- 25 Nov, 2021 4 commits
-
-
Lukas Bulwahn authored
Commit 04544222 ("ASoC: codecs: wcd938x: add audio routing and Kconfig") adds SND_SOC_WCD937X, which does not exist, and SND_SOC_WCD938X, which seems not really to be the intended config to be selected, but only a supporting config symbol to the actual config SND_SOC_WCD938X_SDW for the codec. Add SND_SOC_WCD938_SDW to the list instead of SND_SOC_WCD93{7,8}X. The issue was identified with ./scripts/checkkconfigsymbols.py. Fixes: 04544222 ("ASoC: codecs: wcd938x: add audio routing and Kconfig") Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20211125095158.8394-3-lukas.bulwahn@gmail.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Lukas Bulwahn authored
Commit f37fe2f9 ("ASoC: uniphier: add support for UniPhier AIO common driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the non-existing config SND_SOC_UNIPHIER_AIO_DMA. Hence, ./scripts/checkkconfigsymbols.py warns: SND_SOC_UNIPHIER_AIO_DMA Referencing files: sound/soc/uniphier/Kconfig Probably, there is actually no further config intended to be selected here. So, just drop selecting the non-existing config. Fixes: f37fe2f9 ("ASoC: uniphier: add support for UniPhier AIO common driver") Signed-off-by:
-
Yang Yingliang authored
The node pointer is returned by of_parse_phandle() with refcount incremented in platform_parse_resource(). Calling of_node_put() to aovid the refcount leak. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20211125071608.3056715-1-yangyingliang@huawei.comSigned-off-by:
-
Jiaxin Yu authored
The unnecessary conditional inclusion caused the following warning. Such as: >> sound/soc/mediatek/mt8192/mt8192-afe-pcm.c:2368:32: warning: unused >> variable 'mt8192_afe_pm_ops' [-Wunused-const-variable] static const struct dev_pm_ops mt8192_afe_pm_ops = { Because runtime_pm already handles the case without CONFIG_PM, we can remove CONFIG_PM condition. Signed-off-by:Jiaxin Yu <jiaxin.yu@mediatek.com> Reported-by:
kernel test robot <lkp@intel.com> Acked-by:
Tzung-Bi Shih <tzungbi@google.com> Link: https://lore.kernel.org/r/20211125042422.2349-1-jiaxin.yu@mediatek.comSigned-off-by:
-
- 24 Nov, 2021 8 commits
-
-
Mark Brown authored
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>: The use of the SPIB register helps reduce power consumption - though to a smaller degree than DMI_L1. This hardware capability is however incompatible with userspace-initiated rewinds typically used by PulseAudio. In the past (2015..2017) Intel suggested an API extension to let applications disable rewinds. At the time the feedback was that such a capability was too Intel-specific and SPIB remained unused except for loading DSP code. We now see devices with smaller batteries being released, and it's time to revisit Linux support for SPIB to extend battery life. In this update the rewinds are disabled via an opt-in kernel parameter. In the previous reviews, there was consensus that a Kconfig option was too complicated for distributions to set, and we are missing a TBD API to expose such capabilities to user-space. The debate on whether or not to use rewinds, and the impact of disabling rewinds, will likely be closed when Intel releases the 'deep-buffer' support, currently under development [2][3]. With this solution, rewinds will not be needed, ever. When an application deals with content that is not latency-sensitive (e.g. music playback), it will be able to reduce power consumption by selecting a different PCM device with increased buffering capabilities. Low-latency streams will be handled by the 'regular' path. In other words, the impossible compromise between power and latency will be handled with different PCM devices/profiles for the same endpoint, and we can push the design of capability negotiation to a later time when all the building blocks (firmware topology, kernel, userspace) are ready - we still have firmware xruns, DPCM race conditions to solve, and a need to describe these alternate PCM devices with UCM using 'modifiers'.
-
Ranjani Sridharan authored
During system suspend, paused streams do not get suspended. Therefore, we need to explicitly free these PCMs in the DSP and free the associated DAPM widgets so that they can be set up again during resume. Fixes: 5fcdbb2d ("ASoC: SOF: Add support for dynamic pipelines") Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
Paul Olaru <paul.olaru@oss.nxp.com> Reviewed-by:
Bard Liao <bard.liao@intel.com> Reviewed-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20211123171606.129350-3-kai.vehmanen@linux.intel.comSigned-off-by:
-
Pierre-Louis Bossart authored
It's not clear why we would walk the list backwards. That makes no difference. Signed-off-by:
-
Pierre-Louis Bossart authored
Older firmware prior to ABI 3.19 has a dependency where the scheduler widgets need to be setup last. Moving the call to sof_widget_setup() before the pipeline_complete() call also helps remove the need for the 'reverse' direction when walking through the widget list - this was only working because of the topology macros but the topology does not require any order. Fixes: 5fcdbb2d ("ASoC: SOF: Add support for dynamic pipelines") Signed-off-by:
-
Ranjani Sridharan authored
When we disable rewinds, then the .ack can be used to program SPIB with the application pointer, which allows the HDaudio DMA to save power by opportunistically bursting data transfers when the path to memory is enabled (and conversely to shut it down when there are no transfer requests). The SPIB register can only be programmed with incremental values with wrap-around after the DMA RUN bits are set. For simplicity, we set the INFO_NO_REWINDS flag in the .open callback when we already need to program the SNDRV_PCM_INFO_SYNC_APPLPTR flag. Rewinds are not used by many applications. One notable application using rewinds is PulseAudio. Practical experiments with Ubuntu/PulseAudio default settings did not show any audible issues, but the user may hear volume changes and notification with a delay, depending on the size of the ring buffer and latency constraints. The choice of disabling rewinds is exposed as a kernel parameter and not a Kconfig option to avoid any undesirable side-effects. Reviewed-by:
Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by:
-
Ranjani Sridharan authored
Add the indirections required at the core level for platform-specific operations on ack. Note that on errors in the .ack the ALSA core will restore the previous appl_ptr. Reviewed-by:
-
Pierre-Louis Bossart authored
When the hardware can only deal with a monotonically increasing appl_ptr, this flag can be set. In case the application requests a rewind, be it with a snd_pcm_rewind() or with a direct change of a mmap'ed pointer followed by a SNDRV_PCM_IOCTL_SYNC_PTR, this patch checks if a rewind occurred and returns an error. Credits to Takashi Iwai for identifying the path with SYNC_PTR and suggesting the pointer checks. Suggested-by:
Takashi Iwai <tiwai@suse.de> Reviewed-by:
-
Pierre-Louis Bossart authored
In some cases, the appl_ptr passed by userspace is not checked before being used. This patch adds an unconditional check and returns an error code should the appl_ptr exceed the ALSA 'boundary'. Suggested-by:
-
- 22 Nov, 2021 28 commits
-
-
Mark Brown authored
Merge series from Daniel Baluta <daniel.baluta@oss.nxp.com>: This patch series adds support for System PM and Runtime PM with SOF for i.MX8 platforms.
-
Mark Brown authored
Merge series from Olivier Moysan <olivier.moysan@foss.st.com>: Enable support of pm runtime on STM32 SPDIFRX, I2S and DFSDM drivers to allow power state monitoring.
-
Mark Brown authored
Merge series from Ariel D'Alessandro <ariel.dalessandro@collabora.com>: This patchset modifies the tlv320aic31xx driver to update its sysclk if BCLK is used as the input clock. This allows to be used by the generic fsl-asoc-card, without having to add a specific driver.
-
Mark Brown authored
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>: When a pipeline is marked dynamic in the SOF DSP firmware topology definition (the tplg file kernel loads from filesystem), it means the pipeline resources are not allocated when DSP is booted (at driver probe, or at runtime resume), but rather delayed until the pipeline is actually used.
-
Ariel D'Alessandro authored
Add entry for fsl,imx-audio-tlv320aic31xx audio codec. This codec is configured to use BCLK as clock input. Signed-off-by:
Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by:
Ariel D'Alessandro <ariel.dalessandro@collabora.com> Link: https://lore.kernel.org/r/20211119153248.419802-6-ariel.dalessandro@collabora.comSigned-off-by:
-
Ariel D'Alessandro authored
If BCLK is used as PLL input, the sysclk is determined by the hw params. So it must be updated here to match the input frequency, based on sample rate, format and channels. Signed-off-by:
-
Ariel D'Alessandro authored
Add divisors for rates needed when the clk_in is set to BCLK. Signed-off-by:
-
Ariel D'Alessandro authored
When the clock used by the codec is BCLK, the operation parameters need to be calculated from input sample rate and format. Low frequency rates required different r multipliers, in order to achieve a higher PLL output frequency. Signed-off-by:
-
Ariel D'Alessandro authored
Signed-off-by:
-
Richard Fitzgerald authored
When a jack handler is registered in cs42l42_set_jack() the initial state should be reported if an attached headphone/headset has already been detected. The jack detect sequence takes around 1 second: typically long enough for the machine driver to probe and register the jack handler in time to receive the first report from the interrupt handler. So it is possible on some systems that the correct initial state was seen simply because of lucky timing. Modular builds were more likely to miss the reporting of the initial state. Signed-off-by:
Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 4ca239f3 ("ASoC: cs42l42: Always enable TS_PLUG and TS_UNPLUG interrupts") Link: https://lore.kernel.org/r/20211119124854.58939-1-rf@opensource.cirrus.comSigned-off-by:
-
Pierre-Louis Bossart authored
There are already 3 versions of the Up boards with support for the SOF community key (ApolloLake, WhiskyLake, TigerLake). Rather than continue to add quirks for each version, let's add a wildcard. For WHL and TGL, the authentication supports both the SOF community key and the firmware signed with the Intel production key. Given two choices, the community key is the preferred option to allow developers to sign their own firmware. The firmware signed with production key can still be selected if needed with a kernel module option (snd-sof-pci.fw_path="intel/sof") Tested-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by:
-
Olivier Moysan authored
Enable support of pm_runtime on STM32 SPDIFRX driver to allow SPDIFRX power state monitoring. Signed-off-by:
Olivier Moysan <olivier.moysan@foss.st.com> Link: https://lore.kernel.org/r/20211119104752.13564-4-olivier.moysan@foss.st.comSigned-off-by:
-
Olivier Moysan authored
Enable support of pm_runtime on STM32 DFSDM audio driver to allow power state monitoring. Signed-off-by:
-
Olivier Moysan authored
Enable support of pm_runtime on STM32 I2S driver to allow I2S power state monitoring. Signed-off-by:
-
Ranjani Sridharan authored
To keep the widget use_counts balanced, free the DAI widget during suspend and also during the stop trigger. Signed-off-by:
Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by:
-
Ranjani Sridharan authored
This patch adds support for dynamic pipelines with multi-core by using the platform-specific core_get/put() ops to power up/down a core when a widget is set up/freed. Along with this, a few redundant functions are removed: 1. sof_pipeline_core_enable() is no longer needed as the pipeline core will be set up when the pipeline widget is set up 2. sof_core_enable() is replaced with snd_sof_core_get() 4. core_power_up/down() DSP ops are deprecated and replaced with core get/put ops. 5. Core power down in sof_widget_unload() during topology removal is also removed as it is not really needed. For dynamic pipelines, the cores will be powered off when they are not used. For static pipelines, the cores will be powered off in the device remove callback. Signed-off-by:
-
Ranjani Sridharan authored
The core_power_up/down() ops will be deprecated. Use the HDA platform-specific functions for powering up/down the cores during probe/suspend/remove. The enabled_cores_mask and the core ref_count's are manually updated in each of these functions. Signed-off-by:
-
Ranjani Sridharan authored
Free widgets for static pipelines in sof_tear_down_pipelines(). But this feature is unavailable in older firmware with ABI < 3.19. Just reset widget use_count's for this case. This would ensure that the secondary cores enabled required for topology setup are powered down properly before the primary core is powered off during system suspend. Signed-off-by:
-
Ranjani Sridharan authored
Remove the function sof_load_pipeline_ipc() and directly send the IPC instead. The pipeline core is already enabled with the call to sof_pipeline_core_enable() in sof_widget_setup(). Signed-off-by:
-
Ranjani Sridharan authored
Set core_get/put ops for CNL/ICL platforms. These platforms do not support enabling/disabling secondary cores dynamically. So skip sending the IPC to power off the cores in the core_put op. Signed-off-by:
-
Ranjani Sridharan authored
Set core_get/put() ops for TGL. When core_get() is requested for a core, its ref_count is incremented and the PM_CORE_ENABLE IPC sent to the firmware to power up the core if the current ref_count is 1. Conversely, the ref_count is decremented in core_put() and an IPC is sent to the DSP to power off the core if the ref_count is 0. Signed-off-by:
-
Ranjani Sridharan authored
Add ops to get/put a core that will be used to power up/down a core along with incrementing/decrementing its ref_count. Signed-off-by:
-
Ranjani Sridharan authored
Add two fields num_cores and dsp_cores_ref_count to struct snd_sof_dev. These will be used to maintain the ref count for each core to determine when it should be powered up or down. Signed-off-by:
-
Ranjani Sridharan authored
expose get_chip_info(). Signed-off-by:
-
Daniel Baluta authored
Resume common flow (System PM / Runtime PM) is like this: sof_resume -> specific device resume -> snd_sof_load_firmware -> snd_sof_dsp_reset (1) -> load_modules() -> snd_sof_run_firmware (2) We need to implement dsp_reset callback (1) that will actually reset the DSP but keep it stalled. In order to implement this we do the following: -> put DSP into reset (assert CoreReset bit from PWRCTL) -> stall the DSP using RunStall bit from AudioDSP_REG2 mix -> take DSP out of reset (de-assert CoreReset bit from PWRCTL) At this moment the DSP is taken out of reset and Stalled! This means that we can load the firmware and then start the DSP (2). Until now we resetted the DSP by turning down the Audiomix PD. This doesn't work for Runtime PM if another IP is keeping Audiomix PD up. By introducing dsp_reset() we no longer rely on turning off the audiomix to reset the DSP. Signed-off-by:Daniel Baluta <daniel.baluta@nxp.com> Reviewed-by:
-
Daniel Baluta authored
On i.MX8M DSP is controlled via a set of registers from Audio MIX. This patches gets a reference (via regmap) to Audio Mix registers and implements DSP start. Signed-off-by:
-
Daniel Baluta authored
We make use of common imx8m_suspend / imx8m_resume functions for both system PM and runtime PM. imx8m_suspend: - frees the MU channels - disables the clocks imx8m_resume - enables the clocks - requests the MU channels On i.MX8MP there is no dedicated functionality to put the DSP in reset. The only way of doing this is to POWER DOWN the Audiomix domain. We are able to do this because turning off the clocks and freeing the channels makes the Audiomix to have no users thus PM kernel core turns it down. SOF core will not call system PM suspend handler if the DSP is already down, but at resume it will call the system PM resume. So, we need to keep track of the state via snd_sof_dsp_set_power_state Few insights on how SOF core handles the PM: - SOF core uses PM runtime autosuspend (with a timeout of 2 secs) - at probe, SOF core boots the DSP and lets the PM runtime suspend to turn it off, if there is no activity - when someone opens the ALSA sound card (aplay/arecord, etc) ALSA core calls PM runtime resume to turn on the DSP - when the ALSA sound card is closed SOF core make use of PM subsystem to call PM runtime suspend and thus turning off the DSP. Signed-off-by:
-
Daniel Baluta authored
Handle clocks and mailbox channels at runtime suspend/resume in order to save power. DSP runtime PM uses a timeout of 2s. If device is idle for 2s system will enter runtime suspend. Because SOF state machine assumes that even if the DSP wasn't previously active at a System resume, will re-load the firmware we need to make sure that all needed resources are active. Kernel core will take care of enabling the PD, we need to make sure that we request the MU channels. Signed-off-by:
-
