When rotating 90/270 + mirroring with YUV422, the end result will have
adjacent pixels swapped. The problem is that
dispc_ovl_set_rotation_attrs() has wrong rotation values for these
cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

TILER rotation with YUV422 pixelformats does not work at the moment. All
other pixel formats work, because the pixelformat's pixel size is equal
to tiler unit size (e.g. XR24's pixel size is 32 bits, and the TILER
unit size that has to be used is 32 bits).

For YUV422 formats this is not the case, as the TILER unit size has to
be 32 bits, but the pixel size is 16 bits. The end result is OCP errors
and sync losts.

This patch adds the code to adjust the variables for YUV422 formats.

We could make the code more generic by passing around the pixel format,
rotation type, angle and the tiler unit size, which would allow us to do
calculations without special case for YUV422. However, this would make
the code more complex, and at least for now this is much more easier to
handle with these two special cases for YUV422.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The omapdrm driver has not passed the rotation value to the dispc
driver. This doesn't affect RGB formats, but YUV formats don't work
without dispc knowing the orientation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Change dispc driver to use the DRM_MODE_REFLECT flags instead of a mirror
boolean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

At the moment the dispc driver uses a custom enum for rotation. Change
it to use the DRM's DRM_MODE_ROTATE_*.

Note that mirroring is at the moment handled as a separate boolean in
the dispc driver, so we only use the DRM_MODE_ROTATE_* values.

Note, DSS HW uses clockwise rotation, DRM counter-clockwise.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

struct omap_drm_window is only used to pass plane setup data to
omap_framebuffer_update_scanout(). This can as well be accomplished by
just passing the DRM state.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Add a helper function to convert DRM rotation to TILER rotation.

Also drop a error print that can never happen, as the DRM framework
makes sure the rotation is valid.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Now that we use fourccs, we can also rename the 'color_mode' variables
to 'fourcc'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

omap_fb.c has a table with DSS and DRM formats, used to convert between
them. This is no longer needed, so we can change the array to a plain
array of DRM_FORMAT_* values which contain all possible pixel formats
supported by any DSS IP version.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We now get a fourcc array from dispc when asking for a plane's supported
pixel formats, so we can drop omap_framebuffer_get_formats() which was
used to convert between DSS and DRM pixel formats.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

This patch changes omapdrm to use DRM_FORMAT_* values instead of
OMAP_DSS_COLOR_* enum.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

In this step we drop 'enum omap_color_mode', and use u32 instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

enum omap_color_mode is a bitmask, so at the moment we present the
supported color modes as mask. To be able to move to fourccs, we need to
use an array to present the supported color modes.

As a first step towards fourccs, this patch changes the code to use an
array to store the enums.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss.h contains prototypes for three functions, which are also
defined in dss_features.h. Remove the extra prototypes from omapdss.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

In a few places the dispc driver needs to know whether the pixel format
is an YUV format. Add a helper to figure that out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code to calculate offset in dispc's calc_offset() is overly complex.
Simplify it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We have three rotation methods supported by the SoCs with DSS: DMA,
VRFB and TILER.

DMA rotation works in theory on all DSS platforms, but in practice it's
unusable due to the huge amount of memory bandwidth it uses, and has
never really been used.

VRFB is available on OMAP3, but is not supported by omapdrm, even though
we have some code for it in the dispc driver.

TILER is supported on OMAP4/OMAP5/DRA7/AM5 platforms, but has some
driver bugs.

To clean up the driver to help fixing the TILER issues, this patch drops
the DMA and VRFB rotation support, leaving only TILER rotation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Use dev_err_ratelimited() when an OCP error happens, to slightly easen
the flood.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

DSS IP versions 2 and 3 support CLUT modes (color lookup table), but the
driver has never supported those. We still have had some code for CLUT
modes. As the newer DSS IP versions have dropped CLUT support, we might
as well clean up the driver by removing the CLUT related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code that sets and clears DOUBLESTRIDE is only ran when using NV12.
This is not correct, as we might first set the bith when using NV12, but
never clear it when using other formats.

Fix it so that when the bit is available (when the HW supports NV12) we
always either set or clear the bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The omap_dss_find_output() function is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Structs omap_overlay and omap_overlay_manager are not used, remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove unused fields in struct omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

get_resolution is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

get_dimensions function pointer is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The RFBI driver has not worked nor compiled for many years. There are
very few boards out there that use RFBI, and no one has stepped up to
fix it.

So let's remove the RFBI code that doesn't even compile.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove DPI's legacy data_lines code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

recommended_bpp hasn't been used for ages, remove the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove extra includes related to non-DT boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Define compat_ioctl in omapdriver_fops to make it possible to use 32bit
apps on 64bit platform.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Fix a few type issues that cause compile warnings on 64 bit ARM
compiler. The change should not affect 32bit platforms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We only use read_irqenable() to flush posted write. Instead of having a
separate function for this, do the flush implicitly in write_irqenable().
Thus we can remove read_irqenable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

At the moment we have ovl_set_channel_out() to configure the output
channel of an overlay. It makes sense to have this configuration as part
of the rest of overlay configuration, and in DSS6+ we need the output
channel when doing the other overlay configuration.

This patch adds a 'channel' parameter to ovl_setup(), so that all
overlay configuration is done via the same function, and removes the
ovl_set_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

ovl_enabled() is not used anywhere, so remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We have been using DRM_MODE_CONNECTOR_Unknown for many of our outputs
because there has not been a proper connector type for them.

We now have connector type for DPI so let's take it into use. At the
same time, add better connector types for the remaining outputs too.

This patch sets the following outputs to use the following connector
types:

DPI -> DPI
DBI -> DPI (MIPI DBI is very similar to DPI at the bus level)
SDI -> LVDS (SDI, TI Flatlink 3G, is a type of LVDS)
VENC -> SVIDEO or Composite
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>