Among the changes are new CoS discard counters and new ctx_hw_stats_ext
struct for the latest 5750X B0 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 60649d4e ("can: remove obsolete empty ioctl() handler") replaced the
almost empty can_ioctl() function with sock_no_ioctl() which always returns
-EOPNOTSUPP.

Even though we don't have any ioctl() functions on socket/network layer we need
to return -ENOIOCTLCMD to be able to forward ioctl commands like SIOCGIFINDEX
to the network driver layer.

This patch fixes the wrong return codes in the CAN network layer protocols.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 60649d4e ("can: remove obsolete empty ioctl() handler")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have an ERPS (Ethernet Ring Protection Switching) setup involving
mv88e6250 switches which we're in the process of switching to a BSP
based on the mainline driver. Breaking any link in the ring works as
expected, with the ring reconfiguring itself quickly and traffic
continuing with almost no noticable drops. However, when plugging back
the cable, we see 5+ second stalls.

This has been tracked down to the userspace application in charge of
the protocol missing a few CCM messages on the good link (the one that
was not unplugged), causing it to broadcast a "signal fail". That
message eventually reaches its link partner, which responds by
blocking the port. Meanwhile, the first node has continued to block
the port with the just plugged-in cable, breaking the network. And the
reason for those missing CCM messages has in turn been tracked down to
the VTU apparently being too busy servicing load/purge operations that
the normal lookups are delayed.

Initial state, the link between C and D is blocked in software.

     _____________________
    /                     \
   |                       |
   A ----- B ----- C *---- D

Unplug the cable between C and D.

     _____________________
    /                     \
   |                       |
   A ----- B ----- C *   * D

Reestablish the link between C and D.
     _____________________
    /                     \
   |                       |
   A ----- B ----- C *---- D

Somehow, enough VTU/ATU operations happen inside C that prevents
the application from receving the CCM messages from B in a timely
manner, so a Signal Fail message is sent by C. When B receives
that, it responds by blocking its port.

     _____________________
    /                     \
   |                       |
   A ----- B *---* C *---- D

Very shortly after this, the signal fail condition clears on the
BC link (some CCM messages finally make it through), so C
unblocks the port. However, a guard timer inside B prevents it
from removing the blocking before 5 seconds have elapsed.

It is not unlikely that our userspace ERPS implementation could be
smarter and/or is simply buggy. However, this patch fixes the symptoms
we see, and is a small optimization that should not break anything
(knock wood). The idea is simply to avoid doing an VTU load of an
entry identical to the one already present. To do that, we need to
know whether mv88e6xxx_vtu_get() actually found an existing entry, or
has just prepared a struct mv88e6xxx_vtu_entry for us to load. To that
end, let vlan->valid be an output parameter. The other two callers of
mv88e6xxx_vtu_get() are not affected by this patch since they pass
new=false.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a previous attempt to use xmit_more, but the change had to be
reverted because under load sometimes a transmit timeout occurred [0].
Maybe this was caused by a missing memory barrier, the new attempt
keeps the memory barrier before the call to netif_stop_queue like it
is used by the driver as of today. The new attempt also changes the
order of some calls as suggested by Eric.

[0] https://lkml.org/lkml/2019/2/10/39Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add compile test support by moving all includes of files under
asm/octeon into octeon-ethernet.h, and if we're not on MIPS,
stub out all the calls into the octeon support code in octeon-stubs.h
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

use resource_size to calcuate ioremap size and make
the code simpler.
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Shevchenko says:

====================
NFC: nxp-nci: clean up and new device support

Few people reported that some laptops are coming with new ACPI ID for the
devices should be supported by nxp-nci driver.

This series adds new ID (patch 2), cleans up the driver from legacy platform
data and unifies GPIO request for Device Tree and ACPI (patches 3-6), removes
dead or unneeded code (patches 7, 9, 11), constifies ID table (patch 8),
removes comma in terminator line for better maintenance (patch 10) and
rectifies Kconfig entry (patches 12-14).

It also contains a fix for NFC subsystem as suggested by Sedat.

Series has been tested by Sedat.

Changelog v4:
- rebased on top of latest linux-next
- appended cover letter
- elaborated removal of pr_fmt() in the patch 11 (David)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a simple cleanup to the Kconfig help text as discussed in [1].

[1] https://marc.info/?t=155774435600001&r=1&w=2Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch clarifies on the supported NXP NCI chips and families
and lists PN547 and PN548 separately which are known as NPC100
respectively NPC300.

This helps to find informations and identify drivers on vendor's
support websites.

For details see the discussion in [1] and [2].

[1] https://marc.info/?t=155774435600001&r=1&w=2
[2] https://patchwork.kernel.org/project/linux-wireless/list/?submitter=33142Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems contributors follow the style of Kconfig entries where explicit
'default n' is present.  The default 'default' is 'n' already, thus, drop
these lines from Kconfig to make it more clear.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macro had never been used.

The driver uses mostly the nfc_err(), which, with other macros in the family,
is backed by corresponding dev_err(). pr_fmt() is not used for dev_err()
macro. Moreover, there is no need to print the module name which is part of the
device instance name anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to have a comma after terminator entry
in the arrays of IDs.

This may prevent the misguided addition behind the terminator
without compiler notice.

Drop the comma in terminator lines for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to guard OF device ID table with of_match_ptr().
Otherwise we would get a defined but not used data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The content of acpi_device_id is not supposed to change at runtime.
All functions working with acpi_device_id provided by <linux/acpi.h>
work with const acpi_device_id. So mark the non-const structs as const.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return directly in ->probe() since there no special cleaning is needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to unify GPIO resource request prepare gpiod_get_index()
to behave correctly when there is no mapping provided by firmware.

Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we got rid of platform data, the driver may use
GPIO descriptor directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.

If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems a lot of laptops are equipped with NXP NFC300 chip with
the ACPI ID NXP1001 as per DSDT.

Append it to the driver's ACPI ID table.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfc_genl_deactivate_target() relies on the NFC_ATTR_TARGET_INDEX
attribute being present, but doesn't check whether it is actually
provided by the user. Same goes for nfc_genl_fw_download() and
NFC_ATTR_FIRMWARE_NAME.

This patch adds appropriate checks.

Found with syzkaller.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: some code optimizations & bugfixes & features

This patch-set includes code optimizations, bugfixes and features for
the HNS3 ethernet controller driver.

[patch 1/10] checks reset status before setting channel.

[patch 2/10] adds a NULL pointer checking.

[patch 3/10] removes reset level upgrading when current reset fails.

[patch 4/10] fixes a GFP flags errors when holding spin_lock.

[patch 5/10] modifies firmware version format.

[patch 6/10] adds some print information which is off by default.

[patch 7/10 - 8/10] adds two code optimizations about interrupt handler
and work task.

[patch 9/10] adds support for using order 1 pages with a 4K buffer.

[patch 10/10] modifies messages prints with dev_info() instead of
pr_info().

Change log:
V3->V4: replace netif_info with netif_dbg in [patch 6/10]
V2->V3: fixes comments from Saeed Mahameed and Joe Perches.
V1->V2: fixes comments from Saeed Mahameed and
	removes previous [patch 4/11] and [patch 11/11]
	which needs further discussion, and adds a new
	patch [10/10] suggested by Saeed Mahameed.
====================
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev_info() is more appropriate for printing messages when driver
initialization done, so switch to dev_info().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware supports 0.5K, 1K, 2K, 4K RX buffer size, the
RX buffer can not be reused because the hns3_page_order
return 0 when page size and RX buffer size are both 4096.

So this patch changes the hns3_page_order to return 1 when
RX buffer is greater than half of the page size and page size
is less the 8192, and dev_alloc_pages has already been used
to allocate the compound page for RX buffer.

This patch also changes hnae3_* to hns3_* for page order
and RX buffer size calculation because they are used in
hns3 module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.

This patch sets the above three subtask's affinity using the
misc interrupt' affinity.

Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use delayed work instead of using timers to trigger the
hclge_serive.

Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some times just see the eth interface have been down/up via
dmesg, but can not know why the eth down. So adds some debug
messages to identify the cause for this.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies firmware version display format in
hclge(vf)_cmd_init() and hns3_get_drvinfo(). Also, adds
some optimizations for firmware version display format.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When allocating memory, the GFP_KERNEL cannot be used during the
spin_lock period. This is because it may cause scheduling when holding
spin_lock. This patch changes GFP flag to GFP_ATOMIC in this case.

Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: lipeng 00277521 <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, hclge_reset_err_handle() will assert a global reset
when the failing count is smaller than MAX_RESET_FAIL_CNT, which
will affect other running functions.

So this patch removes this upgrading, and uses re-scheduling reset
task to do it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some cases, ops->get_reset_level may not be implemented, so we
should check whether it is NULL before calling get_reset_level.
Signed-off-by: Guangbin Huang <huangguangbin@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hns3_set_channels() should check the resetting status firstly,
since the device will reinitialize when resetting. If the
reset has not completed, the hns3_set_channels() may access
invalid memory.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_acl: Forbid unsupported filters

Patches #1-#2 make mlxsw reject unsupported egress filters. These
include filters that match on VLAN and filters associated with a
redirect action. Patch #1 rejects such filters when they are configured
on egress and patch #2 rejects such filters when they are configured in
a shared block that user tries to bind to egress.

Patch #3 forbids matching on reserved TCP flags as this is not supported
by the current keys that mlxsw uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Matching on reserved TCP flags bits is only supported using custom
parser. Since the usecase for that is not known now, just forbid to
offload rules that match on these bits.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some matches and actions are not supported on egress. Track such rules
and forbid a bind of block which contains them to egress.

With this patch, the kernel tells the user he cannot do that:
$ tc qdisc add dev ens16np1 ingress_block 22 clsact
$ tc filter add block 22 protocol 802.1q pref 2 handle 101 flower vlan_id 100 skip_sw action pass
$ tc qdisc add dev ens16np2 egress_block 22 clsact
Error: mlxsw_spectrum: Block cannot be bound to egress because it contains unsupported rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum ASIC does not support redirection on egress, so refuse to
insert such flows:

$ tc qdisc add dev ens16np1 clsact
$ tc filter add dev ens16np1 egress protocol all pref 1 handle 101 flower skip_sw action mirred egress redirect dev ens16np2
Error: mlxsw_spectrum: Redirect action is not supported on egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: improve HW csum and TSO handling

This series:
- delegates more tasks from the driver to the core
- enables HW csum and TSO per default
- copies quirks for buggy chip versions from vendor driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable HW csum and TSO per default except on known buggy chip versions.
Realtek confirmed that RTL8168evl has a HW issue with TSO.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The loop in r8169_csum_workaround is called only if in
msdn_giant_send_check a copy of the skb header needs to be made and
we don't have enough memory. Let's simply drop the packet in that case
so that we can remove r8169_csum_workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement callback ndo_features_check and move all feature checks there.
This will allow us to get rid of r8169_csum_workaround() completely in
a subsequent step. Like in the vendor driver disable HW csum for short
packets on RTL8168b.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>