Change "reg" to "anatop-reg-offset" due to there is a warning of handling no
size field in reg.

This patch also adds the missing device-tree binding documentation.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

DC[2|5]_HIB_MODE is BIT 12 of DCDC[2|5] Control register.
WM8350_DC2_HIB_MODE_ACTIVE/WM8350_DC2_HIB_MODE_DISABLE are defined as 1/0.
Thus we need to left shift WM8350_DC2_HIB_MODE_SHIFT bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

What we want is to restore wm8350->pmic.dcdcx_hib_mode settings to
WM8350_DCDCx_LOW_POWER registers. Current code also clears all other
bits of WM8350_DCDCx_LOW_POWER registers which is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We do not hold a lock while registering regulator, thus should not call unlock
if regulator_register fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

WM831X_DC1_HC_THR_MASK is 0x0070.
We need to do proper shift for setting and getting current limit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet, LDO0 has minimal voltage 1.2V rather than 1.25V.

Table 3-39. VLDO0[2:0] Settings
VLDOx[2:0] VOUT (V) VLDOx[2:0] VOUT (V)
000        1.20     100        2.70
001        1.50     101        2.85
010        1.80     110        3.10
011        2.50     111        3.30
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

TWL specific changes, cross-merged with OMAP due to arch/arm wanting to
use the new ability to override the voltage set and get operations to
support the in-CPU voltage management.  The other changes are minor
fixes, the addition of a few new regulators and device tree support.

Merge remote-tracking branches 'regulator/topic/devm' and 'regulator/topic/stub' into regulator-next

of_parse_phandle() returns NULL either if the property name
itself does not exist or if it (exists and) does not
reference a valid phandle.
Giving out a warn like the one below (that the property references
an invalid phandle) can be confusing when the property itself
does not exist in the node.
Fix it with a more sensible message and make it a dev_dbg instead
of a dev_warn.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

All the callback functions implementation for DCDCx and LDOx are very similar,
I think it is ok to use one tps6507x_pmic_ops for all LDOs and DCDCs.
This refactor removes a couple of duplicated code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Check s5m8767->buck[2|3|4]_gpiodvs status in s5m8767_get_voltage_register
and return correct register accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If we need to ensure only one of the buck[2|3|4]_gpiodvs can be specificed,
check them earlier.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Settling time is require when there is dcdc rail's voltage change.
Returning proper delay time for dcdc voltage change to settle down
the output voltage to new value.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Call tps65912_get_sel_register instead of duplicating the same code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

commit 42b5ef "regulator: tps65912: Use simple equations to get register address"
uses tps65912_get_sel_register to replace tps65912_get_dcdc_sel_register
and tps65912_get_ldo_sel_register.

Now tps65912_set_voltage_dcdc_sel and tps65912_set_voltage_ldo_sel has exactly
the same implementation. Merge them to tps65912_set_voltage_sel function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There is settling time for each rails when it is switched to
ON. Implementing enable time for returning proper settling time
of regulator rails when it is enabled.
Filling the on-time for each rail as per tps65910/tps65911
datasheets.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The address of ctrl and sel registers can be calculated by simple equations.
This patch simplifies the implementation in tps65912_get_ctrl_register and
implements tps65912_get_sel_register to replace tps65912_get_dcdc_sel_register
and tps65912_get_ldo_sel_register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We actually clear LDO_ST_ON_BIT for standby mode in tps65910_set_mode.
Fix the logic in tps65910_get_mode.

Supply state (EEPROM bits):
ST[1:0] = 00 : Off
ST[1:0] = 01 : On high power (ACTIVE)
ST[1:0] = 10 : Off
ST[1:0] = 11 : On low power (SLEEP)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Most callback functions implementation for tps65217_pmic_ldo234_ops and
tps65217_pmic_dcdc_ops are the same except the rid range checking.

This patch uses tps65217_pmic_ops for all DCDCx, LDO2, LDO3, and LDO4.
And rework tps65217_pmic_set_voltage to make it can be called for
DCDCx, LDO2, LDO3, and LDO4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

DIV_ROUND_CLOSEST performs the computation (x + d/2)/d with better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Then we can use the regulator id as array index to access the array.
This change makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This function finds the smallest voltage that falls within the specified range,
and then returns the selector. This rename makes the intention more clear.

Also remove unneeded local variables min_vol and max_vol in s5m8767_set_voltage
and s5m8767_set_voltage_buck.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In the s5m8767_set_voltage_time_sel function, divisor unit is wrong.
ramp_delay is usec unit. So 1000 should be multiplied.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Keep the rails OFF in sleep mode only when the rails are
controlled by external sleep control.
The devices tps65910 and tps65911, both has the sleep input.
The tps65911's sleep input is not same as tps65910's EN3 and hence
taking care of SLEEP input as separate external sleep control input.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Call tps65912_list_voltage_dcdc instead of duplicating the same code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This looks like a mistakenly committed debug logging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>