Patch (b6c7a324 "MIPS: Fix get_frame_info() handling of
microMIPS function size.") introduces additional function size
check for microMIPS by only checking insn between ip and ip + func_size.
However, func_size in get_frame_info() is always 0 if KALLSYMS is not
enabled. This causes get_frame_info() to return immediately without
calculating correct frame_size, which in turn causes "Can't analyze
schedule() prologue" warning messages at boot time.

This patch removes func_size check, and let the frame_size check run
up to 128 insns for both MIPS and microMIPS.
Signed-off-by: Jun-Ru Chang <jrjang@realtek.com>
Signed-off-by: Tony Wu <tonywu@realtek.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6c7a324 ("MIPS: Fix get_frame_info() handling of microMIPS function size.")
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <macro@mips.com>
Cc: <yamada.masahiro@socionext.com>
Cc: <peterz@infradead.org>
Cc: <mingo@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>

DTC introduced an i2c_bus_reg check in v1.4.7, used since Linux v4.20,
which complains about upper case addresses used in the unit name.

nexys4ddr.dts names an I2C device node "ad7420@4B", leading to:

  arch/mips/boot/dts/xilfpga/nexys4ddr.dts:109.16-112.8: Warning
    (i2c_bus_reg): /i2c@10A00000/ad7420@4B: I2C bus unit address format
    error, expected "4b"

Fix this by switching to lower case addresses throughout the file, as is
*mostly* the case in the file already & fairly standard throughout the
tree.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: stable@vger.kernel.org # v4.20+
Cc: linux-mips@vger.kernel.org

On the Loongson-2G/2H/3A/3B there is a hardware flaw that ll/sc and
lld/scd is very weak ordering. We should add sync instructions "before
each ll/lld" and "at the branch-target between ll/sc" to workaround.
Otherwise, this flaw will cause deadlock occasionally (e.g. when doing
heavy load test with LTP).

Below is the explaination of CPU designer:

"For Loongson 3 family, when a memory access instruction (load, store,
or prefetch)'s executing occurs between the execution of LL and SC, the
success or failure of SC is not predictable. Although programmer would
not insert memory access instructions between LL and SC, the memory
instructions before LL in program-order, may dynamically executed
between the execution of LL/SC, so a memory fence (SYNC) is needed
before LL/LLD to avoid this situation.

Since Loongson-3A R2 (3A2000), we have improved our hardware design to
handle this case. But we later deduce a rarely circumstance that some
speculatively executed memory instructions due to branch misprediction
between LL/SC still fall into the above case, so a memory fence (SYNC)
at branch-target (if its target is not between LL/SC) is needed for
Loongson 3A1000, 3B1500, 3A2000 and 3A3000.

Our processor is continually evolving and we aim to to remove all these
workaround-SYNCs around LL/SC for new-come processor."

Here is an example:

Both cpu1 and cpu2 simutaneously run atomic_add by 1 on same atomic var,
this bug cause both 'sc' run by two cpus (in atomic_add) succeed at same
time('sc' return 1), and the variable is only *added by 1*, sometimes,
which is wrong and unacceptable(it should be added by 2).

Why disable fix-loongson3-llsc in compiler?
Because compiler fix will cause problems in kernel's __ex_table section.

This patch fix all the cases in kernel, but:

+. the fix at the end of futex_atomic_cmpxchg_inatomic is for branch-target
of 'bne', there other cases which smp_mb__before_llsc() and smp_llsc_mb() fix
the ll and branch-target coincidently such as atomic_sub_if_positive/
cmpxchg/xchg, just like this one.

+. Loongson 3 does support CONFIG_EDAC_ATOMIC_SCRUB, so no need to touch
edac.h

+. local_ops and cmpxchg_local should not be affected by this bug since
only the owner can write.

+. mips_atomic_set for syscall.c is deprecated and rarely used, just let
it go
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huang Pei <huangpei@loongson.cn>
[paul.burton@mips.com:
  - Simplify the addition of -mno-fix-loongson3-llsc to cflags, and add
    a comment describing why it's there.
  - Make loongson_llsc_mb() a no-op when
    CONFIG_CPU_LOONGSON3_WORKAROUNDS=n, rather than a compiler memory
    barrier.
  - Add a comment describing the bug & how loongson_llsc_mb() helps
    in asm/barrier.h.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: ambrosehua@gmail.com
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Li Xuefeng <lixuefeng@loongson.cn>
Cc: Xu Chenghua <xuchenghua@loongson.cn>

When generating vdso-o32.lds & vdso-n32.lds for use with programs
running as compat ABIs under 64b kernels, we previously haven't included
the compiler flags that are supposedly common to all ABIs - ie. those in
the ccflags-vdso variable.

This is problematic in cases where we need to provide the -m%-float flag
in order to ensure that we don't attempt to use a floating point ABI
that's incompatible with the target CPU & ABI. For example a toolchain
using current gcc trunk configured --with-fp-32=xx fails to build a
64r6el_defconfig kernel with the following error:

  cc1: error: '-march=mips1' requires '-mfp32'
  make[2]: *** [arch/mips/vdso/Makefile:135: arch/mips/vdso/vdso-o32.lds] Error 1

Include $(ccflags-vdso) for the compat VDSO .lds builds, just as it is
included for the native VDSO .lds & when compiling objects for the
compat VDSOs. This ensures we consistently provide the -msoft-float flag
amongst others, avoiding the problem by ensuring we're agnostic to the
toolchain defaults.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: ebb5e78c ("MIPS: Initial implementation of a VDSO")
Cc: linux-mips@vger.kernel.org
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Maciej W . Rozycki <macro@linux-mips.org>
Cc: stable@vger.kernel.org # v4.4+

The MIPS VDSO build currently doesn't provide the -msoft-float flag to
the compiler as the kernel proper does. This results in an attempt to
use the compiler's default floating point configuration, which can be
problematic in cases where this is incompatible with the target CPU's
-march= flag. For example decstation_defconfig fails to build using
toolchains in which gcc was configured --with-fp-32=xx with the
following error:

    LDS     arch/mips/vdso/vdso.lds
  cc1: error: '-march=r3000' requires '-mfp32'
  make[2]: *** [scripts/Makefile.build:379: arch/mips/vdso/vdso.lds] Error 1

The kernel proper avoids this error because we build with the
-msoft-float compiler flag, rather than using the compiler's default.
Pass this flag through to the VDSO build so that it too becomes agnostic
to the toolchain's floating point configuration.

Note that this is filtered out from KBUILD_CFLAGS rather than simply
always using -msoft-float such that if we switch the kernel to use
-mno-float in the future the VDSO will automatically inherit the change.

The VDSO doesn't actually include any floating point code, and its
.MIPS.abiflags section is already manually generated to specify that
it's compatible with any floating point ABI. As such this change should
have no effect on the resulting VDSO, apart from fixing the build
failure for affected toolchains.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Kevin Hilman <khilman@baylibre.com>
References: https://lore.kernel.org/linux-mips/1477843551-21813-1-git-send-email-linux@roeck-us.net/
References: https://kernelci.org/build/id/5c4e4ae059b5142a249ad004/logs/
Fixes: ebb5e78c ("MIPS: Initial implementation of a VDSO")
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.4+

Don't set octeon_dma_bar_type if PCI is disabled. This avoids creation
of the MSI irqchip later on, and saves a bit of memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a214720c ("Disable MSI also when pcie-octeon.pcie_disable on")
Cc: stable@vger.kernel.org # v3.3+
Cc: linux-mips@vger.kernel.org

According to the Schematic, the hardware of ci20 leads to uart3,
but not to uart2. Uart2 is miswritten in the original code.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips <linux-mips@vger.kernel.org>
Cc: linux-kernel <linux-kernel@vger.kernel.org>
Cc: devicetree@vger.kernel.org
Cc: robh+dt@kernel.org
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: mark.rutland@arm.com
Cc: malat@debian.org
Cc: ezequiel@collabora.co.uk
Cc: ulf.hansson@linaro.org
Cc: syq <syq@debian.org>
Cc: jiaxun.yang <jiaxun.yang@flygoat.com>

The interrupt number set in the devicetree node of the DMA driver was
wrong.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

Pull pstore fixes from Kees Cook:

 - Fix console ramoops to show the previous boot logs (Sai Prakash
   Ranjan)

 - Avoid allocation and leak of platform data

* tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Avoid allocation and leak of platform data
  pstore/ram: Fix console ramoops to show the previous boot logs

Pull gcc-plugins fixes from Kees Cook:
 "Fix ARM per-task stack protector plugin under GCC 9 (Ard Biesheuvel)"

* tag 'gcc-plugins-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: arm_ssp_per_task_plugin: fix for GCC 9+
  gcc-plugins: arm_ssp_per_task_plugin: sign extend the SP mask

Pull networking fixes from David Miller:

 1) Fix endless loop in nf_tables, from Phil Sutter.

 2) Fix cross namespace ip6_gre tunnel hash list corruption, from
    Olivier Matz.

 3) Don't be too strict in phy_start_aneg() otherwise we might not allow
    restarting auto negotiation. From Heiner Kallweit.

 4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.

 5) Memory leak in act_tunnel_key, from Davide Caratti.

 6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.

 7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.

 8) Missing udplite rehash callbacks, from Alexey Kodanev.

 9) Log dirty pages properly in vhost, from Jason Wang.

10) Use consume_skb() in neigh_probe() as this is a normal free not a
    drop, from Yang Wei. Likewise in macvlan_process_broadcast().

11) Missing device_del() in mdiobus_register() error paths, from Thomas
    Petazzoni.

12) Fix checksum handling of short packets in mlx5, from Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
  bpf: in __bpf_redirect_no_mac pull mac only if present
  virtio_net: bulk free tx skbs
  net: phy: phy driver features are mandatory
  isdn: avm: Fix string plus integer warning from Clang
  net/mlx5e: Fix cb_ident duplicate in indirect block register
  net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
  net/mlx5e: Fix wrong error code return on FEC query failure
  net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
  tools: bpftool: Cleanup license mess
  bpf: fix inner map masking to prevent oob under speculation
  bpf: pull in pkt_sched.h header for tooling to fix bpftool build
  selftests: forwarding: Add a test case for externally learned FDB entries
  selftests: mlxsw: Test FDB offload indication
  mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
  net: bridge: Mark FDB entries that were added by user as such
  mlxsw: spectrum_fid: Update dummy FID index
  mlxsw: pci: Return error on PCI reset timeout
  mlxsw: pci: Increase PCI SW reset timeout
  mlxsw: pci: Ring CQ's doorbell before RDQ's
  MAINTAINERS: update email addresses of liquidio driver maintainers
  ...

Yue Hu noticed that when parsing device tree the allocated platform data
was never freed. Since it's not used beyond the function scope, this
switches to using a stack variable instead.
Reported-by: Yue Hu <huyue2@yulong.com>
Fixes: 35da6094 ("pstore/ram: add Device Tree bindings")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>

GCC 9 reworks the way the references to the stack canary are
emitted, to prevent the value from being spilled to the stack
before the final comparison in the epilogue, defeating the
purpose, given that the spill slot is under control of the
attacker that we are protecting ourselves from.

Since our canary value address is obtained without accessing
memory (as opposed to pre-v7 code that will obtain it from a
literal pool), it is unlikely (although not guaranteed) that
the compiler will spill the canary value in the same way, so
let's just disable this improvement when building with GCC9+.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

The ARM per-task stack protector GCC plugin hits an assert in
the compiler in some case, due to the fact the the SP mask
expression is not sign-extended as it should be. So fix that.
Suggested-by: Kugan Vivekanandarajah <kugan.vivekanandarajah@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
 "Fixes and cleanups all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost/scsi: Use copy_to_iter() to send control queue response
  vhost: return EINVAL if iovecs size does not match the message size
  virtio-balloon: tweak config_changed implementation
  virtio: don't allocate vqs when names[i] = NULL
  virtio_pci: use queue idx instead of array idx to set up the vq
  virtio: document virtio_config_ops restrictions
  virtio: fix virtio_config_ops description

Pull btrfs fixes from David Sterba:
 "A handful of fixes (some of them in testing for a long time):

   - fix some test failures regarding cleanup after transaction abort

   - revert of a patch that could cause a deadlock

   - delayed iput fixes, that can help in ENOSPC situation when there's
     low space and a lot data to write"

* tag 'for-5.0-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: wakeup cleaner thread when adding delayed iput
  btrfs: run delayed iputs before committing
  btrfs: wait on ordered extents on abort cleanup
  btrfs: handle delayed ref head accounting cleanup in abort
  Revert "btrfs: balance dirty metadata pages in btrfs_finish_ordered_io"

Merge tags 'compiler-attributes-for-linus-v5.0-rc3' and 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux

Pull misc clang fixes from Miguel Ojeda:

  - A fix for OPTIMIZER_HIDE_VAR from Michael S Tsirkin

  - Update clang-format with the latest for_each macro list from Jason
    Gunthorpe

* tag 'compiler-attributes-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
  include/linux/compiler*.h: fix OPTIMIZER_HIDE_VAR

* tag 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
  clang-format: Update .clang-format with the latest for_each macro list

If an input number x for int_sqrt64() has the highest bit set, then
fls64(x) is 64.  (1UL << 64) is an overflow and breaks the algorithm.

Subtracting 1 is a better guess for the initial value of m anyway and
that's what also done in int_sqrt() implicitly [*].

[*] Note how int_sqrt() uses __fls() with two underscores, which already
    returns the proper raw bit number.

    In contrast, int_sqrt64() used fls64(), and that returns bit numbers
    illogically starting at 1, because of error handling for the "no
    bits set" case. Will points out that he bug probably is due to a
    copy-and-paste error from the regular int_sqrt() case.
Signed-off-by: Florian La Roche <Florian.LaRoche@googlemail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 594cc251 ("make 'user_access_begin()' do 'access_ok()'")
makes the access_ok() check part of the user_access_begin() preceding a
series of 'unsafe' accesses.  This has the desirable effect of ensuring
that all 'unsafe' accesses have been range-checked, without having to
pick through all of the callsites to verify whether the appropriate
checking has been made.

However, the consolidated range check does not inhibit speculation, so
it is still up to the caller to ensure that they are not susceptible to
any speculative side-channel attacks for user addresses that ultimately
fail the access_ok() check.

This is an oversight, so use __uaccess_begin_nospec() to ensure that
speculation is inhibited until the access_ok() check has passed.
Reported-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arm64 fixes from Will Deacon:
 "Three arm64 fixes for -rc3.

  We've plugged a couple of nasty issues involving KASLR-enabled
  kernels, and removed a redundant #define that was introduced as part
  of the KHWASAN fixes from akpm at -rc2.

   - Fix broken kpti page-table rewrite in bizarre KASLR configuration

   - Fix module loading with KASLR

   - Remove redundant definition of ARCH_SLAB_MINALIGN"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kasan, arm64: remove redundant ARCH_SLAB_MINALIGN define
  arm64: kaslr: ensure randomized quantities are clean to the PoC
  arm64: kpti: Update arm64_kernel_use_ng_mappings() when forced on

Daniel Borkmann says:

====================
pull-request: bpf 2019-01-20

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.

2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.

3) Fix map in map masking to prevent out-of-bounds access under
   speculative execution, from Daniel.

4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
   pacing, from Yuchung.

5) Fix json writer license in bpftool, from Thomas.

6) Fix AF_XDP to check if an actually queue exists during umem
   setup, from Krzysztof.

7) Several fixes to BPF stackmap's build id handling. Another fix
   for bpftool build to account for libbfd variations wrt linking
   requirements, from Stanislav.

8) Fix BPF samples build with clang by working around missing asm
   goto, from Yonghong.

9) Fix libbpf to retry program load on signal interrupt, from Lorenz.

10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:

    BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
    BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942

    kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
    check_memory_region_inline mm/kasan/kasan.c:260 [inline]
    check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
    memcpy+0x23/0x50 mm/kasan/kasan.c:302
    memcpy include/linux/string.h:345 [inline]
    skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    __pskb_copy include/linux/skbuff.h:1053 [inline]
    pskb_copy include/linux/skbuff.h:2904 [inline]
    skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
    ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
    sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
    __netdev_start_xmit include/linux/netdevice.h:4325 [inline]
    netdev_start_xmit include/linux/netdevice.h:4334 [inline]
    xmit_one net/core/dev.c:3219 [inline]
    dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
    __dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
    dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
    __bpf_tx_skb net/core/filter.c:2016 [inline]
    __bpf_redirect_common net/core/filter.c:2054 [inline]
    __bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
    ____bpf_clone_redirect net/core/filter.c:2094 [inline]
    bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
    bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000

The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.

Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.

Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.

The test itself can be run only from commit 1cf1cae9 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.

Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.

Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use napi_consume_skb() to get bulk free.  Note that napi_consume_skb is
safe to call in a non-napi context as long as the napi_budget flag is
correct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS fixes from Paul Burton:

 - Fix IPI handling for Lantiq SoCs, which was broken by changes made
   back in v4.12.

 - Enable OF/DT serial support in ath79_defconfig to give us working
   serial by default.

 - Fix 64b builds for the Jazz platform.

 - Set up a struct device for the BCM47xx SoC to allow BCM47xx drivers
   to perform DMA again following the major DMA mapping changes made in
   v4.19.

 - Disable MSI on Cavium Octeon systems when the pcie_disable command
   line parameter introduced in v3.3 is used, in order to avoid
   inadvetently accessing PCIe controller registers despite the command
   line.

 - Fix a build failure for Cavium Octeon kernels with kexec enabled,
   introduced in v4.20.

 - Fix a regression in the behaviour of semctl/shmctl/msgctl IPC
   syscalls for kernels including n32 support but not o32 support caused
   by some cleanup in v3.19.

* tag 'mips_fixes_5.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: OCTEON: fix kexec support
  mips: fix n32 compat_ipc_parse_version
  Disable MSI also when pcie-octeon.pcie_disable on
  MIPS: BCM47XX: Setup struct device for the SoC
  MIPS: jazz: fix 64bit build
  MIPS: ath79: Enable OF serial ports in the default config
  MIPS: lantiq: Use CP0_LEGACY_COMPARE_IRQ
  MIPS: lantiq: Fix IPI interrupt handling

Pull Devicetree fix from Rob Herring:
 "A single build fix for powerpc due to device_node.type removal"

* tag 'devicetree-fixes-for-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  powerpc: chrp: Use of_node_is_type to access device_type

Pull libnvdimm fixes from Dan Williams:
 "A crash fix, a build warning fix, a miscellaneous small cleanups.

  In case anyone is looking for them, there was a regression caught by
  testing that caused two patches to be dropped from this update.  Those
  patches have been reworked and will soak for another week / re-target
  5.0-rc4.

   - Fix driver initialization crash due to the inability to report an
     'error' state for a DIMM's security capability.

   - Build warning fix for little-endian ARM64 builds

   - Fix a potential race between the EDAC driver's usage of the NFIT
     SMBIOS id for a DIMM and the driver shutdown path.

   - A small collection of one-line benign cleanups for duplicate
     variable assignments, a duplicate header include and a mis-typed
     function argument"

* tag 'libnvdimm-fixes-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm/security: Fix nvdimm_security_state() state request selection
  acpi/nfit: Remove duplicate set nd_set in acpi_nfit_init_interleave_set()
  acpi/nfit: Fix race accessing memdev in nfit_get_smbios_id()
  libnvdimm/dimm: Fix security capability detection for non-Intel NVDIMMs
  nfit: Mark some functions as __maybe_unused
  ACPI/nfit: delete the function to_acpi_nfit_desc
  ACPI/nfit: delete the redundant header file

Pull watchdog fixes from Wim Van Sebroeck:

 - mt7621_wdt/rt2880_wdt: Fix compilation problem

 - tqmx86: Fix a couple IS_ERR() vs NULL bugs

* tag 'linux-watchdog-5.0-rc-fixes' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: tqmx86: Fix a couple IS_ERR() vs NULL bugs
  watchdog: mt7621_wdt/rt2880_wdt: Fix compilation problem

Pull NFS client fixes from Anna Schumaker:
 "These are mostly fixes for SUNRPC bugs, with a single v4.2
  copy_file_range() fix mixed in.

  Stable bugfixes:
   - Fix TCP receive code on archs with flush_dcache_page()

  Other bugfixes:
   - Fix error code in rpcrdma_buffer_create()
   - Fix a double free in rpcrdma_send_ctxs_create()
   - Fix kernel BUG at kernel/cred.c:825
   - Fix unnecessary retry in nfs42_proc_copy_file_range()
   - Ensure rq_bytes_sent is reset before request transmission
   - Ensure we respect the RPCSEC_GSS sequence number limit
   - Address Kerberos performance/behavior regression"

* tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Address Kerberos performance/behavior regression
  SUNRPC: Ensure we respect the RPCSEC_GSS sequence number limit
  SUNRPC: Ensure rq_bytes_sent is reset before request transmission
  NFSv4.2 fix unnecessary retry in nfs4_copy_file_range
  sunrpc: kernel BUG at kernel/cred.c:825!
  SUNRPC: Fix TCP receive code on archs with flush_dcache_page()
  xprtrdma: Double free in rpcrdma_sendctxs_create()
  xprtrdma: Fix error code in rpcrdma_buffer_create()

Pull SCSI fixes from James Bottomley:
 "A set of 17 fixes. Most of these are minor or trivial.

  The one fix that may be serious is the isci one: the bug can cause hba
  parameters to be set from uninitialized memory. I don't think it's
  exploitable, but you never know"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: cxgb4i: add wait_for_completion()
  scsi: qla1280: set 64bit coherent mask
  scsi: ufs: Fix geometry descriptor size
  scsi: megaraid_sas: Retry reads of outbound_intr_status reg
  scsi: qedi: Add ep_state for login completion on un-reachable targets
  scsi: ufs: Fix system suspend status
  scsi: qla2xxx: Use correct number of vectors for online CPUs
  scsi: hisi_sas: Set protection parameters prior to adding SCSI host
  scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
  scsi: isci: initialize shost fully before calling scsi_add_host()
  scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
  scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
  scsi: core: Synchronize request queue PM status only on successful resume
  scsi: pm80xx: reduce indentation
  scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
  scsi: megaraid_sas: correct an info message
  scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
  scsi: sd: Fix cache_type_store()

Pull block fixes from Jens Axboe:

 - block size setting fixes for loop/nbd (Jan Kara)

 - md bio_alloc_mddev() cleanup (Marcos)

 - Ensure we don't lose the REQ_INTEGRITY flag (Ming)

 - Two NVMe fixes by way of Christoph:
    - Fix NVMe IRQ calculation (Ming)
    - Uninitialized variable in nvmet-tcp (Sagi)

 - BFQ comment fix (Paolo)

 - License cleanup for recently added blk-mq-debugfs-zoned (Thomas)

* tag 'for-linus-20190118' of git://git.kernel.dk/linux-block:
  block: Cleanup license notice
  nvme-pci: fix nvme_setup_irqs()
  nvmet-tcp: fix uninitialized variable access
  block: don't lose track of REQ_INTEGRITY flag
  blockdev: Fix livelocks on loop device
  nbd: Use set_blocksize() to set device blocksize
  md: Make bio_alloc_mddev use bio_alloc_bioset
  block, bfq: fix comments on __bfq_deactivate_entity

Re-run the shell fragment that generated the original list. In particular
this adds the missing xarray related functions.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>

Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.

Prevent the phy driver from registering if the features field is missing.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit in Clang expanded the -Wstring-plus-int warning, showing
some odd behavior in this file.

drivers/isdn/hardware/avm/b1.c:426:30: warning: adding 'int' to a string does not append to the string [-Wstring-plus-int]
                cinfo->version[j] = "\0\0" + 1;
                                    ~~~~~~~^~~
drivers/isdn/hardware/avm/b1.c:426:30: note: use array indexing to silence this warning
                cinfo->version[j] = "\0\0" + 1;
                                           ^
                                    &      [  ]
1 warning generated.

This is equivalent to just "\0". Nick pointed out that it is smarter to
use "" instead of "\0" because "" is used elsewhere in the kernel and
can be deduplicated at the linking stage.

Link: https://github.com/ClangBuiltLinux/linux/issues/309Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 8ce5f841 ("of: Remove struct device_node.type pointer")
removed struct device_node.type pointer, but the conversion to use
of_node_is_type() accessor was missed in chrp_init_IRQ().

Fixes: 8ce5f841 ("of: Remove struct device_node.type pointer")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-01-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')

The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.

Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.

Fixes: f5bc2c5d ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Advertised and configured FEC query failure resulted in printing
wrong error code.

Fixes: 6cfa9460 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.

Prior to:
commit '88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.

Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>