Merge branch 'next-samsung-devupdates2' into next-samsung

The S3C64XX SoC series support 12bit ADC data, enable this and
mask the data accordingly.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Making the code depend on CONFIG_SND_S3C24XX_SOC means that if the ASoC
code is build modularily, the boards will fail to link due to the device
code also being built as a module.

As per Mark Brown's suggestions, just compile this always as it is expected
many machines will have audio.

Also move the obj-y line out of the device setup area into a new area just
for devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

As part of the development process, it is hoped PLAT_S3C is either removed
from all of the PLAT_SAMSUNG derived platforms or removed entirely. It is
also better to use PLAT_SAMSUNG as this is the current base of all Samsung
devices.

Change the two places that use PLAT_S3C to use PLAT_SAMSUNG
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add SERIAL_SAMSUNG_UARTS_4 to mop up the number of cases currently using
four Samsung compatible UARTS.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The S3C2412 has a fractional baud rate register, this patch adds the
corresponding flag to the UART definition to allow generation of more
precise baud rates for the various clock combinations.
Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The SPI controller platform devices should be compiled in
independent of the driver support, otherwise we might end
up with dev-spi built as kernel module.
Change this to make every machine select if it has some SPI
device and wants to build device definitions.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the required DMA masks to the hs-otg device definition to allow DMA
to work with it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Currently, S5P_TIMER_IRQ is based at the end of VICs. This patch changes
the S5P_TIMER_IRQ base from end of VICs to 11 in ISA IRQ space.
No of VICs varies between SOCs. This causes an exception on S5P6442.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1. Moved common memory map definitions for S5P such as S5P_VA_XXX
   into plat-s5p/include/mach/map-s5p.h from mach-s5p6440/include/mach.
2. Removed unnecessary definitions in the map.h and irq.c
3. Removed the unnecessary support for unaligned UART address
4. Renamed S5P_VA_VICx definitions as VA_VICx
5. Moved the definitons of VIC_BASE to plat-s5p/include/plat/irqs.h
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The s5p6440-clock.c and s5p6440-init.c code in the plat-s5p is specific to
s5p6440 SoC based systems. So these files are being moved to the machine
directory of s5p6440. And these files are renamed in the machine directory.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Merge branch 'next-smdk6410-defconfig' into next-samsung

Add an error print to s3c24xx_register_clocks to provide more useful
information when failing to register the clock.

I belive this was originally left out due to the possibility of a
problem with low-level debugging code. However, if the low-level
debug code is not functional by now there will be a whole other set of
problems being presented to the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add some kerneldoc documentation to the s3c24xx_register_clock and the
s3c24xx_register_clocks() call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Functions should be marked __init, not __initdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

ARM: SAMSUNG: Fix null pointer dereference in ADC driver

Use struct adc_device instead of relying on client (which could be
NULL) when checking for SoC type.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch adds UART serial port support for S5PV210.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the HSOTG and HSMMC block addresses to the map.h file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Update the s3c6400_defconfig with one from the current kernel which has been
build and run tested on an SMDK6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The Samsung initrd for SMDK6410 is now bigger than the original initrds
that where used. Increase the command-line size and the size of the ramdisk
that it is unpacked into.

Also change the default init to /linuxrc to avoid problems with the current
SMDK ramdisk image failing to run /bin/bash.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The s3c64xx_spi_set_info() sets one of two platform data structures depending
on which controller is being specified. Change to taking a pointer to the
relevant platform data structure and then having one set of code to place
the data into the area being pointed to.

Cc: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

ARM: S3C64XX: Fix typo in s3c-hsotg platform data
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

They are not exported, they are referenced via vtables.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

It's not exported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

As reported when the patch was posted commit 71269364 ("ARM: S3C64XX:
Add I2S resources in platform code") uses pin names for the IISv4
data output pins which are not present in mainline, causing dev-audio
to fail to build. Fix this by using the defines which are actually
present in the kernel source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The WM835x driver won't actually use this yet but it will in the
future when the changes converting it to genirq are merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the pm-check.c file to plat-samsung for all Samsung SoC users, and
update Kconfig names to make them SAMSUNG_ instead of S3C2410_

Sed expresions used to make the change:

    s/S3C2410_PM_DEBUG/SAMSUNG_PM_DEBUG/g
    s/S3C2410_PM_CHECK/SAMSUNG_PM_CHECK/g
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the PWM driver support to plat-samsung, as these PWM blocks are
close enough across the current range to be supported by this driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move header files which are not likely to be touched in
any further support addition out of plat-s3c's include
directory into plat-samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Merge branch 'next-samsung-s5p6440-iodec' into next-samsung-try10

Start Documentation/arm/Samsung and add an initial overview file
which whilst is not complete, is better than nothing.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch adds the IO descriptor for ChipID block in S5P6440.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Rename mach-s3c2410/include/mach/gpio-core.h to mach/gpio-track.h so that
it can be included by <plat/gpio-core.h> when needed.

Eliminate all other empty gpio-core.h files and just include the
<plat/gpio-core.h> as necessary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the GPIO and GPIO configuration headers into arch/arm/plat-samsung
as they are common to all the Samsung SoCs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the gpio.c code containing the core gpiolib and GPIO support to
plat-samsung from plat-s3c as it is used by all current Samsung SoCs.

Note, we didn't move this to gpiolib.c as it contains code that is not
strictly for gpiolib support and the 4bit code is already called gpiolib.c
so make the change easier by not renaming both files in one go.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the pm-gpio code into plat-samsung.

Note, this should be changed later to properly compile the 4bit code if
the 4bit settings are enabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch adds Samsung's S5P6440 GPIO support.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch moves GPIO common functions (from plat-s3c64xx) into plat-samsung.
and adds the config option to build the plat-samsung/gpiolib for Samsung SoCs.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Merge branch 'next-samsung-serial1' into next-samsung-try7

Merge branch 'next-samsung-clock2' into next-samsung-try7