- 25 May, 2021 8 commits
-
-
Peng Li authored
According to the chackpatch.pl, comparison to NULL could be written "!card". Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Peng Li authored
Add space required after that close brace '}'. Add space required before the open parenthesis '(' and '{' Signed-off-by: -
Peng Li authored
Fix the checkpatch error as "foo* bar" and should be "foo *bar". Signed-off-by:
-
Peng Li authored
This patch fixes the checkpatch error about missing a blank line after declarations. Signed-off-by:
-
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
Jiapeng Chong authored
Eliminate the follow smatch warning: drivers/net/hamradio/6pack.c:728 sixpack_ioctl() warn: inconsistent indenting. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
-
Huazhong Tan authored
The Linux kernel has support for a dynamic interrupt moderation algorithm known as "dimlib". Replace the custom driver-specific implementation of dynamic interrupt moderation with the kernel's algorithm. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Nigel Christian authored
The variable br is assigned a value that is not being read after exiting case IFLA_STATS_LINK_XSTATS_SLAVE. The assignment is redundant and can be removed. Addresses-Coverity ("Unused value") Signed-off-by:Nigel Christian <nigel.l.christian@gmail.com> Signed-off-by:
-
- 24 May, 2021 32 commits
-
-
David S. Miller authored
Guangbin Huang says: ==================== net: wan: clean up some code style issues This patchset clean up some code style issues. ==================== Signed-off-by: -
Peng Li authored
Braces {} should be used on all arms of this statement. Signed-off-by: -
Peng Li authored
Block comments use * on subsequent lines. Block comments use a trailing */ on a separate line. Signed-off-by:
-
Peng Li authored
According to the chackpatch.pl, comparison to NULL could be written "!card". Signed-off-by:
-
Peng Li authored
Should not use assignment in if condition. Signed-off-by:
-
Peng Li authored
Add space required after that close brace '}'. Add space required before the open parenthesis '('. Signed-off-by: -
Peng Li authored
Trailing statements should be on next line. Signed-off-by:
-
Peng Li authored
Code indent should use tabs where possible. Signed-off-by:
-
Peng Li authored
This patch fixes the checkpatch error about missing a blank line after declarations. Signed-off-by:
-
Peng Li authored
Fix the checkpatch error as "foo* bar" and should be "foo *bar", and "(foo*)" should be "(foo *)". Signed-off-by:
-
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== SJA1105 DSA driver preparation for new switch introduction (SJA1110) This series contains refactoring patches which are necessary before the support for the new NXP SJA1110 switch can be introduced in this driver. As far as this series is concerned, here is the list of major changes introduced with the SJA1110: - 11 ports vs 5 - port 0 goes to the internal microcontroller, so it is unused as far as DSA is concerned - the Clock Generation Unit does not need any configuration for setting up the PLLs for MII/RMII/RGMII - the L2 Policing Table contains multicast policers too, not just broadcast and per-traffic class. These must be minimally initialized. - more frame buffers ==================== Signed-off-by: -
Vladimir Oltean authored
The shared frame buffer of the SJA1110 is larger than that of SJA1105, which is natural due to the fact that there are more ports. Introduce yet another property in struct sja1105_info which encodes the maximum number of 128 byte blocks that can be used for frame buffers. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
The SJA1110 policer array is similar in layout with SJA1105, except it contains one multicast policer per port at the end. Detect the presence of multicast policers based on the maximum number of supported L2 Policing Table entries, and make those policers have a shared index equal to the port's default policer. Letting the user configure these policers is not supported at the moment. Signed-off-by:
-
Vladimir Oltean authored
Using sja1105_xfer_buf results in a higher overhead and is harder to read. Signed-off-by:
-
Vladimir Oltean authored
Due to the fact that the port count is different, some static config tables have a different number of elements in SJA1105 compared to SJA1110. Such an example is the L2 Policing table, which has 45 entries in SJA1105 (one per port x traffic class, and one broadcast policer per port) and 110 entries in SJA1110 (one per port x traffic class, one broadcast and one multicast policer per port). Similarly, the MAC Configuration Table, the L2 Forwarding table, all have a different number of elements simply because the port count is different, and although this can be accounted for by looking at ds->ports, the policing table can't because of the presence of the extra multicast policers. The common denominator for the static config initializers for these tables is that they must set up all the entries within that table. So the simplest way to account for these differences in a uniform manner is to look at struct sja1105_table_ops::max_entry_count. For the sake of uniformity, this patch makes that change also for tables whose number of elements did not change in SJA1110, like the xMII Mode Parameters, the L2 Lookup Parameters, General Parameters, AVB Parameters (all of these are singleton tables with a single entry). Signed-off-by:
-
Vladimir Oltean authored
There are two distinct code paths which enter sja1105_clocking.c, one through sja1105_clocking_setup() and the other through sja1105_clocking_setup_port(): sja1105_static_config_reload sja1105_setup | | | +------------------+ | | v v sja1105_clocking_setup sja1105_adjust_port_config | | v | sja1105_clocking_setup_port <------------------+ As opposed to SJA1105, the SJA1110 does not need any configuration of the Clock Generation Unit in order for xMII ports to work. Just RGMII internal delays need to be configured, and that is done inside sja1105_clocking_setup_port for the RGMII ports. So this patch introduces the concept of a "reserved address", which the CGU configuration functions from sja1105_clocking.c must check before proceeding to do anything. The SJA1110 will have reserved addresses for the CGU PLLs for MII/RMII/RGMII. Additionally, make sja1105_clocking_setup() a function pointer so it can be overridden by the SJA1110. Even though nothing port-related needs to be done in the CGU, there are some operations such as disabling the watchdog clock which are unique to the SJA1110. Signed-off-by: -
Vladimir Oltean authored
If @port is unused, then dsa_upstream_port(ds, port) returns @port, which means we cannot assume the CPU port can be retrieved this way. The sja1105 switches support a single CPU port, so just iterate over the switch ports and stop at the first CPU port we see. Signed-off-by:
-
Vladimir Oltean authored
Introduce a SJA1105_MAX_NUM_PORTS macro which at the moment is equal to SJA1105_NUM_PORTS (5). With the introduction of SJA1110, these structures will need to hold information for up to 11 ports. Signed-off-by:
-
Vladimir Oltean authored
Do not put unused ports in the forwarding domain, and do not allocate FDB entries for dynamic address learning for them. Signed-off-by:
-
Vladimir Oltean authored
The sja1105 driver will gain support for the next-gen SJA1110 switch, which is very similar except for the fact it has more than 5 ports. So we need to replace the hardcoded SJA1105_NUM_PORTS in this driver with ds->num_ports. This patch is as mechanical as possible (save for the fact that ds->num_ports is not an integer constant expression). Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: add two promisc mode updates This series includes two updates related to promisc mode for the HNS3 ethernet driver. ==================== Signed-off-by: -
Jian Shen authored
Currently, PF is using HCLGE_STATE_PROMISC_CHANGED to indicate need synchronize the promisc mode for itself, and using flag HCLGE_VPORT_STATE_PROMISC_CHANGE for its VF. To keep consistent, remove flag HCLGE_STATE_PROMISC_CHANGED, and use flag HCLGE_VPORT_STATE_PROMISC_CHANGE instead. Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
Currently, when host set VF untrusted, the driver will disable the promisc mode of VF. It may be conflicted when the VF requests the host to set promisc mode. So refactor it by changing promisc mode for VF asynchronously. With this change, the promisc mode of VF can be restored when the VF being trusted again. Signed-off-by:
-
wengjianfeng authored
In function st_nci_hci_network_init, the variable r is assigned then goto exit label, which just return r, so we use return to replace it. and exit label only used once at here, so we remove exit label. Signed-off-by:
wengjianfeng <wengjianfeng@yulong.com> Signed-off-by:
-
YueHaibing authored
Issue identified with Coccinelle. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Florian Fainelli authored
Use phy_ethtool_nway_reset() since the driver makes use of the PHY library. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== net: r6040: Non-functional changes These two patches clean up the r6040 driver a little bit in preparation for adding additional features such as dumping MAC counters and properly dealing with DMA-API mapping. ==================== Signed-off-by: -
Florian Fainelli authored
Instead of the open coded constant 4. Signed-off-by:
-
Florian Fainelli authored
This is not a functional change, but we should be using a logical or to assign the bits we will be writing to the MDIO read and write registers. Signed-off-by:
-
YueHaibing authored
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
-
YueHaibing authored
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
-
