0x36/0xb0 [ 47.938117] rhashtable_walk_enter+0x36/0xb0 [ 47.938117] tipc_sk_reinit+0xb0/0x410 [tipc] [ 47.938117] ? mark_held_locks+0x6f/0x90 [ 47.938117] ? __local_bh_enable_ip+0x7a/0xf0 [ 47.938117] ? lockdep_hardirqs_on+0x20/0x1a0 [ 47.938117] tipc_net_finalize+0xbf/0x180 [tipc] [ 47.938117] tipc_disc_timeout+0x509/0x540 [tipc] [ 47.938117] ? call_timer_fn+0x5/0x280 [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] call_timer_fn+0xa1/0x280 [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] run_timer_softirq+0x1f2/0x4d0 [ 47.938117] __do_softirq+0xfc/0x413 [ 47.938117] irq_exit+0xb5/0xc0 [ 47.938117] smp_apic_timer_interrupt+0xac/0x210 [ 47.938117] apic_timer_interrupt+0xf/0x20 [ 47.938117] </IRQ> [ 47.938117] RIP: 0010:default_idle+0x1c/0x140 [ 47.938117] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 54 55 53 65 8b 2d d8 2b 74 65 0f 1f 44 00 00 e8 c6 2c 8b ff fb f4 <65> 8b 2d c5 2b 74 65 0f 1f 44 00 00 5b 5d 41 5c c3 65 8b 05 b4 2b [ 47.938117] RSP: 0018:ffffaf6ac0207ec8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13 [ 47.938117] RAX: ffff8f5b3735e200 RBX: 0000000000000003 RCX: 0000000000000001 [ 47.938117] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff8f5b3735e200 [ 47.938117] RBP: 0000000000000003 R08: 0000000000000001 R09: 0000000000000000 [ 47.938117] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 [ 47.938117] R13: 0000000000000000 R14: ffff8f5b3735e200 R15: ffff8f5b3735e200 [ 47.938117] ? default_idle+0x1a/0x140 [ 47.938117] do_idle+0x1bc/0x280 [ 47.938117] cpu_startup_entry+0x19/0x20 [ 47.938117] start_secondary+0x187/0x1c0 [ 47.938117] secondary_startup_64+0xa4/0xb0 The reason seems to be that tipc_net_finalize()->tipc_sk_reinit() is calling the function rhashtable_walk_enter() within a timer interrupt. We fix this by executing tipc_net_finalize() in work queue context. Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Jon Maloy authored
[ Upstream commit 1c1274a5 ] The code for reading ancillary data from a received buffer is assuming the buffer is linear. To make this assumption true we have to linearize the buffer before message data is read. Signed-off-by:
-
Siva Reddy Kallam authored
[ Upstream commit 59663e42 ] This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change ring and flow control paths. This patch solves the RX hang while doing continuous ring or flow control parameters with heavy traffic from peer. Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Stephen Mallon authored
[ Upstream commit cadf9df2 ] During tcp coalescing ensure that the skb hardware timestamp refers to the highest sequence number data. Previously only the software timestamp was updated during coalescing. Signed-off-by:
Stephen Mallon <stephen.mallon@sydney.edu.au> Signed-off-by:
-
Xin Long authored
[ Upstream commit cc3ccf26 ] As rfc7496#section4.5 says about SCTP_PR_SUPPORTED: This socket option allows the enabling or disabling of the negotiation of PR-SCTP support for future associations. For existing associations, it allows one to query whether or not PR-SCTP support was negotiated on a particular association. It means only sctp sock's prsctp_enable can be set. Note that for the limitation of SCTP_{CURRENT|ALL}_ASSOC, we will add it when introducing SCTP_{FUTURE|CURRENT|ALL}_ASSOC for linux sctp in another patchset. v1->v2: - drop the params.assoc_id check as Neil suggested. Fixes: 28aa4c26 ("sctp: add SCTP_PR_SUPPORTED on sctp sockopt") Reported-by:
Ying Xu <yinxu@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 33d9a2c7 ] eth_type_trans() assumes initial value for skb->pkt_type is PACKET_HOST. This is indeed the value right after a fresh skb allocation. However, it is possible that GRO merged a packet with a different value (like PACKET_OTHERHOST in case macvlan is used), so we need to make sure napi->skb will have pkt_type set back to PACKET_HOST. Otherwise, valid packets might be dropped by the stack because their pkt_type is not PACKET_HOST. napi_reuse_skb() was added in commit 96e93eab ("gro: Add internal interfaces for VLAN"), but this bug always has been there. Fixes: 96e93eab ("gro: Add internal interfaces for VLAN") Signed-off-by:
-
Doug Berger authored
A timing hazard exists when the network interface is stopped that allows a watchdog timeout to be processed by a separate core in parallel. This creates the potential for the timeout handler to wake the queues while the driver is shutting down, or access registers after their clocks have been removed. The more common case is that the watchdog timeout will produce a warning message which doesn't lead to a crash. The chances of this are greatly increased by the fact that bcmgenet_netif_stop stops the transmit queues which can easily precipitate a watchdog time- out because of stale trans_start data in the queues. This commit corrects the behavior by ensuring that the watchdog timeout is disabled before enterring bcmgenet_netif_stop. There are currently only two users of the bcmgenet_netif_stop function: close and suspend. The close case already handles the issue by exiting the RUNNING state before invoking the driver close service. The suspend case now performs the netif_device_detach to exit the PRESENT state before the call to bcmgenet_netif_stop rather than after it. These behaviors prevent any future scheduling of the driver timeout service during the window. The netif_tx_stop_all_queues function in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure synchronization with any transmit or timeout threads that may already be executing on other cores. For symmetry, the netif_device_attach call upon resume is moved to after the call to bcmgenet_netif_start. Since it wakes the transmit queues it is not necessary to invoke netif_tx_start_all_queues from bcmgenet_netif_start so it is moved into the driver open service. [ Upstream commit 09e805d2 ] Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
-
David Ahern authored
[ Upstream commit 7ddacfa5 ] Preethi reported that PMTU discovery for UDP/raw applications is not working in the presence of VRF when the socket is not bound to a device. The problem is that ip6_sk_update_pmtu does not consider the L3 domain of the skb device if the socket is not bound. Update the function to set oif to the L3 master device if relevant. Fixes: ca254490 ("net: Add VRF support to IPv6 stack") Reported-by:
Preethi Ramachandra <preethir@juniper.net> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 761f6026 ] These is no need to hold dst before calling rt6_remove_exception_rt(). The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(), which has been removed in Commit 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes"). Otherwise, it will cause a dst leak. This patch is to simply remove the dst_hold_safe() call before calling rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt(). It's safe, because the removal of the exception that holds its dst's refcnt is protected by rt6_exception_lock. Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes") Fixes: 23fb93a4 ("net/ipv6: Cleanup exception and cache route handling") Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 16f7eb2b ] The various types of tunnels running over IPv4 can ask to set the DF bit to do PMTU discovery. However, PMTU discovery is subject to the threshold set by the net.ipv4.route.min_pmtu sysctl, and is also disabled on routes with "mtu lock". In those cases, we shouldn't set the DF bit. This patch makes setting the DF bit conditional on the route's MTU locking state. This issue seems to be older than git history. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Michał Mirosław authored
[ Upstream commit e84b4794 ] Don't request tag insertion when it isn't present in outgoing skb. Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
-
배석진 authored
[ Upstream commit 62230715 ] Only first fragment has the sport/dport information, not the following ones. If we want consistent hash for all fragments, we need to ignore ports even for first fragment. This bug is visible for IPv6 traffic, if incoming fragments do not have a flow label, since skb_get_hash() will give different results for first fragment and following ones. It is also visible if any routing rule wants dissection and sport or dport. See commit 5e5d6fed ("ipv6: route: dissect flow in input path if fib rules need it") for details. [edumazet] rewrote the changelog completely. Fixes: 06635a35 ("flow_dissect: use programable dissector in skb_flow_dissect and friends") Signed-off-by:
-
- 21 Nov, 2018 6 commits
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
This reverts commit 22083c02 which is commit 4abb951b upstream. Jean writes: This commit was tagged with: Link: https://bugzilla.kernel.org/show_bug.cgi?id=200011 Tested-by: Jean-Marc Lenoir Cc: All applicable <stable@vger.kernel.org> making it sound like it was fixing an actual bug. This is not the case. The commit fixes a side issue discovered while investigating bug #200011. It does NOT fix bug #200011 itself (as explicitly reported by Jean-Marc at https://bugzilla.kernel.org/show_bug.cgi?id=200011#c65 ). It does however cause regressions, despite what the commit message says. See: https://bugzilla.kernel.org/show_bug.cgi?id=201721 and I expect more similar regressions, as ACPI resource conflicts are very frequent. This commit was not stable material to start with. It is intrusive, presents a risk of side effects, and does not solve an actual bug that is bothering users. Reported-by:
Jean Delvare <jdelvare@suse.de> Cc: Jean-Marc Lenoir <archlinux@jihemel.com> Cc: Erik Schmauss <erik.schmauss@intel.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Stefano Stabellini authored
commit f9005571 upstream. xen_create_contiguous_region has now only an implementation if CONFIG_XEN_PV is defined. However, on ARM we never set CONFIG_XEN_PV but we do have an implementation of xen_create_contiguous_region which is required for swiotlb-xen to work correctly (although it just sets *dma_handle). [backport: remove change to xen_remap_pfn] Cc: <stable@vger.kernel.org> # 4.12 Fixes: 16624390 ("xen: create xen_create/destroy_contiguous_region() stubs for PVHVM only builds") Signed-off-by:
Stefano Stabellini <stefanos@xilinx.com> Reviewed-by:
Juergen Gross <jgross@suse.com> CC: Jeff.Kubascik@dornerworks.com CC: Jarvis.Roach@dornerworks.com CC: Nathan.Studer@dornerworks.com CC: vkuznets@redhat.com CC: boris.ostrovsky@oracle.com CC: jgross@suse.com CC: julien.grall@arm.com Signed-off-by:
-
Ville Syrjälä authored
commit 44a7276b upstream. In my haste to remove irq_port[] I accidentally changed the way we deal with hpd pins that are shared by multiple encoders (DP and HDMI for pre-DDI platforms). Previously we would only handle such pins via ->hpd_pulse(), but now we queue up the hotplug work for the HDMI encoder directly. Worse yet, we now count each hpd twice and this increment the hpd storm count twice as fast. This can lead to spurious storms being detected. Go back to the old way of doing things, ie. delegate to ->hpd_pulse() for any pin which has an encoder with that hook implemented. I don't really like the idea of adding irq_port[] back so let's loop through the encoders first to check if we have an encoder with ->hpd_pulse() for the pin, and then go through all the pins and decided on the correct course of action based on the earlier findings. I have occasionally toyed with the idea of unifying the pre-DDI HDMI and DP encoders into a single encoder as well. Besides the hotplug processing it would have the other benefit of preventing userspace from trying to enable both encoders at the same time. That is simply illegal as they share the same clock/data pins. We have some testcases that will attempt that and thus fail on many older machines. But for now let's stick to fixing just the hotplug code. Cc: stable@vger.kernel.org # 4.19+ Cc: Lyude Paul <lyude@redhat.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Fixes: b6ca3eee ("drm/i915: Nuke dev_priv->irq_port[]") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181108200424.28371-1-ville.syrjala@linux.intel.comReviewed-by:
Lyude Paul <lyude@redhat.com> (cherry picked from commit 5a3aeca9) Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by:
-
Lyude Paul authored
commit 541ff7e9 upstream. Turns out that if you trigger an HPD storm on a system that has an MST topology connected to it, you'll end up causing the kernel to eventually hit a NULL deref: [ 332.339041] BUG: unable to handle kernel NULL pointer dereference at 00000000000000ec [ 332.340906] PGD 0 P4D 0 [ 332.342750] Oops: 0000 [#1] SMP PTI [ 332.344579] CPU: 2 PID: 25 Comm: kworker/2:0 Kdump: loaded Tainted: G O 4.18.0-rc3short-hpd-storm+ #2 [ 332.346453] Hardware name: LENOVO 20BWS1KY00/20BWS1KY00, BIOS JBET71WW (1.35 ) 09/14/2018 [ 332.348361] Workqueue: events intel_hpd_irq_storm_reenable_work [i915] [ 332.350301] RIP: 0010:intel_hpd_irq_storm_reenable_work.cold.3+0x2f/0x86 [i915] [ 332.352213] Code: 00 00 ba e8 00 00 00 48 c7 c6 c0 aa 5f a0 48 c7 c7 d0 73 62 a0 4c 89 c1 4c 89 04 24 e8 7f f5 af e0 4c 8b 04 24 44 89 f8 29 e8 <41> 39 80 ec 00 00 00 0f 85 43 13 fc ff 41 0f b6 86 b8 04 00 00 41 [ 332.354286] RSP: 0018:ffffc90000147e48 EFLAGS: 00010006 [ 332.356344] RAX: 0000000000000005 RBX: ffff8802c226c9d4 RCX: 0000000000000006 [ 332.358404] RDX: 0000000000000000 RSI: 0000000000000082 RDI: ffff88032dc95570 [ 332.360466] RBP: 0000000000000005 R08: 0000000000000000 R09: ffff88031b3dc840 [ 332.362528] R10: 0000000000000000 R11: 000000031a069602 R12: ffff8802c226ca20 [ 332.364575] R13: ffff8802c2268000 R14: ffff880310661000 R15: 000000000000000a [ 332.366615] FS: 0000000000000000(0000) GS:ffff88032dc80000(0000) knlGS:0000000000000000 [ 332.368658] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 332.370690] CR2: 00000000000000ec CR3: 000000000200a003 CR4: 00000000003606e0 [ 332.372724] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 332.374773] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 332.376798] Call Trace: [ 332.378809] process_one_work+0x1a1/0x350 [ 332.380806] worker_thread+0x30/0x380 [ 332.382777] ? wq_update_unbound_numa+0x10/0x10 [ 332.384772] kthread+0x112/0x130 [ 332.386740] ? kthread_create_worker_on_cpu+0x70/0x70 [ 332.388706] ret_from_fork+0x35/0x40 [ 332.390651] Modules linked in: i915(O) vfat fat joydev btusb btrtl btbcm btintel bluetooth ecdh_generic iTCO_wdt wmi_bmof i2c_algo_bit drm_kms_helper intel_rapl syscopyarea sysfillrect x86_pkg_temp_thermal sysimgblt coretemp fb_sys_fops crc32_pclmul drm psmouse pcspkr mei_me mei i2c_i801 lpc_ich mfd_core i2c_core tpm_tis tpm_tis_core thinkpad_acpi wmi tpm rfkill video crc32c_intel serio_raw ehci_pci xhci_pci ehci_hcd xhci_hcd [last unloaded: i915] [ 332.394963] CR2: 00000000000000ec This appears to be due to the fact that with an MST topology, not all intel_connector structs will have ->encoder set. So, fix this by skipping connectors without encoders in intel_hpd_irq_storm_reenable_work(). For those wondering, this bug was found on accident while simulating HPD storms using a Chamelium connected to a ThinkPad T450s (Broadwell). Changes since v1: - Check intel_connector->mst_port instead of intel_connector->encoder Signed-off-by:
-
Lyude Paul authored
commit 7c451230 upstream. This hasn't caused any issues yet that I'm aware of, but as Ville Syrjälä pointed out - we need to make sure that intel_connector->mst_port is set before initializing MST connectors, since in theory we could potentially check intel_connector->mst_port in i915_hpd_poll_init_work() after registering the connector but before having written it's value. Signed-off-by:
-
