The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Store rules in lists

This patch series changes the bcm-sf2 driver to keep a copy of the
inserted rules as opposed to using the HW as a storage area for a number
of reasons:

- this helps us with doing duplicate rule detection in a faster way, it
  would have required a full rule read before

- this helps with Pablo's on-going work to convert ethtool_rx_flow_spec
  to a more generic flow rule structure by having fewer code paths to
  convert to the new structure/helpers

- we need to cache copies to restore them during drive resumption,
  because depending on the low power mode the system has entered, the
  switch may have lost all of its context
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.

Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.

This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: More extack messages

Add more extack messages for several link create errors (e.g., invalid
number of queues, unknown link kind) and invalid metrics argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack arg to the nla_parse_nested calls in rtnl_newlink, and
add messages for unknown device type and link network namespace id.
In particular, it improves the failure message when the wrong link
type is used. From
    $ ip li add bond1 type bonding
    RTNETLINK answers: Operation not supported
to
    $ ip li add bond1 type bonding
    Error: Unknown device type.

(The module name is bonding but the link type is bond.)
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack argument to ip_fib_metrics_init and add messages for invalid
metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_gro_receive() compares 34 bytes using slow memcmp(),
while handcoding with a couple of ipv6_addr_equal() is much faster.

Before this patch, "perf top -e cycles:pp -C <cpu>" would
see memcmp() using ~10% of cpu cycles on a 40Gbit NIC
receiving IPv6 TCP traffic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WARN_ON() already contains an unlikely(), so it's not necessary to use
unlikely.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I started looking at the history of this driver, and last time the
maintainer was active on the mailing list was when discussing how to
remove it. This was in 2012:

https://lore.kernel.org/lkml/4F4DE175.30002@melware.de/

It looks to me like this has in practice been an orphan for quite a while.
It's throwing warnings about stack size in a function that is in dire
need of refactoring, and it's probably a case of "it's time to call it".

Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fix from Steven Rostedt:
 "Masami found a slight bug in his code where he transposed the
  arguments of a call to strpbrk.

  The reason this wasn't detected in our tests is that the only way this
  would transpire is when a kprobe event with a symbol offset is
  attached to a function that belongs to a module that isn't loaded yet.
  When the kprobe trace event is added, the offset would be truncated
  after it was parsed, and when the module is loaded, it would use the
  symbol without the offset (as the nul character added by the parsing
  would not be replaced with the original character)"

* tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Fix strpbrk() argument order

Pull ARM fix from Russell King:
 "Ard spotted a typo in one of the assembly files which leads to a
  kernel oops when that code path is executed. Fix this"

* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm

Pull networking fixes from David Miller:

 1) Handle errors mid-stream of an all dump, from Alexey Kodanev.

 2) Fix build of openvswitch with certain combinations of netfilter
    options, from Arnd Bergmann.

 3) Fix interactions between GSO and BQL, from Eric Dumazet.

 4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
    Hoffstätte.

 5) S390 qeth driver fixes from Julian Wiedmann.

 6) Allow ipv6 link local addresses for netconsole when both source and
    destination are link local, from Matwey V. Kornilov.

 7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.

 8) Initialize mutex before use in dsa microchip driver, from Tristram
    Ha.

 9) Out-of-bounds access in hns3, from Yunsheng Lin.

10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
    Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
    Neira Ayuso.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
  net: alx: make alx_drv_name static
  net: bpfilter: fix iptables failure if bpfilter_umh is disabled
  sock_diag: fix autoloading of the raw_diag module
  net: core: netpoll: Enable netconsole IPv6 link local address
  ipv6: properly check return value in inet6_dump_all()
  rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
  net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
  bonding/802.3ad: fix link_failure_count tracking
  net: phy: realtek: fix RTL8201F sysfs name
  sctp: define SCTP_SS_DEFAULT for Stream schedulers
  sctp: fix strchange_flags name for Stream Change Event
  mlxsw: spectrum: Fix IP2ME CPU policer configuration
  openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
  qed: fix link config error handling
  net: hns3: Fix for out-of-bounds access when setting pfc back pressure
  net/mlx4_en: use __netdev_tx_sent_queue()
  net: do not abort bulk send on BQL status
  net: bql: add __netdev_tx_sent_queue()
  s390/qeth: report 25Gbit link speed
  s390/qeth: sanitize ARP requests
  ...

Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.

Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:

  Internal error: Oops - undefined instruction: 0 [#1] SMP THUMB2
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc1-00030-g4d28ad89189d-dirty #488
  Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
  PC is at cpu_v7_hvc_switch_mm+0x12/0x18
  LR is at flush_old_exec+0x31b/0x570
  pc : [<c0316efe>]    lr : [<c04117c7>]    psr: 00000013
  sp : ee899e50  ip : 00000000  fp : 00000001
  r10: eda28f34  r9 : eda31800  r8 : c12470e0
  r7 : eda1fc00  r6 : eda53000  r5 : 00000000  r4 : ee88c000
  r3 : c0316eec  r2 : 00000001  r1 : eda53000  r0 : 6da6c000
  Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none

Note the 'ISA ARM' in the last line.

Fix this by using the correct name in ENDPROC().

Cc: <stable@vger.kernel.org>
Fixes: 10115105 ("ARM: spectre-v2: add firmware based hardening")
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains the first batch of Netfilter fixes for
your net tree:

1) Fix splat with IPv6 defragmenting locally generated fragments,
   from Florian Westphal.

2) Fix Incorrect check for missing attribute in nft_osf.

3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
   header, from Jiri Slaby.

4) Revert map lookup in nft_numgen, this is already possible with
   the existing infrastructure without this extension.

5) Fix wrong listing of set reference counter, make counter
   synchronous again, from Stefano Brivio.

6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.

7) Fix allocation failure with large set, use kvcalloc().
   From Andrey Ryabinin.

8) No need to disable BH when fetch ip set comment, patch from
   Jozsef Kadlecsik.

9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
   Taehee Yoo.

10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
    from Jozsef Kadlecsik.

11) Fix setting default timeout via nfnetlink_cttimeout, this
    comes with preparation patch to add nf_{tcp,udp,...}_pernet()
    helper.

12) Allow ebtables table nat to be of filter type via nft_compat.
    From Florian Westphal.

13) Incorrect calculation of next bucket in early_drop, do no bump
    hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.

test config:
   CONFIG_BPFILTER=y
   # CONFIG_BPFILTER_UMH is not set

test command:
   %iptables -L
   iptables: No chain/target/match by that name.

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.

Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: bf2ae2e4 ("sock_diag: request _diag module only when the family or proto has been registered")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no reason to discard using source link local address when
remote netconsole IPv6 address is set to be link local one.

The patch allows administrators to use IPv6 netconsole without
explicitly configuring source address:

    netconsole=@/,@fe80::5054:ff:fe2f:6012/
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.

Fixes: 08e814c9 ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.

Fix it by partially restoring the previous behavior before
commit c63586dc ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.

[1]:
unreferenced object 0xffff88001322a200 (size 96):
  comm "sshd", pid 1484, jiffies 4296032768 (age 1432.542s)
  hex dump (first 32 bytes):
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
    18 09 41 36 00 88 ff ff 18 09 41 36 00 88 ff ff  ..A6......A6....
  backtrace:
    [<0000000095846b39>] kmem_cache_alloc_trace+0x151/0x220
    [<000000007d12709f>] inet6_dump_fib+0x68d/0x940
    [<000000002775a316>] rtnl_dump_all+0x1d9/0x2d0
    [<00000000d7cd302b>] netlink_dump+0x945/0x11a0
    [<000000002f43485f>] __netlink_dump_start+0x55d/0x800
    [<00000000f76bbeec>] rtnetlink_rcv_msg+0x4fa/0xa00
    [<000000009b5761f3>] netlink_rcv_skb+0x29c/0x420
    [<0000000087a1dae1>] rtnetlink_rcv+0x15/0x20
    [<00000000691b703b>] netlink_unicast+0x4e3/0x6c0
    [<00000000b5be0204>] netlink_sendmsg+0x7f2/0xba0
    [<0000000096d2aa60>] sock_sendmsg+0xba/0xf0
    [<000000008c1b786f>] __sys_sendto+0x1e4/0x330
    [<0000000019587b3f>] __x64_sys_sendto+0xe1/0x1a0
    [<00000000071f4d56>] do_syscall_64+0x9f/0x300
    [<000000002737577f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<0000000057587684>] 0xffffffffffffffff

Fixes: c63586dc ("net: rtnl_dump_all needs to propagate error from dumpit function")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.

Fixes: 2384d025 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The __no_sanitize_address_or_inline and __no_kasan_or_inline defines
are almost identical. The only difference is that __no_kasan_or_inline
does not have the 'notrace' attribute.

To be able to replace __no_sanitize_address_or_inline with the older
definition, add 'notrace' to __no_kasan_or_inline and change to two
users of __no_sanitize_address_or_inline in the s390 code.

The 'notrace' option is necessary for e.g. the __load_psw_mask function
in arch/s390/include/asm/processor.h. Without the option it is possible
to trace __load_psw_mask which leads to kernel stack overflow.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pointed-out-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix strpbrk()'s argument order, it must pass acceptable string
in 2nd argument. Note that this can cause a kernel panic where
it recovers backup character to code->data.

Link: http://lkml.kernel.org/r/154108256792.2604.1816052586385217811.stgit@devbox

Fixes: a6682814 ("tracing/kprobes: Allow kprobe-events to record module symbol")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Commit 4d2c0cda set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.

SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.

To keep the compatibility, fix it by adding two macros.

Fixes: b444153f ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-11-03

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
   to not use page start but actual start instead to work correctly with
   profiling e.g. finding hot instructions from stack traces. Also fix latter
   with regards to dumping address and jited len for !multi prog, from Song.

2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
   instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>