- 12 Jul, 2017 19 commits
-
-
Sergei Shtylyov authored
commit 5f4c8caf upstream. All R8A7794 manuals I have here (0.50 and 1.10) agree that the PFC driver has ATAG0# and ATAWR0# signals in IPSR12 swapped -- fix this. Fixes: 43c4436e ("pinctrl: sh-pfc: add R8A7794 PFC support") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mika Westerberg authored
commit 70365027 upstream. After commit 47c950d1 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain") the driver does not add all GPIOs to the irqdomain. The reason for that is that those GPIOs cannot generate IRQs at all, only GPEs (General Purpose Events). This causes Linux virtual IRQ numbering to change. However, it seems some CYAN Chromebooks, including Acer Chromebook hardcodes these Linux IRQ numbers in the ACPI tables of the machine. Since the numbering is different now, the IRQ meant for keyboard does not match the Linux virtual IRQ number anymore making the keyboard non-functional. Work this around by adding special quirk just for these machines where we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell based machines will not be affected by the change. Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945 Fixes: 47c950d1 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain") Reported-by:
Adam S Levy <theadamlevy@gmail.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Christian Lamparter authored
commit d7402de4 upstream. This patch adds the missing PINGROUP for GPIO70-99. This fixes a crash that happens in pinctrl-msm, if any of the GPIO70-99 are accessed. Fixes: 5303f782 ("pinctrl: qcom: ipq4019: set ngpios to correct value") Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Acked-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Liping Zhang authored
commit 425fffd8 upstream. Currently, inputting the following command will succeed but actually the value will be truncated: # echo 0x12ffffffff > /proc/sys/net/ipv4/tcp_notsent_lowat This is not friendly to the user, so instead, we should report error when the value is larger than UINT_MAX. Fixes: e7d316a0 ("sysctl: handle error writing UINT_MAX to u32 fields") Signed-off-by:
Liping Zhang <zlpnobody@gmail.com> Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Liping Zhang authored
commit 5380e564 upstream. I saw some very confusing sysctl output on my system: # cat /proc/sys/net/core/xfrm_aevent_rseqth -2 # cat /proc/sys/net/core/xfrm_aevent_etime -10 # cat /proc/sys/net/ipv4/tcp_notsent_lowat -4294967295 Because we forget to set the *negp flag in proc_douintvec, so it will become a garbage value. Since the value related to proc_douintvec is always an unsigned integer, so we can set *negp to false explictily to fix this issue. Fixes: e7d316a0 ("sysctl: handle error writing UINT_MAX to u32 fields") Signed-off-by:
-
Thomas Gleixner authored
commit 8fbcfeb8 upstream. mac80211_hwsim initializes a hrtimer with clockid CLOCK_MONOTONIC_RAW. That's not supported. Use CLOCK_MONOTONIC instead. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johan Hovold authored
commit e271b2c9 upstream. Make sure to release any OF device-node reference taken when creating the USB device. Note that we currently do not hold a reference to the root hub device-tree node (i.e. the parent controller node). Fixes: 69bec725 ("USB: core: let USB device know device node") Acked-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 7cf916bd upstream. The current definition is wrong. This breaks my upcoming Aspeed virtual hub driver. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Michael Grzeschik authored
commit b3b51417 upstream. The usbip stack dynamically allocates the transfer_buffer and setup_packet of each urb that got generated by the tcp to usb stub code. As these pointers are always used only once we will set them to NULL after use. This is done likewise to the free_urb code in vudc_dev.c. This patch fixes double kfree situations where the usbip remote side added the URB_FREE_BUFFER. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Acked-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Devin Heitmueller authored
commit 6836796d upstream. The USB core and sysfs will attempt to enumerate certain parameters which are unsupported by the au0828 - causing inconsistent behavior and sometimes causing the chip to reset. Avoid making these calls. This problem manifested as intermittent cases where the au8522 would be reset on analog video startup, in particular when starting up ALSA audio streaming in parallel - the sysfs entries created by snd-usb-audio on streaming startup would result in unsupported control messages being sent during tuning which would put the chip into an unknown state. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Jeremie Rapin authored
commit fd90f73a upstream. Added the USB serial device ID for the CEL ZigBee EM3588 radio stick. Signed-off-by:
Jeremie Rapin <rapinj@gmail.com> Acked-by:
-
Felipe Balbi authored
commit 04fb365c upstream. %p will leak kernel pointers, so let's not expose the information on dmesg and instead use %pK. %pK will only show the actual addresses if explicitly enabled under /proc/sys/kernel/kptr_restrict. Acked-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Gerd Hoffmann authored
commit 385aee96 upstream. Reported-by:
李强 <liqiang6-s@360.cn> Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170406155941.458-1-kraxel@redhat.comSigned-off-by:
-
Sakari Ailus authored
commit 41387a59 upstream. There's a sanity check for the stream count remaining positive or zero on error path, but instead of performing the check on the traversed entity it is performed on the entity where traversal ends. Fix this. Fixes: commit 3801bc7d ("[media] media: Media Controller fix to not let stream_count go negative") Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Sabrina Dubroca authored
commit 9e52b325 upstream. Always try to parse an address, since kstrtoul() will safely fail when given a symbol as input. If that fails (which will be the case for a symbol), try to parse a symbol instead. This allows creating a probe such as: p:probe/vlan_gro_receive 8021q:vlan_gro_receive+0 Which is necessary for this command to work: perf probe -m 8021q -a vlan_gro_receive Link: http://lkml.kernel.org/r/fd72d666f45b114e2c5b9cf7e27b91de1ec966f1.1498122881.git.sd@queasysnail.net Fixes: 413d37d1 ("tracing: Add kprobe-based event tracer") Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Yan, Zheng authored
commit b50c2de5 upstream. The dirfragtree is lazily updated, it's not always accurate. Infinite loops happens in following circumstance. - client send request to read frag A - frag A has been fragmented into frag B and C. So mds fills the reply with contents of frag B - client wants to read next frag C. ceph_choose_frag(frag value of C) return frag A. The fix is using previous readdir reply to calculate next readdir frag when possible. Signed-off-by:
"Yan, Zheng" <zyan@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Adrian Salido authored
commit 62655397 upstream. The driver_override implementation is susceptible to race condition when different threads are reading vs storing a different driver override. Add locking to avoid race condition. Fixes: 3d713e0e ("driver core: platform: add device binding path 'driver_override'") Cc: stable@vger.kernel.org Signed-off-by:
Adrian Salido <salidoa@google.com> Signed-off-by:
-
Christoph Hellwig authored
commit 629e014b upstream. Currently we just stash anything we got into file->f_flags, and the report it in fcntl(F_GETFD). This patch just clears out all unknown flags so that we don't pass them to the fs or report them. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Christoph Hellwig authored
commit 80f18379 upstream. Add a central define for all valid open flags, and use it in the uniqueness check. Signed-off-by:
-
- 05 Jul, 2017 21 commits
-
-
Greg Kroah-Hartman authored
-
Wanpeng Li authored
commit d4912215 upstream. WARNING: CPU: 3 PID: 2840 at arch/x86/kvm/vmx.c:10966 nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel] CPU: 3 PID: 2840 Comm: qemu-system-x86 Tainted: G OE 4.12.0-rc3+ #23 RIP: 0010:nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel] Call Trace: ? kvm_check_async_pf_completion+0xef/0x120 [kvm] ? rcu_read_lock_sched_held+0x79/0x80 vmx_queue_exception+0x104/0x160 [kvm_intel] ? vmx_queue_exception+0x104/0x160 [kvm_intel] kvm_arch_vcpu_ioctl_run+0x1171/0x1ce0 [kvm] ? kvm_arch_vcpu_load+0x47/0x240 [kvm] ? kvm_arch_vcpu_load+0x62/0x240 [kvm] kvm_vcpu_ioctl+0x384/0x7b0 [kvm] ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm] ? __fget+0xf3/0x210 do_vfs_ioctl+0xa4/0x700 ? __fget+0x114/0x210 SyS_ioctl+0x79/0x90 do_syscall_64+0x81/0x220 entry_SYSCALL64_slow_path+0x25/0x25 This is triggered occasionally by running both win7 and win2016 in L2, in addition, EPT is disabled on both L1 and L2. It can't be reproduced easily. Commit 0b6ac343 (KVM: nVMX: Correct handling of exception injection) mentioned that "KVM wants to inject page-faults which it got to the guest. This function assumes it is called with the exit reason in vmcs02 being a #PF exception". Commit e011c663 (KVM: nVMX: Check all exceptions for intercept during delivery to L2) allows to check all exceptions for intercept during delivery to L2. However, there is no guarantee the exit reason is exception currently, when there is an external interrupt occurred on host, maybe a time interrupt for host which should not be injected to guest, and somewhere queues an exception, then the function nested_vmx_check_exception() will be called and the vmexit emulation codes will try to emulate the "Acknowledge interrupt on exit" behavior, the warning is triggered. Reusing the exit reason from the L2->L0 vmexit is wrong in this case, the reason must always be EXCEPTION_NMI when injecting an exception into L1 as a nested vmexit. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Fixes: e011c663 ("KVM: nVMX: Check all exceptions for intercept during delivery to L2") Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Radim Krčmář authored
commit f0367ee1 upstream. Static checker noticed that base3 could be used uninitialized if the segment was not present (useable). Random stack values probably would not pass VMCS entry checks. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Fixes: 1aa36616 ("KVM: x86 emulator: consolidate segment accessors") Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Reviewed-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
-
Radim Krčmář authored
commit 34b0dadb upstream. Static analysis noticed that pmu->nr_arch_gp_counters can be 32 (INTEL_PMC_MAX_GENERIC) and therefore cannot be used to shift 'int'. I didn't add BUILD_BUG_ON for it as we have a better checker. Reported-by:
-
Ladi Prosek authored
commit 6ed071f0 upstream. On AMD, the effect of set_nmi_mask called by emulate_iret_real and em_rsm on hflags is reverted later on in x86_emulate_instruction where hflags are overwritten with ctxt->emul_flags (the kvm_set_hflags call). This manifests as a hang when rebooting Windows VMs with QEMU, OVMF, and >1 vcpu. Instead of trying to merge ctxt->emul_flags into vcpu->arch.hflags after an instruction is emulated, this commit deletes emul_flags altogether and makes the emulator access vcpu->arch.hflags using two new accessors. This way all changes, on the emulator side as well as in functions called from the emulator and accessing vcpu state with emul_to_vcpu, are preserved. More details on the bug and its manifestation with Windows and OVMF: It's a KVM bug in the interaction between SMI/SMM and NMI, specific to AMD. I believe that the SMM part explains why we started seeing this only with OVMF. KVM masks and unmasks NMI when entering and leaving SMM. When KVM emulates the RSM instruction in em_rsm, the set_nmi_mask call doesn't stick because later on in x86_emulate_instruction we overwrite arch.hflags with ctxt->emul_flags, effectively reverting the effect of the set_nmi_mask call. The AMD-specific hflag of interest here is HF_NMI_MASK. When rebooting the system, Windows sends an NMI IPI to all but the current cpu to shut them down. Only after all of them are parked in HLT will the initiating cpu finish the restart. If NMI is masked, other cpus never get the memo and the initiating cpu spins forever, waiting for hal!HalpInterruptProcessorsStarted to drop. That's the symptom we observe. Fixes: a584539b ("KVM: x86: pass the whole hflags field to emulator and back") Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
-
Mark Salter authored
commit 335d2c2d upstream. Commit 5c492c3f ("arm64: smp: Add function to determine if cpus are stuck in the kernel") added a helper function to determine if die() is supported in cpu_ops. This function assumes a cpu will have a valid cpu_ops entry, but that may not be the case for cpu0 is spin-table or parking protocol is used to boot secondary cpus. In that case, there is a NULL dereference if have_cpu_die() is called by cpu0. So add a check for a valid cpu_ops before dereferencing it. Fixes: 5c492c3f ("arm64: smp: Add function to determine if cpus are stuck in the kernel") Signed-off-by:
Mark Salter <msalter@redhat.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Kamal Dasu authored
commit 9d2ee0a6 upstream. On brcmnand controller v6.x and v7.x, the #WP pin is controlled through the NAND_WP bit in CS_SELECT register. The driver currently assumes that toggling the #WP pin is instantaneously enabling/disabling write-protection, but it actually takes some time to propagate the new state to the internal NAND chip logic. This behavior is sometime causing data corruptions when an erase/program operation is executed before write-protection has really been disabled. Fixes: 27c5b17c ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by:
Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Jaedon Shin authored
commit 2de3ec4f upstream. The BSC data buffers to send and receive data are each of size 32 bytes or 8 bytes 'xfersz' depending on SoC. The problem observed for all the combined message transfer was if length of data transfer was a multiple of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed this by appropriately setting START/STOP conditions for such transfers. Fixes: dd1aa252 ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver") Signed-off-by:
Jaedon Shin <jaedon.shin@gmail.com> Acked-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Rafał Miłecki authored
commit 77c0d0cd upstream. Our code was assigning number of channels to the index variable by default. If firmware reported channel we didn't predict this would result in using that initial index value and writing out of array. This never happened so far (we got a complete list of supported channels) but it means possible memory corruption so we should handle it anyway. This patch simply detects unexpected channel and ignores it. As we don't try to create new entry now, it's also safe to drop hw_value and center_freq assignment. For known channels we have these set anyway. I decided to fix this issue by assigning NULL or a target channel to the channel variable. This was one of possible ways, I prefefred this one as it also avoids using channel[index] over and over. Fixes: 58de92d2 ("brcmfmac: use static superset of channels for wiphy bands") Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Arnd Bergmann authored
commit 5b0ff9a0 upstream. hns_roce_v1_cq_set_ci() calls roce_set_bit() on an uninitialized field, which will then change only a few of its bits, causing a warning with the latest gcc: infiniband/hw/hns/hns_roce_hw_v1.c: In function 'hns_roce_v1_cq_set_ci': infiniband/hw/hns/hns_roce_hw_v1.c:1854:23: error: 'doorbell[1]' is used uninitialized in this function [-Werror=uninitialized] roce_set_bit(doorbell[1], ROCEE_DB_OTHERS_H_ROCEE_DB_OTH_HW_SYNS_S, 1); The code is actually correct since we always set all bits of the port_vlan field, but gcc correctly points out that the first access does contain uninitialized data. This initializes the field to zero first before setting the individual bits. Fixes: 9a443537 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 5c51f4ae upstream. Arnd Bergmann reported a (false positive) objtool warning: drivers/infiniband/sw/rxe/rxe_resp.o: warning: objtool: rxe_responder()+0xfe: sibling call from callable instruction with changed frame pointer The issue is in find_switch_table(). It tries to find a switch statement's jump table by walking backwards from an indirect jump instruction, looking for a relocation to the .rodata section. In this case it stopped walking prematurely: the first .rodata relocation it encountered was for a variable (resp_state_name) instead of a jump table, so it just assumed there wasn't a jump table. The fix is to ignore any .rodata relocation which refers to an ELF object symbol. This works because the jump tables are anonymous and have no symbols associated with them. Reported-by:
Josh Poimboeuf <jpoimboe@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 3732710f ("objtool: Improve rare switch jump table pattern detection") Link: http://lkml.kernel.org/r/20170302225723.3ndbsnl4hkqbne7a@trebleSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sudeep Holla authored
commit 67bcc2c5 upstream. Currently we add the virtual cpufreq device unconditionally even when the SCPI DVFS clock provider node is disabled. This will cause cpufreq driver to throw errors when it gets initailised on boot/modprobe and also when the CPUs are hot-plugged back in. This patch fixes the issue by adding the virtual cpufreq device only if the SCPI DVFS clock provider is available and registered. Fixes: 9490f01e ("clk: scpi: add support for cpufreq virtual device") Reported-by:
Michał Zegan <webczat_200@poczta.onet.pl> Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Sudeep Holla <sudeep.holla@arm.com> Tested-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Dan Carpenter authored
commit a69261e4 upstream. The "goto err_armclk;" error path already does a clk_put(s3c_freq->hclk); so this is a double free. Fixes: 34ee5507 ([CPUFREQ] Add S3C2416/S3C2450 cpufreq driver) Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Suravee Suthikulpanit authored
commit 84a21dbd upstream. Pass-through devices to VM guest can get updated IRQ affinity information via irq_set_affinity() when not running in guest mode. Currently, AMD IOMMU driver in GA mode ignores the updated information if the pass-through device is setup to use vAPIC regardless of guest_mode. This could cause invalid interrupt remapping. Also, the guest_mode bit should be set and cleared only when SVM updates posted-interrupt interrupt remapping information. Signed-off-by:
Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Cc: Joerg Roedel <jroedel@suse.de> Fixes: d98de49a ('iommu/amd: Enable vAPIC interrupt remapping mode by default') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Pan Bian authored
commit 73dbd4a4 upstream. In function amd_iommu_bind_pasid(), the control flow jumps to label out_free when pasid_state->mm and mm is NULL. And mmput(mm) is called. In function mmput(mm), mm is referenced without validation. This will result in a NULL dereference bug. This patch fixes the bug. Signed-off-by:
Pan Bian <bianpan2016@163.com> Fixes: f0aac63b ('iommu/amd: Don't hold a reference to mm_struct') Signed-off-by:
-
Robin Murphy authored
commit 938f1bbe upstream. Even if a host controller's CPU-side MMIO windows into PCI I/O space do happen to leak into PCI memory space such that it might treat them as peer addresses, trying to reserve the corresponding I/O space addresses doesn't do anything to help solve that problem. Stop doing a silly thing. Fixes: fade1ec0 ("iommu/dma: Avoid PCI host bridge windows") Reviewed-by:
Eric Auger <eric.auger@redhat.com> Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
-
Robin Murphy authored
commit 797a8b4d upstream. We wouldn't normally expect ops->attach_dev() to fail, but on IOMMUs with limited hardware resources, or generally misconfigured systems, it is certainly possible. We report failure correctly from the external iommu_attach_device() interface, but do not do so in iommu_group_add() when attaching to the default domain. The result of failure there is that the device, group and domain all get left in a broken, part-configured state which leads to weird errors and misbehaviour down the line when IOMMU API calls sort-of-but-don't-quite work. Check the return value of __iommu_attach_device() on the default domain, and refactor the error handling paths to cope with its failure and clean up correctly in such cases. Fixes: e39cb8a3 ("iommu: Make sure a device is always attached to a domain") Reported-by:
Punit Agrawal <punit.agrawal@arm.com> Signed-off-by:
-
David Dillow authored
commit f7116e11 upstream. dma_pte_free_level() recurses down the IOMMU page tables and frees directory pages that are entirely contained in the given PFN range. Unfortunately, it incorrectly calculates the starting address covered by the PTE under consideration, which can lead to it clearing an entry that is still in use. This occurs if we have a scatterlist with an entry that has a length greater than 1026 MB and is aligned to 2 MB for both the IOMMU and physical addresses. For example, if __domain_mapping() is asked to map a two-entry scatterlist with 2 MB and 1028 MB segments to PFN 0xffff80000, it will ask if dma_pte_free_pagetable() is asked to PFNs from 0xffff80200 to 0xffffc05ff, it will also incorrectly clear the PFNs from 0xffff80000 to 0xffff801ff because of this issue. The current code will set level_pfn to 0xffff80200, and 0xffff80200-0xffffc01ff fits inside the range being cleared. Properly setting the level_pfn for the current level under consideration catches that this PTE is outside of the range being cleared. This patch also changes the value passed into dma_pte_free_level() when it recurses. This only affects the first PTE of the range being cleared, and is handled by the existing code that ensures we start our cursor no lower than start_pfn. This was found when using dma_map_sg() to map large chunks of contiguous memory, which immediatedly led to faults on the first access of the erroneously-deleted mappings. Fixes: 3269ee0b ("intel-iommu: Fix leaks in pagetable freeing") Reviewed-by:
Benjamin Serebrin <serebrin@google.com> Signed-off-by:
David Dillow <dillow@google.com> Signed-off-by:
-
Junxiao Bi authored
commit 33496c3c upstream. Configfs is the interface for ocfs2-tools to set configure to kernel and $configfs_dir/cluster/$clustername/heartbeat/dead_threshold is the one used to configure heartbeat dead threshold. Kernel has a default value of it but user can set O2CB_HEARTBEAT_THRESHOLD in /etc/sysconfig/o2cb to override it. Commit 45b99773 ("ocfs2/cluster: use per-attribute show and store methods") changed heartbeat dead threshold name while ocfs2-tools did not, so ocfs2-tools won't set this configurable and the default value is always used. So revert it. Fixes: 45b99773 ("ocfs2/cluster: use per-attribute show and store methods") Link: http://lkml.kernel.org/r/1490665245-15374-1-git-send-email-junxiao.bi@oracle.comSigned-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Acked-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Andy Lutomirski authored
commit dbd68d8e upstream. flush_tlb_page() passes a bogus range to flush_tlb_others() and expects the latter to fix it up. native_flush_tlb_others() has the fixup but Xen's version doesn't. Move the fixup to flush_tlb_others(). AFAICS the only real effect is that, without this fix, Xen would flush everything instead of just the one page on remote vCPUs in when flush_tlb_page() was called. Signed-off-by:
Andy Lutomirski <luto@kernel.org> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: e7b52ffd ("x86/flush_tlb: try flush_tlb_single one by one in flush_tlb_range") Link: http://lkml.kernel.org/r/10ed0e4dfea64daef10b87fb85df1746999b4dba.1492844372.git.luto@kernel.orgSigned-off-by:
-
Joerg Roedel authored
commit 5ed386ec upstream. When this function fails it just sends a SIGSEGV signal to user-space using force_sig(). This signal is missing essential information about the cause, e.g. the trap_nr or an error code. Fix this by propagating the error to the only caller of mpx_handle_bd_fault(), do_bounds(), which sends the correct SIGSEGV signal to the process. Signed-off-by:
-
