During the split to the auto-parser helper functions, the actual call
of init verbs was lost.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43366Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/993162Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

as the start can be called after stop again, we need to reset state
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

during pause the core should maintain the status-quo on the device and pointers
and not wake up. If app needs it should call DROP explcitly.
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The PCI ID entries of Creative SoundCore3D HD-audio controllers should
be before the wildcard for vendor = Creative.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The audio clients have to be disabled before disabling the VGA and
switching.  Similarly, enabling the audio client should be done at
last.  Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Tested-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When VGA_SWITCHEROO support is enabled hda_intel initialises the HDMI
audio device on the current VGA device.  When it's not enabled it only
initialises the HDMI device on the default VGA adaptor, this means
secondary cards get no audio support which is very unhelpful for
multi-seat!

With this patch, when SUPPORT_VGA_SWITCHEROO is disabled hda_intel
initialises all HDMI audio devices, not just the default VGA.

[minor optimizations by tiwai]
Signed-off-by: Steven Newbury <steve@snewbury.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fix a typo that is built only when CONFIG_VGA_SWITCHEROO=n.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When VGA-switcheroo is built in but unused on systems with multiple
graphics cards, the initializations of non-default graphics cards are
skipped and never enabled (because the switcheroo is activated only
when the controller supports).  The current behavior is for avoiding
the system lockup by accessing the disabled GPU, but due to the recent
change in VGA-switcheroo, it determines the state simply by checking
with the default VGA device.  This is the culprit.

Now with the new vga_switcheroo_get_client_state(), we can know the
initial state of the bound GPU, thus can determine the initial audio
client state more correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add vga_switcheroo_get_client_state() to get the current state of the
client.  This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In 3.5 kernel, the endpoint is assigned dynamically for the
substreams, but the PCM assignment still checks the presence of the
endpoint pointer.  This ended up in duplicated PCM substream creations
at probing time, resulting in kernel warnings like:

WARNING: at fs/proc/generic.c:586 proc_register+0x169/0x1a6()
Pid: 1152, comm: modprobe Not tainted 3.5.0-rc1-00110-g71fae7e7 #2
Call Trace:
 [<ffffffff8102a400>] warn_slowpath_common+0x83/0x9c
 [<ffffffff8102a4bc>] warn_slowpath_fmt+0x46/0x48
 [<ffffffff813829ad>] ? add_preempt_count+0x39/0x3b
 [<ffffffff811292f0>] proc_register+0x169/0x1a6
 [<ffffffff8112962e>] create_proc_entry+0x74/0x8c
 [<ffffffffa018eb63>] snd_info_register+0x3e/0xc3 [snd]
 [<ffffffffa01fde2e>] snd_pcm_new_stream+0xb1/0x404 [snd_pcm]
 [<ffffffffa024861f>] snd_usb_add_audio_stream+0xd2/0x230 [snd_usb_audio]
 [<ffffffffa0241d33>] ? snd_usb_parse_audio_format+0x252/0x34f [snd_usb_audio]
 [<ffffffff810d6b17>] ? kmem_cache_alloc_trace+0xab/0xbb
 [<ffffffffa0248c29>] snd_usb_parse_audio_interface+0x4ac/0x567 [snd_usb_audio]
 [<ffffffffa023f0ff>] snd_usb_create_stream+0xe9/0x125 [snd_usb_audio]
 [<ffffffffa023f9b1>] usb_audio_probe+0x62a/0x72c [snd_usb_audio]
 .....

This patch fixes the regression by checking the fixed endpoint number
for each substream instead of the endpoint pointer.
Reported-and-tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This allows the module to automatically load when instantiated from
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rather than having varying timeouts depending on the transition always
use a 4s timeout. This provides better diagnostics for clocking errors
and ensures compatibility with current calibration firmwares.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We should only add source widgets to the input list.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure that the dpcm_get_be() only returns BE DAI links.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.

There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Ensure that all the actions get taken at appropriate times by calling the
_PRE and _POST events for the aifNclk_ev functions explicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we check the correct path for capture.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Pull device-mapper updates from Alasdair G Kergon:
 "Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.

If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes.  Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes).  This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Pull networking updates from David Miller:

 1) Make syn floods consume significantly less resources by

    a) Not pre-COW'ing routing metrics for SYN/ACKs
    b) Mirroring the device queue mapping of the SYN for the SYN/ACK
       reply.

    Both from Eric Dumazet.

 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.

 3) Validate the length requested when building a paged SKB for a
    socket, so we don't overrun the page vector accidently.  From Jason
    Wang.

 4) When netlabel is disabled, we abort all IP option processing when we
    see a CIPSO option.  This isn't the right thing to do, we should
    simply skip over it and continue processing the remaining options
    (if any).  Fix from Paul Moore.

 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
    Apfelbaum.

 6) 8139cp enables the receiver before the ring address is properly
    programmed, which potentially lets the device crap over random
    memory.  Fix from Jason Wang.

 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
    address reference in jumbo RX frame processing from Bruce Allan and
    Sebastian Andrzej Siewior, respectively.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  fec_mpc52xx: fix timestamp filtering
  mcs7830: Implement link state detection
  e1000e: fix Rapid Start Technology support for i217
  e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
  r8169: call netif_napi_del at errpaths and at driver unload
  tcp: reflect SYN queue_mapping into SYNACK packets
  tcp: do not create inetpeer on SYNACK message
  8139cp/8139too: terminate the eeprom access with the right opmode
  8139cp: set ring address before enabling receiver
  cipso: handle CIPSO options correctly when NetLabel is disabled
  net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
  bql: Avoid possible inconsistent calculation.
  bql: Avoid unneeded limit decrement.
  bql: Fix POSDIFF() to integer overflow aware.
  net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
  net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
  net/mlx4_core: Fixes for VF / Guest startup flow
  net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
  net/mlx4_core: Fix number of EQs used in ICM initialisation
  net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int

Pull straggler x86 fixes from Peter Anvin:
 "Three groups of patches:

  - EFI boot stub documentation and the ability to print error messages;
  - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
    should never have been ported, and the port is broken and
    potentially dangerous.)
  - ftrace stack corruption fixes.  I'm not super-happy about the
    technical implementation, but it is probably the least invasive in
    the short term.  In the future I would like a single method for
    nesting the debug stack, however."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
  x86, efi: Add EFI boot stub documentation
  x86, efi; Add EFI boot stub console support
  x86, efi: Only close open files in error path
  ftrace/x86: Do not change stacks in DEBUG when calling lockdep
  x86: Allow nesting of the debug stack IDT setting
  x86: Reset the debug_stack update counter
  ftrace: Use breakpoint method to update ftrace caller
  ftrace: Synchronize variable setting with breakpoints

This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.

The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:

  fde86d31 - tty: add lockdep annotations
  8f6576ad - tty: fix ldisc lock inversion trace
  d3ca8b64 - pty: Fix lock inversion
  b1d679af - tty: drop the pty lock during hangup
  abcefe5f - tty/amiserial: Add missing argument for tty_unlock()
  fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call
  d29f3ef3 - tty_lock: Localise the lock

The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull vfs fix and a fix from the signal changes for frv from Al Viro.

The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short".  Al didn't notice, and
made both of them be the unsigned short.

The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  powerpc: Fix size of st_nlink on 64bit

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
  frv: Remove bogus closing parenthesis

commit e57f93cc (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Introduced by commit 6fd84c08
("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.

Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge fixups for the mac NLS tables from Andrew.

* emailed from Andrew Morton, and one cleanup by me:
  nls: fix (and rename) mac NLS table files and config options
  fs/nls/Makefile: remove bogus CONFIG_ assignments

The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).

And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".

So rename the options to be consistent, and be NLS_MAC_xyzzy.  Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These were debug things which snuck through.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull fbdev updates from Florian Tobias Schandinat:
 - driver for AUO-K1900 and AUO-K1901 epaper controller
 - large updates for OMAP (e.g. decouple HDMI audio and video)
 - some updates for Exynos and SH Mobile
 - various other small fixes and cleanups

* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
  video: bfin_adv7393fb: Fix cleanup code
  video: exynos_dp: reduce delay time when configuring video setting
  video: exynos_dp: move sw reset prioir to enabling sw defined function
  video: exynos_dp: use devm_ functions
  fb: handle NULL pointers in framebuffer release
  OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
  OMAPDSS: Apply VENC timings even if panel is disabled
  OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
  OMAPDSS: DISPC: Support rotation through TILER
  OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
  OMAPFB: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: remove compiler warnings when CONFIG_BUG=n
  OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
  OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
  OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
  OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
  drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
  video: exynos mipi dsi: support reverse panel type
  video: exynos mipi dsi: Properly interpret the interrupt source flags
  video: exynos mipi dsi: Avoid races in probe()
  ...